Direct answer: A solvent flex machine’s electronics form a chain. The PC and RIP prepare the image. The mainboard in the electrical cabinet receives the job, controls motors, heaters and sensors, and sends print data to the carriage. The head board (head carriage board) on the moving carriage splits that data for each head and coordinates timing. The head driver board, or driver section, supplies and switches the drive voltage that makes each head fire. Power supplies feed every link. When a fault appears, the position in this chain decides the symptom: mainboard faults usually stop the whole machine, head board faults affect heads’ data and detection, and driver faults affect firing strength and head safety.
Understanding the head driver board vs head board vs mainboard question turns guesswork into a clear, step-by-step diagnosis of flex machine faults.

Table of Contents
Understanding this chain is the fastest way to stop guessing and start diagnosing. This guide walks through each link on a typical 10 ft or 16 ft Konica flex machine, explains what each board does, compares their failure symptoms and shows how technicians use the chain to locate faults. For background, see what the head driver board does and the head carriage board explained.
The full electronics chain at a glance
| Link | Location | Main job |
|---|---|---|
| PC and RIP software | Operator desk | Prepare image, colour management, send job |
| Print control software | Same PC | Head settings, calibration, job control, communication with mainboard |
| Communication link | PC to machine | USB, network or fibre connection |
| Mainboard | Electrical cabinet | Job buffering, motion control, heaters, sensors, data to carriage |
| Main data link | Cable chain | High-speed data from mainboard to carriage |
| Head carriage board | Carriage | Splits data per head, timing, head detection and status |
| Head driver board / section | Carriage | Regulated drive voltage and firing energy |
| Transfer / adapter boards | Above heads | Connect head cables; may hold driver or protection parts |
| Printheads | Head plate | Fire ink droplets |
| Power supplies | Cabinet and carriage | Feed every board with correct DC voltages |
Link 1: PC, RIP and print control software
The chain starts at the computer. The RIP, such as PhotoPrint, Maintop, Onyx or Ultraprint, converts artwork into printable data with the right colour profiles and resolution. The print control software, supplied with the board system, sends that data to the machine and stores head settings, voltages, temperatures and calibration. Problems at this stage include wrong print modes, corrupted files, driver conflicts on the PC, and incorrect head settings. They can look like hardware faults: banding, wrong colours or failure to start printing.
Link 2: The communication link
The PC connects to the mainboard through USB, Ethernet or, on some systems, fibre. Loose connectors, poor-quality cables, Windows power-saving settings that turn off USB ports and network conflicts can interrupt jobs. Symptoms include “printer not connected”, jobs stopping mid-way or the software losing contact with the machine.
Link 3: The mainboard
The mainboard is the machine’s central controller. It receives and buffers print jobs, controls the carriage motor and media feed motors, manages heaters and dryers, reads sensors such as origin, limit, media and encoder, and sends print data to the carriage at the right time. On many systems it also manages safety functions such as the crash sensor.
Typical mainboard fault symptoms
- Machine does not initialise or carriage does not move
- PC cannot connect to the machine
- Motor, heater or sensor errors
- No heads detected even though carriage electronics are powered
- Errors immediately at power-on
Mainboard faults usually affect the whole machine, not just some heads.
Link 4: The main data link
A high-speed cable or fibre runs through the cable chain to carry data from the mainboard to the carriage. Because it moves with the carriage, it is exposed to repeated bending. Faults typically affect all heads together and may depend on carriage position. Our article on head data cable vs carriage board faults explains how to test it.
Link 5: The head carriage board
On the carriage, the head board decodes incoming data, separates it into streams for each head, synchronises firing with carriage position and reports head status. It also often reads head temperature and controls heaters.
Typical head board fault symptoms
- One or more heads not detected
- Colour missing, with heads apparently powered
- Random firing from data corruption
- Head temperature errors
- Faults on a group of heads served by one section of the board
Link 6: The head driver board or section
The driver section supplies the drive voltage set for each head and delivers the energy for firing. It must remain stable during heavy printing and protect heads from abnormal voltage.
Typical driver fault symptoms
- Weak or faded printing with correct settings
- Nozzle dropout increasing in solid areas
- Heads running hot
- New heads failing soon after installation
- Burnt smell, discoloured components or blown fuses on the carriage
Link 7: Transfer boards and head cables
Small transfer or adapter boards above each head connect head cables to the main carriage electronics. Some carry driver or protection components. Faults here usually affect one head or a pair of heads. Head cables are flat flexible cables that are sensitive to crooked insertion, creasing and ink contamination. Our guide to carriage board connectors explains safe handling.
Link 8: The printheads
Konica KM512i or KM1024i heads are the end of the chain. A head can fail from wear, blockage, drying, crashes or internal electrical damage. An internally shorted head can damage the driver section, which can then damage the next head fitted. This makes the head both a victim and a possible cause in the chain.
Link 9: Power supplies
Every board depends on DC power supplies, typically in the electrical cabinet and sometimes on the carriage. A failing supply can cause symptoms anywhere in the chain: random resets, heads dropping out, weak firing or motor errors. Power supply output should be checked by a technician whenever symptoms are unclear. See our guide on flex printer power supplies.
Head driver board vs head board vs mainboard: which is at fault?
| Symptom | Mainboard | Head board | Driver section | Head / cable |
|---|---|---|---|---|
| Machine won’t initialise | Likely | Unlikely | Unlikely | Unlikely |
| PC cannot connect | Likely (or comms link) | Unlikely | Unlikely | Unlikely |
| All heads not detected | Possible | Likely (or data link) | Possible | Unlikely |
| One head not detected | Unlikely | Possible | Possible | Likely |
| Weak printing, group of heads | Unlikely | Possible | Likely | Possible |
| Random firing | Possible | Possible | Possible | Possible (plus earthing) |
| New head fails quickly | Unlikely | Possible | Likely | Possible (cable) |
| Motor or heater errors | Likely | Unlikely | Unlikely | Unlikely |
“Likely” means the first place to look, not a guaranteed cause. Always confirm by testing.
How technicians use the chain to diagnose
Experienced technicians work along the chain systematically:
- Start with the symptom scope: whole machine, all heads, a group or one head.
- Check upstream first for whole-machine faults: PC, communication, mainboard, power.
- Check the data link for all-head faults: especially if position-dependent.
- Use swap tests for single-head faults: cable, transfer board, head position.
- Measure drive voltage for weak-firing faults: compare with settings under load.
- Test heads before fitting them to suspect channels: to avoid chain damage.
This approach avoids replacing expensive boards on guesswork.
Why one failure can spread along the chain
Electronic faults often travel. A surge entering through the power supply can damage the mainboard and the carriage electronics at once. A shorted head can burn the driver section, which then destroys the next head. A damaged cable can carry a fault from one board to another. This is why technicians insist on finding the root cause before replacing parts. Our article on why a bad head driver board can kill a new Konica head explains this risk in detail.
Cost perspective across the chain
| Part | Relative cost | Notes |
|---|---|---|
| Head cable | Low | Keep spares |
| Transfer / adapter board | Low to medium | Keep spares if separate |
| Main data link | Low to medium | Consider spare for busy units |
| Power supply | Medium | Check before replacing boards |
| Head carriage board | High | Indian listings around ₹60,000 for 512i |
| Mainboard | High | Indian listings around ₹45,000 for BYHX 512i |
| Konica printhead | Very high | Roughly ₹57,000–₹86,000 each in Indian listings |
Prices are indicative figures from public listings in late 2026 and exclude GST. See our carriage board price guide for sources and details.
Practical tips for owners
- Learn the basic chain so you can describe faults accurately to technicians
- Keep a board identity file with photos and versions of every board
- Stock low-cost parts that allow fast swap tests: cables, transfer boards
- Protect the whole chain with good earthing, stable power and surge protection
- Keep the carriage clean, dry and cool
- Insist on root cause analysis after every major failure
Example: following the chain
An 8-head 16 ft machine starts dropping all heads intermittently. The operator reports it happens near the left end. The technician starts with the scope: all heads, position-dependent. That points to the data link or carriage power cable in the cable chain rather than individual heads or the driver section. Inspection reveals a worn power cable inside the chain near the left end, causing brief voltage loss to the carriage. Replacing the cable fixes the problem. The mainboard, head board and driver section were never at fault. Following the chain saved a costly board replacement.
How data and power travel through the chain during one print pass
It helps to follow a single pass of the carriage across a 16 ft machine. Before the pass starts, the RIP has already converted the artwork into dot data for each colour and each head. The print control software sends this data to the mainboard, which stores it in memory so printing is not interrupted by small delays on the PC. When the mainboard commands the carriage motor to move, it reads the encoder strip to know the carriage position to a fraction of a millimetre. At the right positions, it streams the data for that pass through the main data link to the head carriage board.
The head carriage board receives the stream, separates it into data for each head and passes it on in step with the encoder timing. At the same moment, the driver section delivers a carefully shaped voltage pulse to every nozzle that needs to fire. The heads jet ink onto the flex, the carriage reaches the end of its travel, the media advances, and the cycle repeats thousands of times in a single job. Every link has to perform perfectly on every pass. A fault anywhere in this sequence shows up in the print, and the type of defect tells you which link is struggling.
Where the encoder and sensors fit in
The encoder strip and its reader are not boards, but they are part of the chain because they provide timing. If the encoder strip is dirty with ink mist or dust, the mainboard and head board receive wrong position information. The result can look like a board fault: blurred printing, colour misregistration, “position” errors or the carriage stopping. Media sensors, origin sensors and crash sensors also report to the mainboard; a faulty sensor can stop the machine or prevent printing. Before suspecting expensive boards, technicians check the encoder strip, reader and sensors. Our guide to flex printer encoder strip and sensor symptoms explains these checks.
How the chain differs between board systems
Not every flex machine divides the chain in the same way. BYHX, Hoson, Senyang and machine-specific systems arrange functions differently:
| Design approach | What it means | Repair implication |
|---|---|---|
| Integrated carriage board | Head data handling and driver circuits on one board | A driver fault may need the whole carriage board replaced or repaired |
| Separate driver or transfer boards | Driver or protection circuits on small boards above heads | Single-channel faults can often be fixed by replacing a small board |
| Mainboard with heater and motor drivers | Mainboard handles high-current loads directly | Heater or motor faults can damage the mainboard |
| Separate motor drivers | Dedicated driver modules for motors | Motor faults are easier to isolate and cheaper to fix |
Ask your machine supplier for a simple block diagram of your machine’s electronics, or ask a technician to sketch one during a service visit. Keep it with your board identity file. When a fault happens, this one page saves hours of guesswork.
Describing faults accurately to your technician
Technicians often diagnose by phone before visiting. The more precisely you describe the symptom in chain terms, the faster they can bring the right parts. Useful details include:
- Does the fault affect the whole machine, all heads, a group of heads or one head?
- Does it happen at a particular carriage position, time of day or type of job?
- What error messages appear in the software, word for word?
- Did anything change recently: head replacement, cable change, software update, power event or ink change?
- Has the fault got steadily worse or does it come and go?
- Any smell, sound, heat or visible damage?
A message such as “heads 5 to 8 print weak after 30 minutes of solid printing, settings are correct, no errors” points the technician straight towards the driver section serving those heads or the carriage power. “The machine is not printing properly” tells them almost nothing.
Upgrades and the chain
When owners plan upgrades, such as moving from 4 to 8 heads or from KM512i to KM1024i, every link in the chain must support the change. A new head board may need a matching mainboard, firmware and software version, a higher-capacity data link and a larger power supply. Driver sections must suit the new heads’ voltage and waveform. Treat an upgrade as a chain project, not a single board purchase. Our article on head driver board compatibility explains the matching rules.
Further reading: A flex machine mainboard plays a role similar to a computer motherboard, coordinating every other part of the system.
Key takeaways
- Flex machine electronics form a chain from PC to mainboard to head board to driver section to heads, fed by power supplies.
- Mainboard faults usually affect the whole machine; head board faults affect data and detection; driver faults affect firing energy.
- Symptom scope (machine, all heads, group or one head) is the best guide to where the fault lies.
- Faults can spread along the chain, so find the root cause before replacing parts.
- Cheap spares such as cables and transfer boards make diagnosis faster and safer.
Need help understanding the electronics on your flex machine? Unified Engineering Dynamics can help you identify boards, diagnose faults and source compatible spares.
More in the flex head driver board series
- Flex Machine Head Driver (Fire) Board Explained
- Head Driver Board Failure Signs
- Why a Bad Driver Board Can Kill a New Konica Head
- Konica 512i Head Voltage Settings
- Head Driver Board Compatibility: Konica, Ricoh, Seiko
- Head Driver Board Repair vs Replacement
- Power Fluctuation, Stabilizer and Earthing Guide
- Board Cooling and Dust: Preventing Overheating
Related reading on our site: Konica KM512i printhead price and lifespan, KM512i vs KM1024i printheads, flex printer mainboard and head board buyer checks, data and printhead cable handling and the flex printing machine maintenance checklist.
Running an Epson-head eco-solvent machine as well? Our sister series starts with the eco-solvent head carriage board guide and the complete guide to eco-solvent printer electronics.
Frequently Asked Questions
What is the difference between the head board and the head driver board?
The head board handles print data and timing for each head, while the head driver board supplies the voltage and energy that make the heads fire. On some machines they are combined on one board.
Which board fails most often on flex machines?
It varies, but carriage electronics, including head boards and driver sections, face more stress from ink, heat and motion than the mainboard, so they often fail more frequently.
Can a mainboard fault cause heads not to be detected?
Yes. If the mainboard cannot send data or power to the carriage correctly, all heads may appear undetected. Check the data link and carriage power too.
Why does a fault on one head sometimes damage another?
A shorted head can damage the driver channel, which then applies abnormal voltage to the next head connected. Cables can also carry faults between parts.
Should I replace the mainboard if the machine won’t start?
Not immediately. Check power supplies, communication cables, software and fuses first. Mainboard replacement should follow proper diagnosis.
How do technicians find which board is faulty?
They study the symptom scope, test upstream links, use swap tests with known good parts and measure voltages, working systematically along the chain.
Are power supplies part of the electronics chain?
Yes. Every board depends on stable DC power. A failing supply can cause symptoms that look like board faults anywhere in the chain.
Is it useful for owners to understand the electronics chain?
Yes. Owners who understand the chain describe faults more accurately, which leads to faster, cheaper repairs and fewer unnecessary purchases.
Can a dirty encoder strip look like a board fault?
Yes. Wrong position information can cause blurred printing, misregistration and position errors that resemble mainboard or head board problems. Clean and check the encoder first.
Is the driver section always a separate board?
No. On some systems it is integrated into the head carriage board; on others it sits on separate driver or transfer boards above the heads. Identify your design before ordering parts.