Eco Solvent Printing, Printheads

Fire Board Compatibility: Matching Board Version to i3200, XP600 and DX5 Heads

Fire Board Compatibility for i3200, XP600 & DX5 Heads

Direct answer: A fire board (or carriage board with an integrated firing circuit) is designed for a specific head family, so an i3200 board will not drive an XP600 head and an XP600 board will not drive a DX5 head. Beyond head family, compatibility also depends on head variant (for example i3200 eco-solvent versus water-based or UV variants), number of heads, board brand and kit generation, firmware and waveform files, connector and adapter type, and any manufacturer authorisation. Even a board for the right head can fail to work, or drive the head incorrectly, if it does not match the mainboard and firmware of your machine. Always order by board brand, model and version confirmed from photos, plus head type, variant and count.

Fire board compatibility is decided by the head family, the waveform and the firmware, not by the printer brand.

Fire Board Compatibility for i3200, XP600 & DX5 Heads
Fire Board Compatibility for i3200, XP600 & DX5 Heads

This guide explains each compatibility factor, the specific considerations for i3200, XP600 and DX5 heads, the risks of mismatches, and how to confirm the right board. It is part of our fire board series; for background see what is a fire board, and for board system differences see Hoson vs Senyang vs BYHX carriage boards.

Why firing circuits are head-specific

Each Epson head family has its own electrical interface: the number and arrangement of connector contacts, the logic signals that select nozzles, the voltage and current required, the number of nozzle rows and the timing. The waveform that produces good drops also differs between heads because of differences in chamber design and piezo characteristics. A firing circuit is therefore designed around a particular head’s requirements. Connecting the wrong head, even if a cable could be made to fit, would at best not work and at worst damage the head or board.

The fire board compatibility factors

FactorWhat must matchRisk if mismatched
Head familyi3200, XP600, DX5, DX7, TX800 and so onNo operation; possible damage
Head variantFor i3200: eco-solvent, water-based or UV variantsWrong waveform or settings; poor printing; head and ink incompatibility
Head countBoard channels for the number of installed headsMissing heads; need for kit change
Board brand and kitSame brand and compatible generation as the mainboardNo communication with mainboard
Board versionVersion supported by your firmware and mainboardErrors, missing features, firmware refusal
Firmware and waveform filesCorrect files for head type, variant and inkPoor drop formation, misting, weak firing
Connectors and adaptersSame head cable type, adapter boards and layoutNeed for new cables; risk of wrong insertion
Power requirementsSupply voltages matching your power supplyBoard not powered correctly; damage
AuthorisationManufacturer activation if the machine is lockedBoard does not work until activated
Mechanical fitSize, mounting holes, carriage spaceBoard will not fit or cables are stressed

i3200 heads: what to watch

The Epson i3200 is now the most popular head for new eco-solvent printers in India because of its nozzle count, speed and durability. Key compatibility points:

  • Variants: i3200 heads come in variants for different ink types, commonly identified as E1 for eco-solvent, A1 for water-based and DTF, and U1 for UV. They look very similar. For an eco-solvent machine, use the eco-solvent variant, and ensure the board, firmware and settings are configured for it.
  • Adapter boards: many i3200 systems use adapter or transfer boards between the board and head. These must be the correct type for your board system and head.
  • Board generations: board makers have released several generations of i3200 boards. A newer carriage board may need newer mainboard firmware, and an older mainboard may not support it.
  • Head count options: single, double and four-head i3200 boards exist in several systems. The board must match the installed head count and the mainboard’s support.

Our comparison of i3200 and XP600 heads covers the head-level differences.

XP600 heads: what to watch

The XP600 remains common in entry-level eco-solvent and DTF printers. Key points:

  • Many board versions: because XP600 has been used for years, many board generations exist. Older machines may have boards that are no longer produced.
  • Ink use: XP600 heads are used with eco-solvent, water-based and DTF inks. The board’s waveform and settings should match the ink type used.
  • Single and double configurations: single-head XP600 machines are very common; double-head configurations need matching boards and often matching mainboards.
  • Price sensitivity: XP600 boards are relatively affordable, which has led to many copies and unbranded boards in the market. Quality varies.

DX5 and DX7 heads: what to watch

DX5 and DX7 heads were the standard for many eco-solvent machines for years and are still found in older printers. Key points:

  • Ageing board systems: many DX5 machines run older board generations. Exact replacements may only be available as old stock, refurbished or repaired.
  • Head availability: genuine DX5 heads have become harder to find and more expensive, which affects the decision to repair the board or upgrade the whole system.
  • Different interfaces: DX5 and DX7 have different interfaces and are not interchangeable without the correct board support.

When a DX5 machine needs a fire board or carriage board, compare the cost and availability with a complete kit upgrade to XP600 or i3200. Our article on keeping an older DX-based printer running discusses this decision.

Head comparison summary

HeadBoard availabilityMain compatibility concerns
i3200Good; several generationsVariant, adapter boards, board generation, head count
XP600Very good; many versions and copiesVersion matching, quality of copies, ink-specific settings
DX5 / DX7Limited; older systemsObsolete versions, cost versus upgrade

Waveform and firmware compatibility

A physically correct board is not enough if it runs the wrong firmware or waveform. Board makers provide waveform files tuned for head type, variant and ink. Using a waveform meant for a different variant or ink can lead to misting, weak drops, satellites or air ingestion. When you receive a replacement board:

  • Confirm the firmware version with the supplier against your mainboard and software.
  • Confirm the waveform or print mode files are for your head variant and ink type.
  • Do not load files from unknown sources.
  • Keep copies of the working files from your machine as a backup.

If print quality changes after a board replacement despite correct voltage and calibration, waveform files are a likely cause.

Mixing boards: what does not work

  • Fire board or carriage board from one brand with a mainboard from another brand.
  • A board for one head family with a different head family.
  • A newer board generation with an older mainboard that does not support it, without a firmware update.
  • A single-head board where two heads are installed.
  • Generic cables or adapters that look similar but have different contact layouts.

Attempts to make incompatible combinations work with improvised cables or adapters risk damaging both the board and the heads.

Authorisation and locked systems

Some machine manufacturers lock their board configurations, so that a board bought elsewhere does not work until activated. Others restrict access to head settings or waveforms. Before buying a replacement from the open market, ask your machine supplier whether the board needs activation and whether they will support it. Also ask whether using a third-party board affects your warranty. See our warranty and AMC guide for questions to ask.

Changing head type: board implications

If you plan to change head type, for example from XP600 to i3200 or from DX5 to i3200, the fire board or carriage board must change too. In practice, the mainboard, data cable, head cables, adapter boards, firmware and software usually change as well, along with the head plate, dampers and capping station. This is a complete kit change, not a fire board swap. Our articles on single to double head upgrades and XP600 vs i3200 for vinyl machines cover the wider decision.

How to confirm compatibility before buying

  1. Photograph the existing board, both sides, with all labels and stickers visible.
  2. Photograph the mainboard label.
  3. Record head type, variant and serial numbers, and the number of heads.
  4. Take screenshots of firmware and software versions.
  5. Note the ink brand and type used.
  6. Send all of this to the supplier and ask for written confirmation of the exact board model and version they will supply.
  7. Ask whether firmware, waveform files and activation are included.
  8. Ask about warranty and what it excludes.

Our guide on identifying spares by model and part number explains how to document your machine.

Testing a replacement board safely

When a replacement board arrives, a careful first start-up reduces the risk to your heads if something is not compatible:

  1. Compare the new board with the old one: connectors, layout, labels and version stickers. Stop if anything differs unexpectedly.
  2. Install it with power off, using new head cables where possible.
  3. Where your supplier recommends it, power on first with heads disconnected to confirm the board initialises and communicates.
  4. Check the firmware version and head type settings, and enter voltage values before printing.
  5. Connect the heads with power off, then power on and check head detection.
  6. Print a nozzle check and watch for misting, weak firing or unusual heat.

Our carriage board replacement checklist gives the full step-by-step procedure.

Signs that a board is not compatible after installation

  • Board not detected by the mainboard or software.
  • Heads not detected or detected as the wrong type.
  • Firmware update fails or refuses to install.
  • Print quality poor despite correct voltage and calibration.
  • Misting, satellites or weak firing that did not exist before.
  • Board or heads running unusually hot.

If any of these appear, stop and contact the supplier. Continuing to run a mismatched board can damage heads.

Feature compatibility: more than “does it fire”

Two boards that both drive your head can still differ in features that matter to your production. Before accepting a substitute or newer board, confirm that it supports:

  • Variable drop or grayscale printing: if your current setup uses variable drop sizes for smoother gradients, the replacement must support the same capability with your head.
  • Your print modes and resolutions: the modes you use daily, with matching waveforms.
  • Head temperature compensation: if your current board uses it, losing it can make print density vary with shop temperature.
  • Your RIP and print control software versions: some newer boards need newer software, which may change your workflow or require new licences.
  • Network or USB connection: the same PC connection type, or you may need different cables and settings.
  • White ink or special channels: rarely relevant for standard eco-solvent work, but important if your machine uses them.

Losing a feature you relied on can be as disruptive as a board that does not work at all, so list the features you use before ordering.

Build a compatibility record for your machine

The fastest way to order the right board in an emergency is to have a compatibility record prepared in advance. Create a single page that contains:

ItemExample of what to record
Printer make, model, width, serialAs shown on the machine plate
Board system brandHoson, Senyang, BYHX or other
Mainboard model and versionFrom the board label
Carriage or fire board model and versionFrom the board label
Adapter boardsType and quantity
Head type, variant and countFor example two i3200 eco-solvent heads
Head cables and data cableType, length, contact count
Firmware and software versionsFrom the software about screen
Ink brand and typeAs used
Supplier contacts and activation detailsWho to call, any licence codes

Keep printed and digital copies, with photos of each board. When something fails, you can send the page to suppliers immediately and get accurate quotes the same day.

Questions Indian buyers should ask about imported boards

  • Is this board stocked in India, or will it be imported after I order? How long will that take?
  • If it is the wrong version, can it be returned or exchanged, and who pays freight?
  • Does the price include GST, and will I receive a GST invoice?
  • Will you provide firmware and waveform files, and help install them?
  • Do you have technicians familiar with this board system in my region?
  • What is the warranty, and is it handled locally or does the board go back to the manufacturer?

Clear answers reduce the risk of long downtime caused by a wrong or faulty board stuck in transit. Our supplier comparison guide lists further checks.

Genuine, refurbished and copy boards

For popular heads, especially XP600, you will find genuine boards, refurbished boards and copies. Copies may work, but version mismatches, poorer components and missing protection are more common. Because the fire board directly drives expensive heads, the risk of using an uncertain board should be weighed carefully. For your main production machine, a genuine or properly tested board from a reliable supplier is usually the safer choice. Our guide to genuine vs compatible parts covers the checks.

Further reading: Each head family needs its own drive waveform, which is the core reason fire boards are not interchangeable.

Key takeaways

  • Fire boards are designed for a specific head family; i3200, XP600 and DX5 boards are not interchangeable.
  • Head variant, head count, board brand, version, firmware, waveform files, connectors, power and authorisation must all match.
  • i3200 needs attention to variant and adapter boards; XP600 to version matching and copy quality; DX5 to obsolescence and upgrade options.
  • Changing head type means a complete kit change, not just a fire board.
  • Confirm compatibility in writing using photos and version information before buying.

If you need a fire board or carriage board for an i3200, XP600 or DX5 machine, the Unified Engineering Dynamics team can confirm the exact match from your photos and supply the correct board with the right firmware.

More in the fire board series

Related: our head carriage board series starts with Eco-Solvent Head Carriage Board Explained, and covers head cable vs carriage board fault finding and the carriage board replacement checklist.

Related: our main board series covers main board functions and failure points, main board failure symptoms, the main board replacement checklist and how lightning, surges and earthing faults damage main boards.

For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.

Frequently Asked Questions

Can an i3200 fire board drive an XP600 head?

No. Each head family has a different electrical interface and waveform requirements. A board must be designed for the specific head family.

Is there a difference between i3200 boards for eco-solvent and DTF?

The i3200 head variants differ by ink type, and board settings or waveform files may differ too. For an eco-solvent machine, use the eco-solvent head variant with a board configured for it.

Can I use an XP600 board from another brand on my machine?

Only if it matches your mainboard brand and version. Boards from different brands usually cannot communicate with each other.

My DX5 board is obsolete. What are my options?

You can look for old stock, refurbished or repaired boards, or upgrade to a complete XP600 or i3200 kit. Compare costs, availability and the condition of the machine.

Why is print quality poor after fitting a new compatible board?

Check voltage settings and calibration first. If those are correct, the firmware or waveform files may not match your head variant or ink.

Do I need new firmware when installing a replacement fire board?

Sometimes. Ask the supplier to confirm the correct firmware for your mainboard, board version and head variant before installation.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *