Eco Solvent Printing, Printheads

Head Voltage Settings on the Fire Board: Why Getting Them Wrong Shortens Head Life

Head Voltage Settings: Protect Printhead Life

Direct answer: Every Epson piezo printhead leaves the factory with its own voltage value or rank printed on its label, because no two heads respond identically to the same drive signal. The fire board (or firing section of the carriage board) uses the value entered in the print control software to set the drive amplitude for that individual head, so that all heads produce the intended drop size. If the value is set too high, the head is overdriven: drops are larger, the head and fire board run hotter, piezo elements and internal chips age faster, and misting and satellites increase. If it is set too low, drops are smaller and weaker, colours look pale, and nozzles may misfire. The safe practice is to read the value from each head’s label, enter it in the correct head position, save and verify it, record it, and never raise voltage to cover up clogging or ageing.

Correct head voltage settings are one of the simplest ways to extend printhead life.

Head Voltage Settings: Protect Printhead Life
Head Voltage Settings: Protect Printhead Life

Voltage settings are one of the most misunderstood parts of eco-solvent printer setup. Some operators never touch them; others raise them whenever prints look weak. Both approaches cause problems. This guide explains what the value means, how the firing circuit uses it, what happens when it is wrong, and how to manage it safely. It is part of our fire board series; for the basics see what is a fire board.

Why each head has its own voltage value

Piezo printheads are precision devices, but tiny manufacturing differences in piezo material, chamber dimensions and nozzle geometry mean each head ejects slightly different drop volumes at the same voltage. To compensate, the manufacturer measures each head and assigns a value or rank that tells the controlling electronics how much drive voltage that head needs to produce the standard drop. The value is printed on the head’s label, sometimes as a direct voltage figure and sometimes as a code that the board software interprets.

When the correct value is entered, all heads in a machine produce matching drop sizes, so colour density is consistent across heads and over time. When values are wrong or mismatched, one head prints darker or lighter than another, which shows as banding or colour differences between head zones.

How the fire board uses the value

The fire board generates a waveform with a defined shape. The voltage value sets the peak amplitude of that waveform for each head. In simple terms:

  • Higher amplitude makes the piezo element move further, ejecting a larger, faster drop.
  • Lower amplitude makes it move less, ejecting a smaller, slower drop.

The waveform shape (timing, rise and fall) is usually defined by firmware and print mode. The voltage value scales it for each head. Some systems also adjust amplitude automatically based on head temperature, because ink viscosity changes as the head warms. In such systems, the entered value acts as a baseline that the board adjusts around.

What happens when voltage is too high

EffectWhy it happensConsequence
Larger, faster dropsPiezo moves furtherHeavier ink laydown, longer drying, possible bleeding
More satellites and mistingDrops break up at higher velocityFuzzy edges, spray around text, dirty nozzle plate
Higher head temperatureMore energy per firing cycleFaster ageing of piezo elements and internal chips
Higher fire board temperatureAmplifier delivers more powerFaster ageing of transistors and capacitors; heat-related faults
Air ingestion riskStronger meniscus movementNozzle dropouts that need cleaning
Shortened head lifeCumulative stressEarlier replacement of an expensive head

The worst part is that overdriving can make prints look good at first: colours look strong and the nozzle check looks full. The damage accumulates silently until the head starts losing nozzles permanently or fails electrically.

What happens when voltage is too low

EffectConsequence
Smaller, slower dropsPale colours, weak solids, visible graininess
Unstable firingRandom missing nozzles, especially at high frequency
Drop placement errorsSlow drops are more affected by carriage speed and air movement, causing blur and banding
Colour mismatch between headsVisible density steps on multi-head machines

Low voltage is less damaging to the head than high voltage, but it reduces quality and often leads operators to run extra cleanings or raise ink limits in the RIP, which waste ink and time.

Common ways voltage settings go wrong

  • Not entered after a head change: the new head runs on the old head’s value.
  • Entered in the wrong position: on a double-head machine, head 1’s value goes into head 2’s field and vice versa.
  • Misread label: small print, smudges or confusion between similar characters.
  • Software reinstall or reset: settings return to defaults that do not match the installed heads.
  • Board replacement: a new board arrives with default values.
  • Deliberate increase: someone raises voltage to compensate for weak printing caused by clogging, an ageing head or ink starvation.
  • Copied from another machine: values taken from a “similar” printer instead of the actual heads.
  • Wrong head type selected: the board applies waveform and scaling for a different head or variant.

Getting head voltage settings right, step by step

The exact menus differ between Hoson, Senyang, BYHX and other systems, and some manufacturers restrict access to these settings with a password. The general procedure is:

  1. Read the label before installation. Photograph each head’s label clearly when it is out of the machine. Labels are often hard to see once installed.
  2. Identify head positions. Know which physical head is head 1, head 2 and so on in the software. Mark them if needed.
  3. Open the head settings. In the print control software, find the head parameter or voltage section. Use the manufacturer’s password if required.
  4. Confirm head type and variant. Make sure the correct head model is selected.
  5. Enter each value in the correct position. Double-check against your photos.
  6. Save and apply. Some systems require a restart.
  7. Verify. Reopen the settings to confirm values were saved.
  8. Test. Print a nozzle check and a colour test, and compare density between heads.
  9. Record. Write the head serial numbers and values in the machine log.

If the software shows values in a format that does not obviously match the label, ask your board supplier how to interpret it. Do not guess.

Should you ever adjust voltage away from the label value?

The label value is the starting point. Some technicians make small adjustments to balance density between heads or to suit a particular ink, especially on multi-head machines. Such adjustments should be:

  • Small, and within the range recommended by the board supplier or head manufacturer.
  • Based on measured density differences, not on general weakness.
  • Made only after ruling out clogging, ink supply problems and head ageing.
  • Recorded, so they can be reversed or repeated.

Raising voltage substantially to rescue an old or clogged head is not a fix. It speeds up the head’s decline and increases fire board stress. If a head needs much more voltage to print acceptably, it is time to investigate the cause or plan a replacement. Our article on weak colour causes helps identify the real reason for weak printing.

Voltage and ink

Different inks have different viscosity and surface tension. Board makers tune waveforms for typical inks of each type. When you change ink brand or type, drop formation can change, and colours may shift. The correct response is to check with your supplier whether a different waveform or print mode is recommended, re-calibrate and re-profile, rather than adjusting voltage to compensate. Using ink that is not approved for the head can damage the head regardless of voltage. See our eco-solvent ink guide for more on ink choice.

Voltage and temperature

Ink viscosity drops as temperature rises, which means the same voltage produces larger drops in a hot shop than in a cool one. Some board systems use the head’s temperature sensor to adjust drive automatically. Where this is not available, seasonal changes in Indian conditions, from cool winter mornings to hot summer afternoons, can affect print density. Stable room temperature helps. If your system has temperature compensation, make sure it is enabled and that the head temperature reading looks sensible.

Effects on the fire board

The fire board’s amplifier delivers power proportional to drive amplitude and firing frequency. Higher voltage settings, high-speed modes and heavy ink coverage together create the most heat. Over months, a board consistently run at high amplitude in a hot carriage will age faster. Components such as electrolytic capacitors and power transistors are particularly affected. Correct voltage settings are therefore part of protecting the board as well as the head. Our article on fire board cooling and dust explains how to keep temperatures in check.

Voltage settings on multi-head machines

On double-head and multi-head printers, voltage settings also control consistency between heads. Even with correct label values, slight differences may remain. Visible density steps between head zones can be caused by:

  • Swapped voltage values between head positions.
  • One head older or more worn than the other.
  • Different head batches with different characteristics.
  • Uneven ink supply to one head.
  • Alignment errors that look like density differences.

Check values and positions first, then ink supply, then alignment, before considering small balancing adjustments. Our guide to reducing banding and colour variation discusses related issues.

Voltage, print modes and drop sizes

Many board systems offer several print modes, such as production, standard and high quality, and some support variable drop sizes, where small, medium and large drops are mixed to improve gradients. Each mode may use a different waveform, and the voltage value scales all of them for the head. This has two practical consequences:

  • Do not judge voltage on one mode only. A head that looks right in production mode may show satellites in a high-frequency mode if voltage is too high, or weak small drops in a quality mode if it is too low. After setting voltage, test the modes you actually use.
  • Do not use voltage to change the look of a mode. If a mode prints too dark or too light, adjust ink limits, linearisation or the colour profile in the RIP rather than voltage. Voltage is a head calibration, not a colour control.

If your supplier recommends specific modes for your ink and media, use those as your baseline and build ICC profiles for them. Our guide to running and reading nozzle checks helps you assess firing quality in each mode.

A simple voltage record template

Keep a record like the one below in your machine log, and update it whenever a head, board or software installation changes.

FieldHead 1Head 2
Head model and variante.g. i3200 eco-solvente.g. i3200 eco-solvent
Head serial numberFrom labelFrom label
Label voltage value or rankFrom labelFrom label
Value entered in softwareAs enteredAs entered
Reason for any difference from labelIf adjustedIf adjusted
Date installed and by whom
Board brand, model, versionFrom board label
Firmware and software versionFrom software

With this record, anyone servicing the machine can verify settings in minutes, and a software reinstall or board change never leaves you guessing.

Access control: who should change voltage settings

Because voltage settings affect expensive heads directly, access should be limited. Good practice:

  • Only trained technicians or the shop owner change voltage settings.
  • Operators can view, but not change, the values.
  • Any change is recorded with date, reason and old and new values.
  • The machine log contains the label values for every installed head.

Many manufacturers protect these settings with passwords for exactly this reason. If your software allows anyone to change them, set a clear rule in the shop.

Signs that voltage may be set wrongly

Even without opening the software, the print can tell you that voltage settings deserve a check:

  • Fuzzy edges and spray around small text that appeared after a head change, board change or software reinstall.
  • One head printing visibly darker or lighter than the other on a double-head machine.
  • Nozzle plate getting dirty with ink mist faster than before.
  • Pale solids and grainy gradients that cleaning does not improve.
  • The carriage area or board running warmer than usual during heavy printing.
  • Head life noticeably shorter than previous heads on the same machine.

None of these prove the voltage is wrong, but each is a reason to compare the software values with the head labels before looking further. It takes a few minutes and is free.

Voltage settings checklist

#CheckDone
1Label value photographed for each head before installation☐
2Head positions identified and marked☐
3Correct head type and variant selected in software☐
4Value entered for each head in the correct position☐
5Settings saved, restarted if required, and verified☐
6Nozzle check and colour density test passed☐
7Values and head serials recorded in machine log☐
8Settings rechecked after any software reinstall or board change☐

Further reading: Head voltage controls how strongly the piezoelectric element flexes, which is why values are set per head.

Key takeaways

  • Each head’s voltage value compensates for manufacturing differences so all heads print the intended drop size.
  • The fire board uses the value to set drive amplitude for each head.
  • Too high a value overdrives the head and the fire board, causing misting, heat and shorter life; too low causes pale, unstable printing.
  • Read values from labels, enter them in the correct positions, verify and record them; recheck after head changes, board changes and software resets.
  • Do not raise voltage to hide clogging or ageing; find the real cause.

If you are unsure whether your head voltage settings are correct, or want help balancing a multi-head machine, the Unified Engineering Dynamics team can check your settings and guide you through safe adjustment.

More in the fire board series

Related: our head carriage board series starts with Eco-Solvent Head Carriage Board Explained, and covers head cable vs carriage board fault finding and the carriage board replacement checklist.

Related: our main board series covers main board functions and failure points, main board failure symptoms, the main board replacement checklist and how lightning, surges and earthing faults damage main boards.

For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.

Frequently Asked Questions

Where do I find the voltage value of my printhead?

It is printed on the head’s label, either as a voltage figure or as a code. Photograph it before installation, because the label can be hard to read once the head is fitted.

What happens if I set the head voltage too high?

The head is overdriven. Drops become larger and faster, misting increases, and both the head and fire board run hotter, which shortens their life.

Can I increase voltage to fix weak printing?

It is not recommended. Weak printing usually comes from clogging, ink supply problems or an ageing head. Raising voltage masks the problem and accelerates wear.

Do I need to re-enter voltage after replacing the carriage board?

Yes. New boards often have default values. Re-enter and verify the correct values for each head.

Why does one head print darker than the other on my double-head machine?

Possible causes include swapped voltage values, different head age or batch, uneven ink supply or alignment issues. Check values and positions first.

Should operators be allowed to change voltage settings?

Ideally no. Limit changes to trained technicians or the owner, and record every change.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *