Flex Printing

Flex Main Board Replacement Checklist: Dongle, RIP Licence, Authorisation and Settings

Flex Main Board Replacement: Dongle & RIP Licence Checklist

Direct answer: A safe flex main board replacement follows six stages: confirm the old board is really faulty and the cause has been fixed; order an exact match by brand, model, version and head support; check authorisation, supplier codes and software licence requirements before the board arrives; back up every setting and record head voltages and calibration values; install with power off, correct cable connections and anti-static care; then verify firmware, re-enter settings, recalibrate and test thoroughly. Remember that the RIP software licence (often a USB dongle on the PC) is usually separate from the main board and is not affected by a board change, but the print control software may need reconfiguration or supplier authorisation to work with the new board.

A smooth flex main board replacement depends as much on licences, authorisation and settings backups as on the board itself.

Flex Main Board Replacement: Dongle & RIP Licence Checklist
Flex Main Board Replacement: Dongle & RIP Licence Checklist

Replacing a main board is one of the larger electronics jobs on a flex machine. Done carelessly, it can leave the machine locked, mis-calibrated or still faulty. This checklist helps owners and technicians in India plan and complete the job smoothly. It complements our carriage board replacement checklist and our guide to main board failure symptoms.

Stage 1: Confirm the diagnosis and root cause

Before ordering a board, make sure it is really needed:

  • Power supplies tested and delivering correct voltages
  • PC, cables, drivers and settings ruled out for communication faults
  • Motor drivers, motors, sensors and wiring checked for motion faults
  • Heater relays and wiring checked for heater faults
  • Data link and head carriage board checked for all-heads-missing faults
  • Board inspected for visible damage

Equally important is the root cause. If a surge, heater short, failing power supply or poor earthing damaged the old board, the new board will suffer the same fate unless the cause is fixed first.

Stage 2: Order the right board

Collect and send this information to your supplier:

ItemWhy
Photos of old board front and back, showing markingsIdentifies brand, model, version
Board version and serial numberVersion matching
Head carriage board model and versionMain and head boards must match
Firmware and software versionsAvoid mismatch errors
Head type, variant and countBoard must support configuration
Machine brand, model and yearSupporting information
Connection type to PC (USB, network, fibre)Board must match link

Ask for written confirmation of compatibility and clear warranty and return terms. Our comparison of BYHX, Hoson and Senyang main boards explains why brands are not interchangeable.

Stage 3: Authorisation, dongles and licences

This is the stage most often overlooked. Three different things are involved, and owners frequently confuse them:

RIP software licence

RIP software such as PhotoPrint, Maintop or similar is usually licensed separately, often with a USB dongle or software key tied to the PC. It converts artwork into print data. A main board replacement normally does not affect the RIP licence, but keep the dongle safe, as losing or damaging it can stop production. If you also change the PC during repairs, check how your RIP licence transfers.

Print control software

The board system’s print control software communicates with the main board. It may need reinstallation, a newer version or configuration to recognise the new board. Keep installers for your working version.

Board authorisation and supplier settings

Some board systems let machine manufacturers or dealers set board IDs, authorisation passwords or time-limited codes. A replacement board from a third-party seller may need these configured before it works with your machine. Before buying, ask:

  • Does this board need authorisation codes to work with my software?
  • Who can provide the codes: the seller, my machine supplier or the board maker?
  • Will my existing settings or licences transfer?
  • Is there any cost for authorisation?

Resolving this before installation avoids a machine sitting idle while you search for codes.

Stage 4: Back up everything

Before removing the old board, if the machine still communicates even partially, export or record:

  • Print control software settings files
  • Head voltages and serial numbers for each position
  • Head temperature settings
  • Calibration values: head alignment, bi-directional, feed or step calibration
  • Heater and dryer settings
  • Machine parameters such as print width, origin offsets and speeds
  • Network settings if applicable
  • Screenshots of every settings page

If the machine cannot communicate, use your most recent backup and head register. This is why regular backups matter. Our guide to Konica 512i head voltage settings explains the head register.

Stage 5: Pre-installation checks on the new board

  • Compare the new board with photos of the old one: markings, connectors, layout
  • Check for shipping damage, bent pins or loose components
  • Confirm the version matches what was ordered
  • Keep it in its anti-static bag until installation
  • Have the supplier’s installation notes ready

Stage 6: Safe removal and installation

  1. Switch off and isolate the machine at the main supply; wait for capacitors to discharge as advised.
  2. Wear an anti-static wrist strap connected to the machine frame.
  3. Photograph all cable connections before disconnecting.
  4. Label each cable with masking tape and a marker.
  5. Disconnect cables gently, holding connectors, not wires.
  6. Remove mounting screws and the old board.
  7. Inspect the cabinet for damage, dust, moisture or pests; clean if needed.
  8. Mount the new board securely with all screws and spacers.
  9. Reconnect cables exactly as photographed, checking orientation.
  10. Double-check every connection before applying power.

Stage 7: First power-up and firmware

  1. Restore power and observe the board for status LEDs, smell or heat.
  2. Start the print control software and check connection.
  3. Check firmware versions of main and head boards.
  4. Update or match firmware only if required and as instructed by your supplier.
  5. Enter authorisation codes if needed.

Our guide to flex main board firmware updates covers safe update procedures.

Stage 8: Restore settings and calibrate

  • Import settings files or re-enter settings manually
  • Verify head voltages against the head register for every position
  • Check head temperature settings
  • Check heater and dryer settings and confirm heaters respond correctly
  • Run head alignment, bi-directional and feed calibrations
  • Check origin and sensor functions

Stage 9: Testing

  • Nozzle checks for all heads
  • Test prints in common modes
  • Production-length job to check stability
  • Monitor communication stability across the shift
  • Check heater temperatures and ink supply operation

Stage 10: Monitoring and documentation

Monitor the machine closely for the first week. Record the replacement in your machine logbook: date, board details, supplier, firmware and software versions, settings changes and the root cause of the original failure. Export a fresh settings backup once everything is confirmed.

Printable flex main board replacement checklist

StepDone
Diagnosis confirmed; root cause fixed☐
Board details sent; compatibility confirmed in writing☐
Authorisation and licence questions answered☐
Settings, head register and calibration backed up☐
New board inspected☐
Cables photographed and labelled☐
Board installed with ESD precautions☐
Firmware and authorisation completed☐
Settings restored; voltages verified☐
Calibration and testing completed☐
Logbook updated; new backup exported☐

Common mistakes

  • Replacing the board without fixing the power or wiring fault that killed the old one
  • Ordering by machine name without checking version
  • Discovering authorisation requirements only after installation
  • Mixing up cable connections because they were not photographed
  • Assuming head voltages and calibration survived
  • Losing the RIP dongle during PC or workshop rearrangement
  • Skipping the production-length test

Cost and downtime planning

Public IndiaMART listings in late 2026 show a BYHX 512i motherboard at ₹45,000 and UMC main boards for Konica 512i machines at ₹38,000 to ₹40,000, excluding GST. Add technician time, any authorisation charges and downtime. With a board in stock and authorisation resolved, replacement and calibration can often be done within a day. Delays usually come from incorrect orders, missing codes or unresolved root causes. See our main board price guide for more.

Example: a smooth replacement

A flex unit’s main board failed after a monsoon surge. The technician confirmed the diagnosis, the unit installed surge protection, and the owner sent board photos and versions to a supplier, who confirmed compatibility and arranged authorisation in advance. Settings had been backed up the previous month. Installation, firmware matching, settings restoration and calibration were completed in one day, and the machine was printing the next morning.

Example: a replacement held up by authorisation

Another unit bought a low-cost main board online. After installation, the software refused to work with it because of supplier authorisation settings. The machine supplier initially could not be reached, and the unit lost several days of production. Asking about authorisation before purchase would have avoided the delay.

Cable identification on the main board

A main board may have a dozen or more connectors, some of which look similar. Swapping two connectors can damage the board, motors or sensors, or simply produce confusing errors. Before removing any cable:

  • Take a wide photograph of the whole board with all cables connected
  • Take close-up photographs of each connector, showing orientation
  • Label each cable with a number or function, such as “X motor”, “encoder” or “heater 1”
  • Note any connectors that are unused
  • Check for cables secured with ties that will need replacing

When reconnecting, work methodically from one side of the board to the other, matching labels and photos. Have a second person double-check before power-up.

Checking the cabinet while the board is out

The main board replacement is a good opportunity to inspect and clean the cabinet. With power isolated:

ItemCheck
Power suppliesBulging capacitors, burn marks, fan condition
Terminal blocksTightness, discoloration, corrosion
Relays and solid-state relaysBurn marks, signs of overheating
Cabinet fans and filtersClean and working
Cable entriesSealed against dust, pests and moisture
Earth connectionsTight and corrosion-free

Finding and fixing a weak power supply or loose earth during this inspection can prevent the new board from suffering the same fate as the old one.

What to do with the old main board

Do not discard the old board. Depending on the fault, it may be repairable and useful as a spare. Label it with the date, fault symptoms and suspected cause, and store it in an anti-static bag. Ask a specialist repair technician to assess it. A repaired, tested old board becomes an emergency spare that can save days of downtime in future. If the board is under warranty, the supplier may require it to be returned for assessment.

Roles and responsibilities during replacement

PersonResponsibility
OwnerApproves purchase, ensures root cause is fixed, keeps records
TechnicianDiagnosis, installation, firmware, calibration, testing
SupplierCorrect board, compatibility confirmation, authorisation support
ElectricianEarthing, surge protection and power fixes if needed
Senior operatorSettings backup, head register, test prints, monitoring

Agreeing roles in advance prevents steps from being skipped because each person assumed someone else would handle them.

Planning downtime and customer commitments

A main board failure often happens at an inconvenient time. To limit the impact:

  • Inform customers promptly about delays and expected restart dates
  • Consider outsourcing urgent jobs to a trusted partner unit during downtime
  • Schedule the replacement for the earliest time all parts and the technician are available
  • Plan calibration and test prints immediately after installation
  • Prioritise urgent jobs once the machine is back in production

Good communication with customers protects relationships even when the machine is down.

Preventing the next main board failure

After replacement, review what caused the failure and what can prevent another. Common improvements include adding surge protection devices, improving earthing, moving the PC onto the same earthed supply, replacing worn heater wiring, improving cabinet cooling and sealing the cabinet against pests and moisture. Our guide on surge protection in the monsoon covers the most common cause in India.

Test print sequence after replacement

  1. Nozzle check for all heads at operating temperature.
  2. Head alignment and bi-directional calibration prints.
  3. Feed calibration across a long length of media.
  4. Colour bars and density test across the full width.
  5. A typical customer job at production speed.
  6. A long job of at least thirty minutes to check stability.

Compare results with prints from before the failure if you kept them. Any difference in density, alignment or banding suggests settings that were not restored correctly, and should be fixed before returning to full production.

Using a tested spare board as a diagnostic tool

For units with several machines of the same type, a tested spare main board is valuable not only as a replacement but as a diagnostic tool. Swapping in a known good board quickly confirms whether a fault lies in the main board or elsewhere. If the fault disappears, the old board is faulty; if it remains, the problem is in power, wiring, sensors, the PC or the carriage. Use spare boards carefully: install them only after checking that power supplies and wiring are healthy, so the spare is not damaged by the same fault that affected the original. Return the spare to safe storage, labelled and tested, once diagnosis is complete or a permanent replacement arrives.

Further reading: RIP software is covered by a software licence that is usually tied to a dongle or PC, not to the machine main board.

Key takeaways

  • A flex main board replacement starts with a confirmed diagnosis and a fixed root cause.
  • Order an exact match by brand, model, version and head support, with written confirmation.
  • The RIP licence is usually separate from the board, but print control software and authorisation may need attention.
  • Back up settings, photograph connections and verify voltages and calibration after installation.
  • Test thoroughly and document the replacement.

Planning a main board replacement? Contact Unified Engineering Dynamics with your board details for compatibility checks, authorisation guidance and replacement boards.

More in the flex main board series

Related reading on our site: Konica KM512i printhead price and lifespan, KM512i vs KM1024i printheads, flex printer mainboard and head board buyer checks, data and printhead cable handling and the flex printing machine maintenance checklist.

Running an Epson-head eco-solvent machine as well? Our sister series starts with the eco-solvent head carriage board guide and the complete guide to eco-solvent printer electronics.

Frequently Asked Questions

Will replacing the main board affect my RIP licence?

Usually not. RIP licences are commonly tied to a USB dongle or the PC, not the main board. Keep the dongle safe.

Does a new main board need authorisation codes?

Some board systems allow suppliers to set authorisation codes or IDs. Ask the seller and your machine supplier before buying.

What information should I give the board supplier?

Photos of the old board, its version and serial, head board details, firmware and software versions, head type and count, and the PC connection type.

Will my settings transfer to the new board?

Not always. Back up settings beforehand and verify head voltages, calibration and machine parameters after installation.

How long does a main board replacement take?

With the right board, authorisation resolved and settings backed up, often within a day including calibration.

Why did my new main board fail quickly?

Often because the root cause, such as a surge, heater short or failing power supply, was not fixed before installation.

Do I need to update firmware after replacement?

Only if versions do not match or your supplier advises it. Follow supplier instructions carefully.

Can I install a used main board?

Yes, if it is tested, compatible, authorised for your system and comes with a warranty. Ask why it was removed from its original machine.

Should I photograph cables before removing the board?

Yes. Photographs and labels prevent wrong connections, which can damage the new board.

What should I record after replacement?

Date, board details, supplier, firmware and software versions, settings changes, root cause and a fresh settings backup.

Should I keep the old main board after replacement?

Yes. Label and store it; it may be repairable as a spare or needed for a warranty claim.

What should I inspect in the cabinet during replacement?

Power supplies, terminal blocks, relays, fans, filters, cable entries and earth connections, fixing any problems before installing the new board.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *