Direct answer: A head board usually burns after a Konica head change for one of six reasons: the head cable was inserted crooked, one pin off or with power on; the new or refurbished head had an internal short; the old head that was removed had already damaged the board’s driver section; the wrong head voltage was entered (often the previous head’s value or a default); ink or cleaning fluid reached connectors during the change; or a surge or earthing fault coincided with power-up. You avoid it by testing heads and cables before connection, switching off completely before touching cables, entering each head’s label voltage before printing, keeping the work area dry and powering up in stages while watching for warning signs.
A Konica head change is one of the riskiest moments for a flex machine’s electronics, and most burnt boards trace back to a few avoidable mistakes.

Table of Contents
A burnt head board after a head change is one of the most painful failures in a flex unit. You have just paid for a new Konica KM512i or KM1024i head, and now the board is dead, the new head may be damaged, and production has stopped. This guide explains why it happens and gives a step-by-step routine to prevent it. For background, read our guides on the head carriage board and Konica KM512i head price and lifespan.
Why head changes are a high-risk moment
During normal printing, the head, cable and board work as a stable system. A head change disturbs everything at once: connectors are opened, a new head with unknown history is introduced, settings change, ink lines are opened and the machine is powered up in a new configuration. If anything is wrong, the head board’s driver section is often the first part to fail because it supplies the voltage pulses that fire the head.
Cause 1: Wrong cable insertion
Konica heads connect through flat flexible cables with closely spaced contacts. When a cable is inserted at an angle, shifted by one position, or not fully seated, signal and power lines can touch the wrong contacts. When power is applied, voltage can flow into circuits that cannot tolerate it.
How to avoid it
- Insert cables only with the machine fully switched off and unplugged
- Align the cable straight with the connector before pushing in
- Check that the cable is fully seated along its full width
- Engage the connector lock
- Use good lighting and, if needed, a magnifier to inspect insertion
- Have a second person check before power-up
Cause 2: A shorted new or refurbished head
Not every head is perfect. A new head can be damaged in transit; a refurbished or “pulled” head may have internal damage; a head stored without proper sealing can have ink residue on its connector. Connecting a shorted head to a board can burn the driver section immediately.
How to avoid it
- Buy heads from reliable suppliers with clear warranty terms
- Inspect the head connector for ink, corrosion or damage before fitting
- Ask your technician to test the head electrically before connection where possible
- Be cautious with very low-priced heads, as price differences in the market can indicate refurbished or used stock. Listings in India range widely, as discussed in our KM512i price guide
Cause 3: The old head already damaged the board
This cause is often overlooked. If the old head failed because of an internal short, it may have already damaged the board’s driver section before it was removed. The board may still appear to work partially, or the damage may only become obvious when a new head is connected. The new head then receives abnormal voltage and fails, and the cycle continues.
How to avoid it
- When a head fails suddenly (especially with burnt smell or blown fuses), have the board channel tested before fitting a new head
- Check other heads on the same board for unusual behaviour
- Do not fit a new head to a channel that showed abnormal symptoms until tested
Our guide to head board failure symptoms describes warning signs that suggest a damaged channel.
Cause 4: Wrong head voltage
Each Konica head has an individual drive voltage printed on its label or test sheet. When a head is replaced, the new head’s voltage must be entered for that position. Common mistakes include:
- Leaving the old head’s voltage in the software
- Entering the value for the wrong head position
- Typing a wrong digit
- Using a board’s default value
- Raising voltage to “improve” weak printing
Too high a voltage overheats the head and stresses the driver section. Repeated overvoltage can burn driver components over time, even if failure is not immediate.
How to avoid it
- Keep a head register with serial number, position and voltage
- Enter the new value before the first nozzle check
- Double-check entries with a second person
- Never exceed label values to fix print problems; find the real cause
Cause 5: Ink or cleaning fluid in connectors
Head changes involve opening ink lines, removing dampers and handling heads that may still contain ink. Drips can land on connectors or the board. Cleaning solution used to wipe the head plate can also reach electronics.
How to avoid it
- Cover the board and connectors with lint-free cloth during ink work
- Drain or clamp ink lines before removing heads
- Keep cleaning bottles away from the carriage
- Inspect and dry connectors before inserting cables
- Wait for any solvent to evaporate before power-up
Our article on solvent ink leaks and carriage board damage covers this risk in detail.
Cause 6: Power surges and earthing at power-up
Power-up is a stressful moment for electronics. If input voltage is unstable, earthing is poor, or the machine shares a circuit with heavy equipment, a surge at power-up can damage a board, particularly one already weakened.
How to avoid it
- Power up through a properly rated stabiliser or servo
- Ensure good earthing between machine, PC and mains
- Avoid power-up during known grid instability (for example, just after a power cut returns)
- Switch on the PC and machine in the order recommended by your board supplier
Safe Konica head change routine
Use this routine every time a head is changed:
- Diagnose first: Confirm the old head is faulty, and check the board channel if the head failed suddenly.
- Prepare: Have the new head, its voltage value, new cable (if needed), tools, ESD strap and cloths ready.
- Record: Note current settings, head positions and voltages.
- Power off: Switch off and unplug. Wait several minutes.
- Protect electronics: Cover board and connectors.
- Remove old head: Disconnect cable straight, remove ink connections carefully, remove head.
- Inspect: Check cable and connector for damage, burn marks or ink. Replace the cable if in doubt.
- Fit new head: Mount mechanically, connect ink, check for leaks.
- Connect cable: Insert straight and fully, engage lock, have a second person check.
- Dry check: Ensure no ink or fluid near connectors.
- Power up: Through stabiliser, in correct order. Watch and smell for anything unusual.
- Enter voltage: Set the new head’s voltage before any printing.
- Heat and test: Let heads reach temperature, then run nozzle check.
- Calibrate: Align the new head and run a test print.
- Log: Record the change in your maintenance log.
Warning signs at power-up
| Sign | Action |
|---|---|
| Burnt smell or smoke | Switch off immediately; do not restart |
| Fuse blows | Do not replace fuse and retry; find the short |
| New head not detected | Switch off; check cable insertion |
| Head temperature error on new head | Switch off; check cable and connector |
| Other heads start failing | Switch off; possible board or power issue |
| Random firing on new head | Check voltage entry and cable |
The most important rule: if something burns, do not keep retrying. Each attempt can damage more parts.
What to do after a board has burnt
- Switch off and keep the machine off.
- Photograph the board, head connector and cable for records and warranty.
- Have a technician test the new head, the old head and all cables.
- Replace any damaged cables.
- Repair or replace the board, following our carriage board replacement checklist.
- Identify the root cause before fitting the next head.
The cost of a burnt board cycle
| Item | Impact |
|---|---|
| Carriage board repair or replacement | Tens of thousands of rupees |
| Damaged new head | One of the most expensive spares on the machine |
| Cables and adapters | Lower cost, but often overlooked |
| Downtime | Days of lost production, especially in peak season |
| Customer impact | Delayed orders, lost repeat business |
A disciplined head change routine costs nothing extra and prevents most of these losses. For pricing context, see our carriage board price guide.
Keep a head register
A head register is a simple record that prevents most voltage mistakes during a Konica head change. Keep it in a notebook or spreadsheet near the machine.
| Position | Colour | Head serial | Label voltage | Installed | Source / warranty | Notes |
|---|---|---|---|---|---|---|
| 1 | Cyan | (from label) | (from label) | Date | Supplier, warranty period | New |
| 2 | Magenta | … | … | … | … | … |
| 3 | Yellow | … | … | … | … | … |
| 4 | Black | … | … | … | … | … |
Before every head change, compare the software’s voltage settings with the register. After the change, update the register immediately. Photograph each head’s label before installation, because labels can become unreadable after ink exposure.
Buying heads: questions that protect your board
- Is the head new, refurbished or pulled from another machine?
- Does it come with its voltage label or test sheet?
- Has it been tested, and how?
- What warranty applies, and does it cover installation damage?
- Is it the correct drop size and variant for your machine (for example 14 pl or 42 pl KM512i)?
- Was it stored sealed, and is the connector clean?
Indian market prices for Konica heads vary widely, from very low offers to premium prices for new heads with warranty. A head that is unusually cheap may be refurbished or used, which increases the risk of internal shorts. A careful purchase is part of avoiding a burnt head board.
Case example: breaking the burnt-board cycle
A flex unit replaced a failed magenta head with a new one. On power-up, the new head was not detected and a burnt smell appeared. The technician replaced the carriage board, and the unit fitted another new head. Within a day, the second new head failed too. Only then was the original magenta head cable inspected: it had a small burn mark and a short between two lines, created when the first head failed. Each new head and board had been damaged by the same faulty cable. Once the cable was replaced and the board channel repaired, the problem ended. The unit lost two heads, one board and five days of production. Inspecting and replacing the cable at the first Konica head change would have prevented almost all of that loss.
Train everyone who touches the machine
In many units, more than one person handles heads: the owner, a senior operator, a night-shift operator or a visiting technician. Make sure everyone follows the same routine. A short training session, a laminated checklist and a rule that no head change happens without recording voltages are simple steps that protect expensive parts. Include the routine in your maintenance checklist and review it before every peak season.
Staged power-up for extra safety
Some technicians use a staged power-up after a Konica head change, especially when the previous head failed suddenly. In this approach, the machine is first powered with the new head disconnected to confirm that the board and remaining heads behave normally and that no fuse or burnt smell appears. The machine is then switched off, the new head’s cable is connected with power off, and the machine is powered again while watching closely. This adds a few minutes but can reveal a damaged board channel before it reaches the new head. Follow your board supplier’s guidance, as not all systems behave the same way when a head is missing.
Environmental checks before a head change
- Avoid head changes during thunderstorms or when the grid is unstable
- Make sure the room is dry and not excessively humid
- Check that the stabiliser or servo is working normally
- Confirm that the earth connection is intact
- Make sure there is enough light to inspect cable insertion properly
These checks are easy to overlook in a rush but address the power and earthing risks that can damage a board at the moment of power-up.
Finally, record every Konica head change in the maintenance log with the date, the head serial number, the voltage entered, who did the work and the result of the first nozzle check. Over time, this history shows which positions fail more often and helps you spot cable, board or ink system problems early.
Further reading: Most burnt driver sections are caused by a short circuit somewhere in the head, cable or connector.
Key takeaways
- Most burnt head boards after a Konica head change come from cable insertion errors, shorted heads, prior board damage, wrong voltage, ink contamination or power surges.
- Always switch off and unplug before handling cables.
- Test the board channel when a head failed suddenly, before fitting a new head.
- Enter the new head’s label voltage before printing and keep a head register.
- If anything burns, stop and find the root cause before trying again.
Replacing a Konica head and want to avoid a burnt board? Contact Unified Engineering Dynamics for genuine heads, cables, compatible boards and guidance on safe installation.
More in the flex carriage board series
- Flex Machine Head Carriage Board Explained
- Konica Head Board Failure Symptoms
- Hoson vs Senyang vs BYHX Carriage Boards for Konica
- 4-Head vs 8-Head Carriage Board Upgrade
- Solvent Ink Leaks and Carriage Board Damage
- Head Data Cable vs Carriage Board Fault
- Flex Carriage Board Replacement Checklist
- Flex Machine Carriage Board Price in India
- Flex Carriage Board Connectors: Handling Rules
Related reading on our site: Konica KM512i printhead price and lifespan, KM512i vs KM1024i printheads, flex printer mainboard and head board buyer checks, data and printhead cable handling and the flex printing machine maintenance checklist.
Running an Epson-head eco-solvent machine as well? Our sister series starts with the eco-solvent head carriage board guide and the complete guide to eco-solvent printer electronics.
Frequently Asked Questions
Why did my head board burn right after fitting a new Konica head?
Common causes are crooked or misaligned cable insertion, a shorted head, prior damage to the board from the old head, wrong voltage, ink in connectors or a surge at power-up.
Can a new head be damaged by a faulty board?
Yes. A damaged driver section can apply abnormal voltage to the new head. Test the board channel before fitting a new head if the old head failed suddenly.
Should I replace the head cable during every head change?
Not always, but inspect it carefully. Replace it if there is any creasing, burn mark, ink contamination or if the old head failed with a short.
Where do I find the correct Konica head voltage?
It is printed on the head’s label or supplied on a test sheet. Record it in your head register and enter it for the correct position before printing.
Is it safe to replace a blown fuse and try again?
No. A blown fuse indicates a short or overload. Find and fix the cause first, or you risk damaging more parts.
Can refurbished heads cause board damage?
They can if they have internal damage. Buy from reliable suppliers with testing and warranty, and inspect connectors before fitting.
Should I change all head cables when one Konica head fails?
Not necessarily. Replace the failed head’s cable if it shows any damage or if the head failed with a short. Inspect the other cables and replace any that look worn.
How soon after a head change should I calibrate?
Calibrate after the new head reaches operating temperature and passes a nozzle check. Run head alignment and bi-directional calibration before production printing.