Flex Printing

Head Board Failure Symptoms on Konica Flex Machines: Head Not Detected, Missing Colours and Random Firing

Flex Head Board Failure: 8 Konica Symptoms to Know

Direct answer: The most common head board failure symptoms on a Konica solvent flex machine are: one or more heads shown as “not connected” or “not detected” in the software, a full colour missing from the print even though nozzle checks look partly normal, random dots or lines firing in blank areas, weak or uneven jetting across a group of heads, head temperature errors, and faults that appear only after the machine warms up or when the carriage reaches a certain position. These signs can also come from head cables, the high-speed data link, the printhead itself, the mainboard or poor earthing, so the right approach is to observe the pattern carefully, check simple causes first and confirm with a known good part before buying a new board.

Recognising flex head board failure early, and telling it apart from cable, ink or head problems, can save a Konica flex unit days of downtime and a costly wrong purchase.

Flex Head Board Failure: 8 Konica Symptoms to Know
Flex Head Board Failure: 8 Konica Symptoms to Know

This guide is for owners, operators and technicians running 10 ft and 16 ft solvent flex machines with Konica KM512i or KM1024i heads on BYHX, Hoson or similar board systems. It explains what each symptom usually means and what to check, without asking you to do risky electronic repairs yourself. If you are new to the topic, start with our article on what the flex machine head carriage board does.

Why flex head board failure patterns matter more than single errors

On an eight-head flex machine, a single board fault can look very similar to a single head fault or a cable fault. The key is to study the pattern: how many heads are affected, whether the problem follows a head when you swap positions, whether it changes with temperature or carriage position, and whether it started after a specific event. Technicians call this “fault isolation”. The more precisely you describe the pattern, the faster and cheaper the repair.

A simple rule of thumb that works on most machines:

  • One head affected: think printhead, head cable or adapter board first.
  • A group of heads affected (for example heads 1–4 or 5–8): think a section of the carriage board, a driver section, or one of two carriage boards.
  • All heads affected: think the carriage board as a whole, the data link from the mainboard, the power supply to the carriage, or the mainboard.

Symptom 1: Head not detected or “head not connected”

Most board systems check each head at start-up. If a head does not respond, the software shows it as missing, disconnected or in error. On BYHX-based systems you may see the head position highlighted or a message that a head cannot be found; on other systems the head may simply disappear from the head list.

What it usually means

PatternMost likely causes
One head not detected, others normalHead cable not fully inserted or damaged, adapter board fault, head itself faulty, one channel on the board damaged
Several heads in one group not detectedSection of the carriage board, a connector between boards, power to that section
All heads not detectedData link from mainboard (fibre or cable), carriage power supply, carriage board, firmware mismatch
Heads appear and disappear randomlyLoose connector, cable worn in cable chain, earthing noise, heat-sensitive fault

What to check first (power off)

  1. Switch off the machine and wait a few minutes.
  2. Check that each head cable is straight, fully inserted and locked at both ends.
  3. Look for ink or corrosion on connectors.
  4. Check the data link connector at the carriage and at the mainboard. Fibre connectors must be clean and fully seated.
  5. Restart and see whether the pattern changes.

If one head is missing, a technician can swap that head’s cable or swap the head’s position with a working head (with correct voltage settings) to see whether the fault follows the head, the cable or the board channel. Our guide on head data cable vs carriage board faults explains this swap method in detail.

Symptom 2: A full colour missing from the print

On a four-head machine each colour has one head. If cyan disappears completely, the cyan head, its cable or its board channel has stopped firing. On an eight-head machine with two heads per colour, you might see the colour printing at half density or with alternating bands.

Separate ink problems from electronic problems

A missing colour is often an ink supply problem, not an electronic one. Before blaming the head board, check:

  • Ink level, ink pump and filter for that colour
  • Damper or sub-tank condition and air in the line
  • Negative pressure settings, if your machine uses a negative pressure system
  • Capping station and wiper condition

If the nozzle check shows the head trying to fire (some nozzles, faint lines or misdirected lines), the electronics are at least partly working. If the head shows completely blank even after successful cleaning and ink flows from the head during purging, the problem is more likely electronic: no data or no drive voltage reaching that head.

Symptom 3: Random firing, dots or lines in blank areas

Random firing looks like unwanted dots, short lines or streaks in areas that should be white. On large flex prints it may appear as scattered specks across a hoarding or as thin vertical lines at fixed positions.

Possible causes

  • Electrical noise: poor earthing, high static from flex rolls, or interference on the data cable.
  • Damaged cable: a cracked conductor or a short between neighbouring lines in a head cable.
  • Board fault: a failing driver component or a damaged data buffer on the carriage board.
  • Head fault: an internally damaged head can fire some nozzles uncontrollably.
  • Software or RIP settings: wrong head mapping or step settings can mimic random firing patterns.

Random firing that gets worse in dry winter weather or when unwinding fresh flex rolls often points to static and earthing. Random firing locked to one head that follows the head when swapped points to the head. Random firing on several heads at once, with no static link, points more towards the board or data link.

Symptom 4: Weak or uneven jetting on a group of heads

Weak jetting shows as faded colours, thin lines in the nozzle check, banding or deflected nozzles. If it affects a group of heads together, the drive voltage supplied to that group may be low or unstable.

ObservationPoints towards
Weak jetting on one head onlyHead wear, wrong voltage entered for that head, partial blockage
Weak jetting on all heads, improves after warm-upHead temperature too low, heater or temperature control problem, ink viscosity
Weak jetting on a group of heads, voltage settings correctDriver section on the carriage board, carriage power supply, connector between boards
Weak jetting worsens over a shiftOverheating of board or power supply, failing fan, dust on heat sinks

Never “fix” weak jetting by raising voltages far above the head label value. It may work briefly but can shorten head life and stress the board. Our guide on burnt head boards after a Konica head change explains why voltage discipline matters.

Symptom 5: Head temperature errors

Solvent machines heat the heads or ink to keep viscosity stable. If the carriage board cannot read the head temperature or cannot control the heater, you may see temperature errors, heads that never reach target temperature, or heads that overheat.

Common causes include a damaged thermistor connection, a head cable not fully inserted, a faulty heater circuit on the board, or a failed fuse or protection component. If the error affects one head, check that head’s connection. If all heads show temperature errors together, check the carriage power supply and the board.

Symptom 6: Faults that appear after warm-up

Some machines print perfectly for the first half hour and then start dropping heads or printing random lines. This is a classic sign of a heat-sensitive fault. Candidates include a cracked solder joint, a failing capacitor or driver chip, a connector with weak contact pressure, or a power supply that sags when hot.

To help your technician, note how long the machine runs before the fault appears, whether it disappears after cooling, and whether the carriage fan is working. Dust buildup and a dead fan are surprisingly common and cheap to fix.

Symptom 7: Faults at a specific carriage position

If heads drop out or errors appear only when the carriage reaches a certain point, for example near the far end of a 16 ft machine, suspect the cable chain. The data link, power cable or head-related wiring may be stressed or cracked at that point of travel. Fibre-optic cables are especially sensitive to tight bends.

Move the carriage slowly by hand with the power off and inspect the cable chain for kinks, worn insulation or loose clips. This is a mechanical problem that can easily be mistaken for a board failure.

Symptom 8: Burnt smell, visible damage or blown fuses

A burnt smell from the carriage, discoloured components, melted connector plastic or repeatedly blown fuses are serious signs. Switch the machine off immediately and do not keep restarting it. Repeated power-on attempts with a short in the system can damage the mainboard, power supply and new heads.

In these cases a technician should inspect the board, the heads and the cables together. It is common for a shorted head to burn the board’s driver section, and for a damaged board to then destroy the next head fitted. Breaking this cycle requires testing each part before reconnecting.

Symptoms that look like head board failure but are not

Many boards are replaced unnecessarily. Before ordering, rule out these common look-alikes:

Look-alikeHow it showsHow to tell
Blocked nozzles or air in ink lineMissing lines, colour missingInk does not flow properly during purge; improves after cleaning
Encoder strip dirtyMisaligned or blurry print, position errorsClean the encoder strip; check encoder sensor
Wrong RIP or head settingsStrange banding, colours in wrong placeProblem appears after software change; check head mapping
Mainboard faultNo heads detected, no communicationCarriage does not initialise; PC connection errors
Earthing or staticRandom dots, intermittent errorsWorse in dry weather or with certain media

For more general troubleshooting, see our flex printing machine problems and solutions guide and the encoder strip troubleshooting guide.

A safe diagnostic sequence for operators

The following steps are safe for trained operators and help narrow down the problem before a technician arrives:

  1. Record the exact error message and take photos of the software screen.
  2. Print a nozzle check and photograph it.
  3. Note how many heads and which positions are affected.
  4. Switch off, wait, and inspect cables, connectors and the cable chain for damage or ink.
  5. Clean visible dust and ink around connectors with power off.
  6. Reseat connectors carefully, then restart.
  7. Check whether the problem changes with warm-up time or carriage position.
  8. Check earthing and input voltage if random faults occur.

Leave cable swaps between heads, voltage changes, board removal and component repair to a trained technician. Swapping cables or heads with wrong voltage settings can damage good parts.

What information helps your supplier match a replacement

If testing confirms that the head board is faulty, your supplier needs:

  • Photos of the board label, version number and both sides of the board
  • Machine model, print width and head count
  • Head type (KM512i or KM1024i) and drop size
  • Mainboard brand and version
  • Software name and version

Read our Hoson vs Senyang vs BYHX carriage board compatibility guide before ordering, because the wrong version can waste days in peak season.

A simple symptom record sheet

Technicians repeatedly say that the best help an owner can give is a clear record of what happened. Keep a printed sheet near the machine and fill it in whenever a head or board problem appears. Over weeks, the sheet also reveals patterns that a single visit cannot.

FieldExample entry
Date and time12 Nov, 4:40 pm, second hour of shift
Job and mediaElection hoarding, 340 gsm frontlit flex
SymptomHead 6 not detected, magenta at half density
Error messageScreenshot saved as photo 1
Heads affectedOne head (position 6)
TriggerAfter power cut and restart
Action takenPower off, reseated cable, restarted
ResultHead detected again; monitoring

When the same head position appears on the sheet three times in a month, you have strong evidence for a cable, adapter or board channel problem at that position, even if each event cleared after a restart.

How seasons change the symptoms

Indian conditions change sharply through the year, and so do flex head board failure patterns. In the dry winter months, static from unwinding flex rolls increases random firing and intermittent dropouts. During the monsoon, humidity and lightning-related surges bring more sudden failures and corrosion at connectors. In peak summer, high shed temperatures make heat-sensitive faults appear earlier in the shift. Knowing this helps you separate a seasonal environmental cause from a genuinely failing board and plan checks such as earthing tests before winter and surge protection before the monsoon.

Further reading: Static from flex rolls is a real factor in random firing; this explainer on electrostatic discharge describes how it damages electronics.

Key takeaways

  • Head board failure symptoms include heads not detected, missing colours, random firing, weak jetting, temperature errors and heat- or position-related faults.
  • The number of heads affected is the most useful clue: one head, a group or all heads.
  • Ink supply, encoder, earthing and software problems often mimic board failure.
  • Burnt smells and blown fuses mean stop immediately and test heads, cables and board together.
  • Good records and photos make diagnosis faster and replacement accurate.

Facing head errors on your Konica flex machine? Share your machine details, error screenshots and nozzle checks with Unified Engineering Dynamics, and we will help you identify whether the head board, cable or printhead is at fault.

More in the flex carriage board series

Related reading on our site: Konica KM512i printhead price and lifespan, KM512i vs KM1024i printheads, flex printer mainboard and head board buyer checks, data and printhead cable handling and the flex printing machine maintenance checklist.

Running an Epson-head eco-solvent machine as well? Our sister series starts with the eco-solvent head carriage board guide and the complete guide to eco-solvent printer electronics.

Frequently Asked Questions

Why does my flex machine show one head as not connected?

The most common causes are a loose or damaged head cable, a faulty adapter board, a damaged board channel or a faulty head. Check the cable connection with power off first, then ask a technician to swap cables or positions to locate the fault.

Can a bad head board cause random dots on flex prints?

Yes, a failing driver or data section can cause random firing. However, poor earthing, static from flex rolls and damaged cables cause the same symptom, so check those before replacing the board.

All heads stopped working at once. Is it the head board?

Possibly, but also check the data link from the mainboard, the carriage power supply and the mainboard itself. A fault affecting every head usually originates upstream of the individual heads.

Should I increase head voltage to fix weak printing?

No. Set each head to the voltage on its label or test sheet. Raising voltage to compensate for weak printing can shorten head life and stress the board. Find the real cause instead.

Why do my heads drop out only after printing for an hour?

Heat-related faults are often caused by a cracked solder joint, a failing component, a loose connector or a dead carriage fan. Note the timing and check the fan and dust levels first.

Is it safe to keep restarting the machine after a burnt smell?

No. Switch off and keep it off. Repeated restarts with a short in the system can damage the mainboard, power supply and any new heads. Have a technician inspect it.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *