Flex Printing

Flex Main Board Firmware Update: When to Update, How to Do It Safely and What Can Go Wrong

Flex Main Board Firmware Update: Safe Step-by-Step Guide

Direct answer: A flex main board firmware update replaces the internal program on the main board (and sometimes the head carriage board) with a newer version from the board system maker. Update only when there is a clear reason: your supplier recommends it to fix a known problem, a replacement board requires matching firmware, or you need a feature such as support for new heads. Before updating, get the exact firmware file for your board model and version from your machine or board supplier, back up all settings, connect the machine and PC to a UPS, and follow the supplier’s procedure without interruption. After updating, re-check head voltages, calibration and settings. An interrupted or mismatched update can leave the board unusable, so if in doubt, have a technician do it.

A flex main board firmware update can fix real problems, but done carelessly it can leave a machine unusable, so preparation matters.

Flex Main Board Firmware Update: Safe Step-by-Step Guide
Flex Main Board Firmware Update: Safe Step-by-Step Guide

Firmware is the hidden layer between your print control software and the hardware. Most flex unit owners never touch it, and that is often wise. But when boards are replaced, software is upgraded or new heads are installed, firmware becomes important. This guide explains what firmware does on a flex machine, when to update and when not to, a safe update procedure and how to recover from problems. It continues our main board series after BYHX vs Hoson vs Senyang main boards.

What firmware does on a flex machine

Firmware is software stored inside the board’s memory. On the main board, it handles tasks such as communicating with the PC, controlling motors, reading sensors, timing print data and managing heaters. On the head carriage board, firmware handles data distribution and head control. The print control software on the PC talks to the firmware using a protocol that both understand.

Board makers release new firmware versions to fix problems, improve performance, add support for new heads or features and keep boards compatible with newer software. Each firmware version is designed for specific board models and versions.

Firmware, software and hardware must match

A flex machine’s electronics work only when three layers match:

LayerExampleWhat happens if mismatched
HardwareMain board and head board models and versionsFirmware may not run or may behave incorrectly
FirmwareProgram on each boardSoftware may not connect; features missing
SoftwarePrint control software on PCErrors, missing options, connection failures

Many “firmware mismatch” or “version error” messages come from one layer being changed without the others. This often happens after a board replacement or software reinstall.

When a firmware update makes sense

  • Supplier-recommended fix: your machine or board supplier identifies a known problem fixed in newer firmware.
  • Replacement board mismatch: a replacement head board or main board needs matching firmware on the other board.
  • Software upgrade: a newer print control software version requires newer firmware.
  • New head support: installing heads or modes that require firmware support.
  • Feature needs: for example, enabling greyscale or improved calibration functions where supported.

When not to update

  • The machine is working well and there is no specific reason
  • You cannot obtain the exact firmware file for your board model and version
  • The power supply at your site is unstable and you have no UPS
  • No backup of settings exists
  • During busy production periods when downtime would be costly
  • Based on advice from an online forum without confirmation from your supplier

“If it isn’t broken, don’t fix it” is a sensible default for firmware on production machines.

Risks of firmware updates

RiskCauseConsequence
Interrupted updatePower cut, cable disconnection, PC crashBoard may not start; may need specialist recovery
Wrong firmware fileFile for different board model or versionBoard may become unusable or behave incorrectly
Mismatched layersUpdating one board but not another or softwareConnection or detection errors
Lost settingsUpdate resets parametersWrong head voltages, calibration lost
Authorisation problemsUpdate affects supplier settingsMachine locked until codes are re-entered

Preparing for a flex main board firmware update

  1. Confirm the reason: write down why the update is needed and who recommended it.
  2. Identify boards exactly: photograph main and head boards and note versions.
  3. Record current firmware and software versions: from the software’s information screens.
  4. Get the correct files from your supplier: firmware and, if needed, matching software.
  5. Back up all settings: export settings files, screenshot head voltages, calibration values and machine parameters.
  6. Record head register: serial numbers and voltages for each head position.
  7. Check authorisation: ask whether codes or supplier settings will need re-entry.
  8. Arrange stable power: connect the PC and, if possible, the machine control circuits to a UPS; avoid times of frequent power cuts.
  9. Use a reliable connection: a short, good-quality cable; disable PC sleep and automatic updates.
  10. Schedule downtime: choose a quiet period and allow time for recalibration.

The update procedure in general terms

Exact steps vary between BYHX, Hoson, Senyang, UMC and other systems, and between versions. Always follow your supplier’s instructions. In general terms, an update involves:

  1. Closing all other programs on the PC.
  2. Opening the firmware update function in the print control software or a separate update tool.
  3. Selecting the correct firmware file for the correct board.
  4. Starting the update and waiting until it completes, without touching the machine, PC or cables.
  5. Restarting the machine and software as instructed.
  6. Confirming the new firmware version in the software’s information screen.

Never switch off the machine or disconnect cables during an update, even if progress seems slow.

After the update: essential checks

  • Confirm the firmware version on each board matches the intended version
  • Check that all heads are detected
  • Verify head voltages against the head register and re-enter if reset
  • Check head temperature settings
  • Re-run calibrations: head alignment, bi-directional, step or feed calibration
  • Check heater and dryer settings
  • Run nozzle checks and test prints
  • Run a production-length job and monitor for errors
  • Export a new settings backup

Our guide to Konica 512i head voltage settings covers voltage verification.

What to do if an update fails

  1. Do not repeatedly power cycle or retry with random files.
  2. Note any error messages and the stage at which the update stopped.
  3. Contact your board or machine supplier with details.
  4. Some systems have recovery modes or procedures; use them only with supplier guidance.
  5. If recovery is not possible on site, the board may need to be reprogrammed by the supplier or a specialist.

This is why having a tested spare board, or at least a supplier who can respond quickly, is valuable before attempting updates.

Firmware and board replacement

Firmware issues are common after replacing a main board or head board. The replacement may have older or newer firmware than the board it works with. Ask the supplier before shipping to load firmware that matches your existing system, or to provide instructions for updating. Our carriage board replacement checklist and main board replacement checklist include firmware steps.

Firmware and software upgrades

Sometimes owners want newer print control software for its features. Newer software may require newer firmware, and newer firmware may require newer hardware versions. Before upgrading software, ask your supplier whether your boards and firmware support it. Keep the installer for your current, working software version so you can return to it if needed.

Keeping firmware records

RecordExample
Main board model and versionFrom board label
Main board firmware versionFrom software info screen
Head board model, version and firmwareFrom label and software
Software name and versionFrom About screen
Date of last update and reasonSupplier-recommended fix for feed error
Who performed the updateTechnician name
Settings backup locationUSB drive and cloud folder

Firmware files: where to get them

Obtain firmware only from your machine supplier, the board maker’s authorised channels or a trusted technician who can confirm the file matches your hardware. Files shared on social media or forums may be for different versions, modified or corrupted. Installing them risks damaging the board and voiding support. Keep a copy of the firmware and software files that work with your machine in a safe place.

Example: an update that fixed a real problem

A flex unit experienced occasional feed errors that a supplier traced to a known firmware issue on its board version. The supplier provided the correct firmware file and instructions. The owner backed up settings, connected the PC to a UPS and scheduled the update for a Sunday. After the update, head voltages were checked and calibrations repeated. The feed errors stopped.

Example: an update that went wrong

Another unit’s operator downloaded a firmware file from an online group, hoping to fix a minor issue. The file was for a different board version. The update failed partway through, and the machine no longer started. The board had to be sent to a specialist for reprogramming, and the machine was down for over a week. The original issue turned out to be a dirty encoder strip.

Firmware on the head carriage board

Firmware is not only on the main board. Head carriage boards and sometimes transfer boards also carry firmware. In many systems, the main board and head board firmware must be compatible, and some update tools update both together while others treat them separately. When a head board is replaced, its firmware may differ from what the main board expects, producing head detection or version errors. Ask your supplier whether your system updates both boards from the main board, requires separate updates, or needs matched firmware loaded before shipping. Our article on carriage board systems and versions covers head board matching.

Understanding version numbers

Firmware and board versions are usually shown as numbers or codes, for example a major version followed by minor revisions. In general, a change in the major number may indicate significant changes in protocol or hardware support, while minor changes often fix problems or adjust features. However, numbering schemes differ between makers, so never assume compatibility from the numbers alone. Always ask the supplier which firmware versions match your exact board versions and software.

ItemWhere to find it
Board hardware versionPrinted label or silkscreen on the board
Firmware versionPrint control software information or diagnostics screen
Software versionSoftware About screen or installer name
Head board firmwareSoftware diagnostics or supplier tool

Firmware and head configuration changes

Changing head type, head count or print modes can require firmware support. For example, enabling greyscale printing, adding heads or switching to 1024i heads may need specific firmware on main and head boards, along with new waveform files and software settings. Plan these changes with your supplier as a package rather than changing parts one at a time. Our guide to the 512i to 1024i upgrade kit explains how firmware fits into upgrades.

A sensible firmware policy for flex units

  • Keep firmware unchanged on stable production machines unless there is a clear reason
  • Record versions for every board and keep copies of working firmware and software
  • Allow only trained staff to perform updates
  • Require supplier confirmation and a backup before any update
  • Schedule updates in quiet periods with a UPS in place
  • Log every update with date, reason, versions and results

A written policy prevents well-meaning operators from experimenting with production machines and gives technicians clear records when problems occur.

Firmware questions to ask your supplier

  1. Which firmware version do you recommend for my board versions and software?
  2. What problem does the new version fix, and is my machine affected?
  3. Does the update affect the head board too?
  4. Will settings or calibration be reset?
  5. Will authorisation codes need re-entry?
  6. Is there a recovery procedure if the update fails?
  7. Can you support the update remotely or on site?

Firmware and calibration data

Calibration values such as head alignment offsets, bi-directional corrections and feed compensation may be stored on the main board, the head board, the PC or a combination, depending on the system. A firmware update can reset values stored on the board while leaving PC-stored values intact, or the reverse. This is why technicians record calibration values before updates and verify them afterwards. If print quality changes after an update, such as new banding or misregistration, re-run calibrations before suspecting hardware. Keeping printed calibration test results from before the update provides a useful comparison.

Signs that firmware may be the problem

Firmware issues are less common than hardware or setup problems, but certain patterns suggest them: errors that started immediately after a board replacement or software change, version mismatch messages, a feature missing that should be available, or a known fault that your supplier confirms is linked to a particular version. In contrast, faults that appear after storms, with heat or with cable movement usually point to hardware, power or connections. Before considering an update, rule out these more common causes, and ask your supplier whether the symptom matches any known firmware issue for your versions.

Further reading: For general background, this overview explains what firmware is and how it differs from ordinary PC software.

Key takeaways

  • A flex main board firmware update changes the board’s internal program and must match hardware and software.
  • Update only for a clear reason, such as a supplier-recommended fix, board replacement or new feature need.
  • Get exact firmware files from trusted sources, back up settings and use stable power.
  • Never interrupt an update; follow supplier procedures exactly.
  • Re-check head voltages, calibration and settings after every update.

Planning a firmware update or facing version errors after a board change? Contact Unified Engineering Dynamics for guidance on matching firmware, boards and software.

More in the flex main board series

Related reading on our site: Konica KM512i printhead price and lifespan, KM512i vs KM1024i printheads, flex printer mainboard and head board buyer checks, data and printhead cable handling and the flex printing machine maintenance checklist.

Running an Epson-head eco-solvent machine as well? Our sister series starts with the eco-solvent head carriage board guide and the complete guide to eco-solvent printer electronics.

Frequently Asked Questions

What is main board firmware on a flex machine?

It is the internal program stored on the main board that handles communication, motion, sensors, heaters and print timing.

Should I update firmware regularly?

Not by default. Update only when your supplier recommends it for a specific fix, when a board replacement requires it, or when you need a supported new feature.

Can a firmware update damage my board?

An interrupted update or wrong file can leave the board unusable, needing specialist recovery. Following correct procedures minimises the risk.

Where should I get firmware files?

From your machine supplier, the board maker’s authorised channels or a trusted technician who confirms compatibility. Avoid files from unverified online sources.

Will a firmware update reset my settings?

It may. Always back up settings, head voltages and calibration values before updating, and verify them afterwards.

Why do I get version errors after replacing a board?

The replacement board may have different firmware from your other board or software. Ask your supplier to match firmware or provide update instructions.

Do I need a UPS for firmware updates?

It is strongly recommended. A power cut during an update is one of the main causes of failed updates.

Can I update the software without updating firmware?

Sometimes, but newer software may require newer firmware. Check with your supplier before upgrading.

What should I do if an update fails?

Stop, note the error, and contact your supplier. Do not repeatedly retry or use random files.

Who should perform firmware updates?

A trained technician or a senior operator following supplier instructions exactly. Inexperienced updates carry higher risk.

Does the head carriage board also have firmware?

Yes. Head boards carry firmware that must be compatible with the main board. Some systems update both together; others need separate updates.

Can I tell compatibility from firmware version numbers?

Not reliably. Numbering schemes differ between makers. Always confirm matching versions with your supplier.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *