Direct answer: A 512i to 1024i upgrade replaces Konica KM512i heads with KM1024i heads, which have 1024 nozzles instead of 512 and roughly double the print swath per head. It is not a simple head swap. A typical upgrade needs new KM1024i heads, a 1024i head carriage board, matching adapter or transfer boards and cables, new head mounting plates or brackets, firmware and software that support 1024i, and often a compatible main board, plus checks on the ink supply, power supply and carriage. Done properly, it can raise productivity significantly on a sound machine. On an old or worn machine, the money is often better spent on a newer machine. Always confirm compatibility with your board supplier and calculate payback against your actual order volume before committing.
A 512i to 1024i upgrade can lift output on a sound flex machine, but only if the boards, ink system and demand all support it.

Table of Contents
Many Indian flex units running 8-head Konica 512i machines consider upgrading to 1024i heads to increase speed during peak seasons. This guide explains what changes in a 512i to 1024i upgrade, what the kit includes, indicative costs from public listings, risks and how to decide whether it is worthwhile. For background on the heads themselves, see our comparison of KM512i vs KM1024i printheads.
KM512i vs KM1024i in brief
| Feature | KM512i | KM1024i |
|---|---|---|
| Nozzles per head | 512 (2 rows of 256) | 1024 (4 rows of 256) |
| Native resolution | 360 dpi | 360 dpi |
| Print swath per head | About 36 mm | About 72 mm |
| Typical use in India | Most 10 ft and 16 ft solvent flex machines | Higher-speed solvent and UV machines |
| Board compatibility | 512i boards | 1024i boards |
Because each KM1024i head covers about twice the width of a KM512i head, an 8-head 1024i carriage can print more area per pass than an 8-head 512i carriage, which is where the productivity gain comes from. Actual gains depend on print mode, ink, media, drying and machine mechanics.
What changes in a 512i to 1024i upgrade
1. Printheads
All 512i heads are replaced with 1024i heads of a suitable variant for solvent ink and your drop-size needs. Our KM1024i price guide covers head costs and variants.
2. Head carriage board
512i head boards cannot drive 1024i heads. A 1024i head board with the right head count is required, matching your board system.
3. Adapter / transfer boards and cables
1024i heads use different connectors and cables. New adapter boards and head cables are usually needed.
4. Main board
Some main boards support both 512i and 1024i, depending on brand and version. Many BYHX main board listings describe support for both KM512i and KM1024 heads, but older or other versions may not. If your main board does not support 1024i, it must be replaced too, making this a full kit change.
5. Head mounting plate and brackets
KM1024i heads have different dimensions and mounting from KM512i heads. The head plate or brackets usually need replacing or modification, and alignment must be set precisely.
6. Ink supply system
Larger swath and more nozzles mean higher ink consumption per pass. Sub-tanks, dampers, pumps, filters and tubing must deliver enough ink at stable negative pressure. Weak ink supply causes starvation and dropouts in heavy prints.
7. Power supply
The carriage electronics and heads may draw more power. Confirm that existing supplies are adequate.
8. Firmware and software
Print control software and firmware must support 1024i heads and your configuration. New software versions may be required, along with new head settings, waveforms and calibration.
9. Drying and mechanics
Faster printing puts more ink on the media per minute. Dryers and heaters must keep up. Carriage motors, belts and rails must handle the work reliably. A machine with worn mechanics may not benefit fully.
What a typical upgrade kit includes
| Item | Usually included? | Notes |
|---|---|---|
| 1024i head carriage board | Yes | Matching head count and system |
| Main board | Sometimes | Needed if existing board does not support 1024i |
| Adapter / transfer boards | Usually | Check count and type |
| Head cables and data link | Often | Confirm lengths |
| Software and firmware | Usually | Confirm version and licence |
| Head plate / brackets | Sometimes | May be separate |
| Printheads | Usually separate | Largest cost item |
| Ink system parts | Rarely | Budget separately |
Always ask for a written list of kit contents and confirm what else you need.
Indicative costs from public listings
| Item (late 2026 listings) | Indicative price |
|---|---|
| BYHX KM1024i 8-head head board (Alibaba, Shenzhen supplier) | About $400–$432 |
| BYHX 1024i 8-head printhead board (Econuo) | About $645 |
| BYHX Konica 1024 kit: main board + 8-head board (Alibaba) | About $1,000–$1,100 |
| Konica KM1024i 8-head kit board (Econuo) | About $1,420 |
| BYHX main board for 8× KM512i/KM1024 (Alibaba) | About $478–$820 |
Prices exclude shipping, import duties, GST, heads, installation and calibration. Indian trader prices will differ. Eight new KM1024i heads usually cost much more than the electronics. Check current head prices before planning.
Total upgrade cost: what to include
- Electronics kit (head board, adapters, cables, possibly main board)
- Eight KM1024i heads (or your head count)
- Head plate or brackets
- Ink system upgrades if needed
- Power supply upgrade if needed
- Software licence or update costs
- Technician installation, alignment and calibration
- Downtime during installation and testing
- Ink and media used for testing
- Value recovered by selling old 512i heads and boards, if they are in good condition
Calculating payback
An upgrade pays off only if you can sell the extra output. A simple approach:
- Estimate your current monthly output and how often you turn away or delay jobs.
- Estimate realistic output after upgrade in your common print modes, not the maximum quoted speed.
- Calculate extra monthly profit from additional sellable output.
- Divide total upgrade cost by monthly extra profit to get payback months.
If payback is longer than the expected remaining life of the machine, or if demand is seasonal and uncertain, the upgrade may not make sense. Our guide to estimating 16 ft flex printer production capacity helps with these calculations.
When the upgrade makes sense
- The machine frame, rails, motors and feed system are in good condition
- Demand regularly exceeds current capacity
- The board system supports 1024i with a reasonable kit
- A technician experienced with 1024i installations is available
- Your 512i heads are near the end of life anyway, so new heads are needed regardless
When a new machine may be better
- The machine is old, with worn mechanics or frequent faults
- Drying capacity is limited
- The main board and other electronics are outdated or unsupported
- The cost of upgrade approaches the price difference to a new 1024i machine
- Warranty and support on a new machine are valuable to your business
Indian marketplace listings in late 2026 show Konica 512i flex machines at roughly ₹7.7 lakh to ₹12 lakh. Compare upgrade totals with new 1024i machine quotes from your suppliers before deciding.
Risks and how to manage them
| Risk | Management |
|---|---|
| Incompatible boards or software | Written compatibility confirmation; buy as matched kit |
| Head misalignment | Experienced technician; proper mounting hardware |
| Ink starvation | Check and upgrade ink supply before installation |
| Drying problems at higher speed | Test drying; adjust heaters and dryers |
| Head damage during installation | Test boards and channels before fitting heads; correct voltages |
| Extended downtime | Plan in quiet season; have all parts before starting |
Installation steps in outline
- Confirm kit compatibility and collect all parts before starting.
- Back up existing settings and record machine parameters.
- Remove 512i heads, head board, adapters and cables carefully.
- Install new head plate or brackets.
- Install head board, adapters, cables and, if needed, main board.
- Install and configure software and firmware.
- Test electronics before fitting heads where possible.
- Fit 1024i heads, enter correct voltages and configure waveforms.
- Prime ink, check ink supply and negative pressure.
- Align heads mechanically and run software calibrations.
- Test print in all common modes; adjust drying.
- Monitor closely during the first weeks of production.
What to do with old 512i parts
Working 512i heads and boards have value. They can serve as spares for other 512i machines in your unit or be sold to other units. Test and label them, store heads properly according to supplier guidance, and keep boards in anti-static bags. Be honest about condition when selling.
Example: a sensible upgrade
A flex unit with a well-maintained 16 ft machine was turning away election-season work. Its 512i heads were nearing the end of life, and its BYHX main board version supported 1024i. The unit bought a matched 1024i head board kit, eight new heads and a new head plate, upgraded the ink sub-tanks and scheduled installation in a quiet month. After calibration, output in its common modes rose substantially, and payback came within the next peak season.
Example: an upgrade that should have been a new machine
Another unit attempted an upgrade on an older machine with worn rails and an unsupported main board. The project required a full kit, new heads, ink system changes and repeated mechanical repairs. Total spending approached the cost of a new machine, and reliability remained poor. In hindsight, selling the old machine and buying a new 1024i machine would have been better.
Choosing the right KM1024i variant
KM1024i heads come in variants with different drop sizes, commonly described by names such as SHE, MHE and LHE, with nominal drops around 6, 13 and 42 picolitres. For outdoor flex printing, where speed and coverage matter and viewing distances are long, larger drop variants are often preferred. For closer-viewed work such as indoor displays, smaller drops give finer detail but lower productivity. Discuss your typical jobs with your head and board suppliers before ordering. The board system must support your chosen variant, and waveform files must suit both the variant and your solvent ink.
| Typical job | Drop size consideration |
|---|---|
| Outdoor hoardings, political banners | Larger drops for speed and density |
| Shop boards viewed from a few metres | Medium drops balance speed and detail |
| Indoor displays and close viewing | Smaller drops for finer detail |
Ink compatibility and waveforms
Changing heads is a good moment to review your solvent ink. Some inks are formulated and tested for particular head types. Ask your ink supplier whether your current ink is suitable for KM1024i heads and whether they or your board supplier provide a recommended waveform. Poorly matched ink and waveforms cause unstable jetting, satellites and frequent nozzle loss, which operators may wrongly blame on the new heads. Our guide to solvent ink price and selection in India covers ink choices.
Head alignment and mounting precision
With twice the swath per head, alignment errors become more visible. Heads must be mounted parallel to the carriage travel, at the correct height and with precise spacing between colours and staggered heads. Poor alignment shows as banding, colour misregistration and stitching lines between passes. Quality head plates, proper mounting hardware and patient mechanical alignment before software calibration are essential. Budget technician time for this step; rushing it undermines the whole upgrade.
Training operators for the new configuration
After the upgrade, operators face new print modes, possibly new software, different calibration routines and different cleaning behaviour. Arrange training from the installing technician, write down the new daily procedures and update the head register with the new heads’ serials and voltages. Monitor print quality closely during the first weeks and keep the technician’s contact handy for adjustments. Our guide to head voltage settings explains why voltage discipline matters with any new heads.
Planning the upgrade timeline
- Weeks before: confirm compatibility, order kit, heads and mounting parts, review ink system.
- Days before: verify all parts are received and correct, back up settings, brief customers on downtime.
- Installation days: remove old parts, install electronics and mounting, configure software.
- Calibration days: fit heads, prime, align and calibrate, test print modes.
- First weeks: monitor, fine-tune drying and calibration, train operators.
Avoid starting an upgrade just before peak seasons such as elections or major festivals. If problems arise, you need time to resolve them without losing your most profitable weeks.
Questions to ask before ordering an upgrade kit
- Does my current main board version support KM1024i heads and my head count?
- Which head board, adapter boards and cables are included in the kit?
- Are head plates or brackets included, and do they fit my carriage?
- Which software and firmware versions are supplied, and is a licence needed?
- Which KM1024i variants are supported, and are waveforms provided for my ink?
- Is installation support available, and what warranty applies?
Written answers to these questions help you compare kits fairly and avoid discovering missing parts halfway through installation.
Alternatives to a full upgrade
If the payback is uncertain, consider alternatives: optimising print modes and workflow on your existing machine, replacing worn 512i heads to restore full speed, improving drying so faster modes become usable, or outsourcing peak-season overflow to a partner unit. These options may deliver enough extra capacity at much lower cost and risk.
Further reading: For background on how nozzle count and swath width drive speed, see this overview of inkjet printing.
Key takeaways
- A 512i to 1024i upgrade involves heads, head board, adapters, cables, mounting, software and often the main board.
- KM1024i heads roughly double swath per head, increasing productivity on a sound machine.
- Heads are usually the largest cost; budget for installation, ink system and drying changes too.
- Calculate payback against realistic output and demand.
- On old or worn machines, a new machine may be the better investment.
Considering a 512i to 1024i upgrade? Contact Unified Engineering Dynamics for a compatibility check, kit options and genuine Konica heads.
More in the flex main board series
- Flex Machine Main Board: Functions, Ports and Failure Points
- Flex Main Board Failure Symptoms
- BYHX vs Hoson vs Senyang Main Boards
- Flex Main Board Firmware Update Guide
- USB, Network and Fibre Connection Problems
- Main Board Replacement: Dongle, RIP Licence and Settings
- Surge and Lightning Protection in the Monsoon
- Flex Machine Main Board Price in India
- Used Flex Machine Electronics Check
Related reading on our site: Konica KM512i printhead price and lifespan, KM512i vs KM1024i printheads, flex printer mainboard and head board buyer checks, data and printhead cable handling and the flex printing machine maintenance checklist.
Running an Epson-head eco-solvent machine as well? Our sister series starts with the eco-solvent head carriage board guide and the complete guide to eco-solvent printer electronics.
Frequently Asked Questions
Can I just replace 512i heads with 1024i heads?
No. 1024i heads need a 1024i head board, different adapters and cables, new mounting and software support, and sometimes a new main board.
How much faster is a 1024i machine?
Each KM1024i head covers about twice the swath of a KM512i head, so an 8-head 1024i carriage prints more per pass. Real gains depend on print mode, drying and mechanics.
Do I need a new main board for the upgrade?
It depends on your board system and version. Many BYHX main boards are listed as supporting both 512i and 1024i, but confirm with your supplier.
What is the biggest cost in the upgrade?
Usually the new KM1024i heads. Electronics kits, mounting, ink system changes and installation add to the total.
How much does a 1024i board kit cost?
Late-2026 Chinese listings show BYHX 1024 kits with main board and 8-head board around $1,000–$1,100, and 8-head 1024i head boards around $400–$645, excluding shipping and duties.
Will my ink system cope with 1024i heads?
Not always. Higher ink demand may need larger sub-tanks, better pumps or filters. Check before installation.
Is the upgrade worth it on an old machine?
Often not. Worn mechanics and outdated electronics can make a new machine better value.
How long does the upgrade take?
With all parts ready and an experienced technician, installation and calibration may take a few days. Plan for testing time too.
What happens to my old 512i heads?
Working heads can be kept as spares for other 512i machines or sold. Test, label and store them properly.
Who should install the upgrade?
A technician experienced with 1024i installations on your board system. Poor installation risks head damage and misalignment.
Which KM1024i variant is best for flex printing?
For outdoor flex, larger drop variants are often preferred for speed and density. For close-viewed work, smaller drops give finer detail. Discuss your jobs with your supplier.
Do I need new ink for 1024i heads?
Not always, but confirm with your ink supplier that your ink suits KM1024i heads and ask for a recommended waveform.