Direct answer: Replacing a carriage board on an eco-solvent printer is not just a swap of one board for another. A safe replacement has five stages: confirm the old board is really faulty and the cause has been fixed; confirm the new board exactly matches the brand, version, head type and head count; back up all settings and calibration values; install with the power off, using new or verified cables and correct cable orientation; then load the correct firmware, enter the correct head voltage values from each head’s label, and recalibrate head alignment, bidirectional alignment and media feed before returning to production. Skipping any of these steps is how new boards and heads get damaged or why print quality drops after a “successful” repair.
Following a structured carriage board replacement checklist protects both the new board and your printheads.

Table of Contents
This checklist is written for shop owners who want to understand and supervise the work, and for technicians who want a structured routine. Board systems differ between Hoson, Senyang, BYHX and others, and between versions of the same brand, so always follow the specific instructions for your system. Electrical work and firmware changes should be carried out by trained personnel. For background on what the board does, see our explainer on the head carriage board.
Stage 1: Before ordering a carriage board replacement
Confirm the diagnosis
Many boards are replaced unnecessarily because the real fault was a head cable, data cable, power supply, setting or ink supply problem. Before ordering, make sure that:
- Ink supply, dampers and cleaning have been ruled out for missing colours.
- Head cables and the data cable have been inspected and, where suspected, replaced with known-good cables.
- Supply voltages to the carriage board have been checked by a technician.
- Head voltage settings and firmware have been verified.
- The board shows clear evidence of fault, such as burn marks, failed components, or a fault that persists after all other checks.
Our guide to head cable vs carriage board fault finding walks through these checks in order.
Find and fix the cause
A board rarely fails without reason. Common causes are ink leaks, wrong head voltage, damaged cables, a shorted printhead and power surges. If the cause is not fixed, the new board can fail the same way, sometimes within minutes. Before installation, confirm:
- No ink leaks from dampers, tubes or the head area. See our article on how ink leaks damage carriage boards.
- The printheads have been checked for internal shorts if the old board burned.
- Power supply output is stable and correct.
- Stabiliser or UPS and earthing are working. Our guide to stabiliser, UPS and earthing explains what each does.
Identify the exact replacement
Photograph the old board on both sides, including all labels and stickers. Record the board brand, model, version, head type, head count, connector layout and any adapter boards. Note the firmware and software versions shown in the print control software. Send this to your supplier and get written confirmation that the replacement matches. Our article on Hoson, Senyang and BYHX board compatibility explains the factors that must match.
Ask about authorisation
Some machine manufacturers lock board configurations or require activation of replacement boards. Ask the supplier and the machine manufacturer whether activation is needed and who will provide it. Arrange this before the machine is opened, so you are not left with a non-working machine waiting for a code.
Stage 2: Preparing for installation
Back up everything
Before removing the old board, if the machine can still communicate, record or export:
- Head voltage values for each head as currently set.
- Head alignment values: vertical, horizontal, head-to-head and bidirectional.
- Media feed calibration (step) values for your main media.
- Print mode settings, heater temperatures and cleaning settings.
- Any parameter files the software allows you to save.
- RIP settings and the printer configuration used in the RIP.
Even if the new board requires recalibration, the old values are a useful reference and save time. If the machine cannot communicate, use any records from installation or earlier service visits. Keeping these records after every calibration is good practice.
Gather the right parts and tools
| Item | Purpose |
|---|---|
| New carriage board (confirmed match) | Replacement |
| New head cables of correct type | Avoid carrying forward damage from old cables |
| Adapter boards if used by your system | Often damaged along with the board |
| Spare data cable | Rule out data cable faults during testing |
| Correct firmware and software files from the supplier | Ensure version match |
| Antistatic wrist strap or grounding method | Protect the board from static discharge |
| Correct screwdrivers and lint-free cloths | Clean, careful installation |
| Calibration media and test files | Alignment and feed calibration |
| Camera or phone | Photograph connections before removal |
Prepare the work area
Move the carriage to the service position before switching off. Then switch off the printer, unplug it from the mains and wait a few minutes for stored energy to discharge. Make sure the carriage area is clean and dry. Cover the head area and dampers with a cloth to prevent drips while you work above them. Keep ink, cleaning fluids and drinks away from the work area.
Stage 3: Removing the old board
- Photograph every connector on the old board, showing which cable goes where and in which orientation.
- Label cables if there is any chance of confusion.
- Release connector locks gently and remove cables straight out without pulling on the cable body.
- Remove mounting screws and lift the board out carefully, avoiding contact with other parts.
- Inspect the old board for burn marks, ink residue and damaged connectors. Photograph any damage; it helps identify the cause and supports warranty claims.
- Inspect the head connectors and cable contacts for burns or ink. If you find damage, the head may need checking and the cables replacing.
- Clean the mounting area if dust or ink residue is present.
Stage 4: Installing the new board
- Use an antistatic wrist strap or touch a grounded metal part of the machine before handling the new board. Hold the board by its edges.
- Check the new board visually for transport damage, loose parts or bent connector pins.
- Compare it with the old board: same connectors, same layout, same labels. If anything is different, stop and confirm with the supplier.
- Mount the board with all screws, making sure it does not touch the carriage metal anywhere it should not.
- Connect the data cable and power cable, checking orientation and full insertion.
- Fit new head cables. Insert each straight and fully into the connector, in the correct orientation, and close the lock. Check again with a torch.
- Route cables with gentle curves, away from dampers and wet areas, and make sure they do not pull or rub when the carriage moves.
- Fit any adapter boards correctly.
- Remove the protective cloth from the head area and check that no tools, screws or debris are left in the carriage.
- Have a second person check the connections against the photos before power on, if possible.
Stage 5: First power-on and firmware
Power on carefully
Before connecting the heads, some technicians power on the new board alone to confirm that it initialises and communicates, then switch off and connect the heads. Whether this is appropriate depends on the system; follow your supplier’s advice. At first power-on, watch for indicator lights behaving normally, and be ready to switch off immediately if you see smoke, smell burning, or hear unusual sounds.
Check and load firmware
New boards may arrive with firmware that is newer or older than your mainboard expects. Check the firmware version in the print control software and compare it with what the supplier recommends for your mainboard and software version. If an update is needed:
- Use only firmware files supplied for your exact board model and version.
- Make sure power is stable during the update. Use a UPS if possible. An interrupted update can leave the board unusable.
- Do not switch off or disconnect during the update.
- Restart the printer and software after the update and confirm the new version is shown.
Do not update firmware just because a newer version exists. Update only when the supplier confirms it is required or beneficial for your configuration.
Activation if required
If the board needs authorisation, complete it now with the supplier or manufacturer. Keep a record of any codes or licence information.
Stage 6: Head voltage and head settings
This is the most critical stage for the safety of the heads. Each Epson head has voltage or rank information printed on its label. The board’s software usually requires this value to be entered for each head so that the drive signal is correct for that individual head.
- Read the voltage value or rank from each head’s label. Photograph the labels for your records. If the head is already installed and the label is hard to read, use your earlier records.
- Open the head settings or head voltage section of the print control software.
- Confirm the head type is set correctly (for example i3200 eco-solvent variant, XP600 or DX5).
- Enter the voltage value for each head in the correct position. On multi-head machines, make sure head 1 and head 2 values are not swapped.
- Save the settings and restart if the software requires it.
- Confirm the values were saved by reopening the settings.
Never guess voltage values or copy them from another machine. Running a head at the wrong voltage can cause weak printing, excessive heat, shortened head life or immediate damage.
Stage 7: Priming and first tests
- Check ink supply, dampers and tubes for leaks before printing.
- Run a normal cleaning to prime the heads.
- Print a nozzle check. Compare it with the nozzle check before the failure.
- If nozzles are missing, run cleanings as normal, but if entire heads or sharply defined blocks are missing, switch off and recheck cables and settings before continuing.
- Print a few small test files and check for random dots, lines or unusual patterns.
- Run the machine for a while and check whether the board area becomes unusually hot, using the back of your hand near (not on) the board with appropriate caution, or ask the technician to check.
Stage 8: Calibration
A new board can change timing slightly, and any work in the carriage can disturb head position. Calibrate fully before returning to production. The usual sequence is:
| Calibration | What it corrects | Symptom if skipped |
|---|---|---|
| Head height check | Distance between head and media | Blurred print, head strikes |
| Head angle (vertical alignment) | Head squareness to media travel | Jagged vertical lines, banding |
| Head-to-head alignment (multi-head) | Position of second head relative to first | Visible joins, colour fringing, banding |
| Colour-to-colour alignment | Alignment between nozzle rows | Colour fringes on fine text |
| Bidirectional alignment | Left-to-right vs right-to-left pass timing | Double lines, blurred text in bidirectional mode |
| Media feed (step) calibration | Feed distance per pass | Light or dark horizontal banding |
Calibrate each print mode and resolution you use regularly, and media feed for your main media types. Save the final values and record them in your machine log. If banding remains after calibration, use our guide to narrowing down the cause of banding.
Stage 9: Colour check and production test
For a like-for-like board replacement, your existing ICC profiles usually remain valid, but the voltage settings and calibration affect ink output. Print a colour reference file and compare it with an earlier print on the same media. If colours have shifted noticeably, check voltage settings first, then consider re-profiling. Finally, run a real production job in your most common mode and check quality, speed and drying.
Stage 10: Handover and records
A professional board replacement ends with clear records. The technician should provide, and you should keep:
- The replaced board’s brand, model, version and serial or batch number.
- Firmware and software versions after installation.
- Head voltage values entered for each head.
- Calibration values for each mode.
- Parts replaced, including cables and adapter boards.
- The cause of the original failure and what was done to fix it.
- Warranty terms for the new board and the work.
- Photos of the old board damage and the new installation.
These records make future service faster and help with warranty claims. They are also useful if you later sell the machine. Our article on warranty and AMC contracts explains how records support claims.
Printable quick checklist
| # | Task | Done |
|---|---|---|
| 1 | Diagnosis confirmed; cables, power, settings and ink ruled out | ☐ |
| 2 | Cause of failure found and fixed (leak, short, surge, voltage) | ☐ |
| 3 | Replacement confirmed in writing: brand, version, head type, head count | ☐ |
| 4 | Authorisation or activation arranged if required | ☐ |
| 5 | Settings, voltages and calibration values backed up | ☐ |
| 6 | Carriage at service position, power off, unplugged, discharged | ☐ |
| 7 | Connections photographed before removal | ☐ |
| 8 | Old board, head connectors and cables inspected for damage | ☐ |
| 9 | New board fitted with antistatic precautions | ☐ |
| 10 | New head cables fitted straight, fully seated, correct orientation | ☐ |
| 11 | Connections double-checked before power on | ☐ |
| 12 | Firmware confirmed or updated on stable power | ☐ |
| 13 | Head type and voltage values entered and saved for each head | ☐ |
| 14 | Leak check, priming, nozzle check and test prints done | ☐ |
| 15 | Head height, angle, head-to-head, bidirectional and feed calibrated | ☐ |
| 16 | Colour and production test passed | ☐ |
| 17 | Records and warranty details handed over | ☐ |
Further reading: Boards are sensitive to electrostatic discharge, which is why antistatic precautions appear throughout this checklist.
Key takeaways
- Confirm the board is really faulty and fix the root cause before installing a new one.
- Match brand, version, head type and head count exactly, and arrange any activation in advance.
- Back up settings, work with the power off, use antistatic precautions and new head cables.
- Load only the correct firmware on stable power, and enter each head’s voltage value carefully.
- Recalibrate fully, test production quality, and keep complete records.
The Unified Engineering Dynamics team can supply matched carriage boards, confirm compatibility from your photos, and guide or carry out installation, voltage setting and calibration for your eco-solvent printer.
More in the head carriage board series
- Eco-Solvent Head Carriage Board Explained
- Head Board Failure Symptoms
- Hoson vs Senyang vs BYHX Carriage Boards
- Single-Head vs Double-Head Carriage Board Upgrade
- How Ink Leaks and Solvent Vapour Damage the Carriage Board
- Head Cable vs Carriage Board: Finding the Fault
- Burnt Head Board After Printhead Change
- Carriage Board Price in India
- Carriage Board Connectors: Handling Rules
Related: our fire board series explains the firing circuit that drives the heads, starting with What Is a Fire Board?, plus fire board failure signs and head voltage settings.
Related: our main board series covers main board functions and failure points, main board failure symptoms, the main board replacement checklist and how lightning, surges and earthing faults damage main boards.
For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.
Frequently Asked Questions
Do I need to update firmware when replacing a carriage board?
Only if the supplier confirms that the new board’s firmware does not match your mainboard and software version. Use only firmware supplied for your exact board model, and update on stable power.
Where do I find the head voltage value?
It is printed on the label of each Epson printhead as a voltage value or rank. Photograph it during installation and keep it in your records, because the label can be hard to read once the head is installed.
Can I use the old head cables with the new board?
It is safer to use new head cables, especially if the old board or a head burned. Damaged cable contacts can carry the fault into the new board.
Do I need to recalibrate after a board change?
Yes. Head alignment, bidirectional alignment and media feed should be checked and recalibrated after a board replacement, because timing and head position can change.
Will my colour profiles still work after a board replacement?
For a like-for-like replacement with correct voltage settings and calibration, existing profiles usually remain usable. Check a colour reference print and re-profile if colours have shifted.
How long does a carriage board replacement take?
A straightforward like-for-like replacement with calibration typically takes a few hours. Diagnosis, waiting for parts, activation or extra repairs can extend downtime, so plan and order in advance.