Direct answer: An eco-solvent printer’s electronics work as a chain. The mainboard is the fixed “brain” in the electronics box: it talks to the PC, runs the motors, heaters and sensors, and sends print data to the carriage. The head board (carriage board) rides on the carriage: it receives that data, times each firing with the encoder, and manages the heads. The fire board, which is either a separate driver board or a firing section built into the head board, generates and amplifies the voltage waveform that actually fires the nozzles. Faults in motion, heating and PC connection usually belong to the mainboard; head detection and data problems usually belong to the head board or cables; weak firing, no firing and repeated head burning usually point to the firing circuit. Knowing which board does what helps you report symptoms accurately and avoid buying the wrong part.
Knowing the difference between fire board vs head board vs mainboard makes service reports and spare part quotes much easier to understand.

Table of Contents
This guide maps the chain from computer to nozzle, explains each board’s job, lists the faults typical of each, and shows how to work out which board is most likely involved. It is part of our fire board series; for the basics of the firing circuit, start with what is a fire board.
The electronics chain from computer to nozzle
Every print passes through the same sequence of steps. A fault anywhere in the sequence stops or degrades printing, and the symptom often appears far from the cause. The chain looks like this:
- PC and RIP software: processes the image, applies colour profiles and creates the print file.
- Print control software: sends the job and printer settings to the machine, and shows status and errors.
- PC-to-printer link: USB or network cable.
- Mainboard: receives data, controls motion and heaters, and forwards print data.
- Data cable: carries print data from mainboard to carriage through the cable chain.
- Head board (carriage board): buffers data, synchronises firing with encoder position and manages head communication.
- Fire board or firing section: generates and amplifies the drive waveform for each head.
- Head cables and adapter boards: deliver signals and waveform to the heads.
- Printheads: select nozzles and fire drops.
Alongside this data chain runs the power chain: mains power through stabiliser or UPS to the printer’s power supply, which feeds DC voltages to the mainboard, carriage electronics and motors. A weak or unstable power supply affects every board.
The mainboard: the fixed controller
The mainboard sits in the electronics compartment, usually on the side or rear of the printer, and does not move. Its main jobs are:
- Communicating with the PC and print control software.
- Controlling the carriage motor and media feed motor through motor drivers.
- Reading sensors: origin, media, paper end, cover, limit switches and others.
- Controlling heaters, dryers and fans, often through relays or separate heater boards.
- Managing the cleaning station, pump and capping motions.
- Sending print data to the carriage at the correct time.
- Storing machine parameters and calibration values.
Typical mainboard fault symptoms
- PC cannot connect to the printer, or connection drops frequently.
- Machine does not initialise, carriage does not move to home, or media does not feed.
- Heater errors, heaters not heating, or heaters stuck on.
- Cleaning station or pump not working.
- Sensor errors that persist after checking the sensors.
- Parameters lost after switching off.
The head board: the carriage controller
The head board, also called the carriage board, is mounted on the moving carriage. Its main jobs are:
- Receiving and buffering print data from the mainboard.
- Reading the encoder and timing each firing to the carriage position.
- Communicating with heads, reading head identity and status.
- Distributing logic power to head electronics.
- Reading carriage-side sensors on some systems.
- On many systems, hosting the firing circuit as well.
Typical head board fault symptoms
- Head not detected or head communication errors.
- Random dots, garbage prints or repeated blocks.
- Faults that come and go with carriage position (often cable-related).
- Whole heads or sharply defined channels missing.
Our article on the head carriage board covers this board in depth.
The fire board: the power stage for the heads
The fire board, or firing section, takes the timing and data from the head board and produces the actual drive waveform at the correct voltage for each head. Its main jobs are:
- Generating the waveform shape defined by firmware and print mode.
- Amplifying it to the drive voltage needed by the head.
- Adjusting amplitude per head according to the voltage value entered in software.
- Supplying enough current for all nozzles firing at high frequency.
- On some systems, compensating for head temperature.
Typical fire board fault symptoms
- Heads detected but no ink fired, although cleaning draws ink normally.
- A whole head prints uniformly weak or pale.
- Nozzle loss that appears after warm-up and recovers after cooling.
- New heads failing quickly on the same channel.
- Burn marks or hot spots around power transistors.
Integrated vs separate fire boards
On many current eco-solvent machines with XP600 or i3200 heads, the firing circuit is part of the head board. In that case, a “fire board fault” means the firing section of the head board has failed, and the whole head board is usually repaired or replaced. On machines with a separate fire board, it may be possible to replace just that board.
| Design | Advantages | Disadvantages |
|---|---|---|
| Firing integrated into head board | Fewer connectors, compact, common on modern kits | Firing fault means replacing or repairing the whole head board |
| Separate fire board | Firing section can be replaced alone; heat can be managed separately | More boards and connectors, more possible failure points |
Check which design your machine uses before ordering parts. A photo of the carriage electronics usually makes this clear to a supplier.
Fire board vs head board vs mainboard: comparison table
| Function | Mainboard | Head board | Fire board |
|---|---|---|---|
| PC communication | Yes | No | No |
| Motor control | Yes | No | No |
| Heater control | Yes | No | No |
| Print data buffering on carriage | No | Yes | No |
| Encoder timing | Partly | Yes | Uses timing from head board |
| Head identification | No | Yes | No |
| Waveform generation and amplification | No | Yes, if integrated | Yes |
| Per-head voltage adjustment | Stores settings | Yes, if integrated | Yes |
| Location | Fixed electronics box | Carriage | Carriage |
Symptom-to-board guide
No symptom identifies a board with certainty, but this table helps narrow down where to look first.
| Symptom | Most likely area | Also check |
|---|---|---|
| PC cannot connect | PC settings, cable, mainboard | Network settings, power |
| Carriage or media motor not moving | Mainboard motor driver, motor | Mechanical jam, belts, sensors |
| Heater not working or error | Mainboard heater control, heater, sensor | Fuses, relays, heater board |
| All heads not detected | Head board, data cable, power | Mainboard communication |
| One head not detected | Head cable, adapter, head board channel | Head itself |
| Random patterns in print | Data cable, head board, earthing | Power supply, mainboard |
| Heads detected, no firing | Fire board or firing section, voltage settings | Power supply rails |
| Whole head weak | Voltage setting, firing section | Clogging, ink supply, head age |
| New heads fail on same channel | Firing section on that channel, cables | Settings, ink in connectors |
| Faults after warm-up | Firing section heat, head board components | Carriage fans, ventilation |
The power supply: the part everyone forgets
The three boards depend on the printer’s power supply unit (PSU), which converts mains electricity into the DC voltages the electronics need. Many eco-solvent printers have one main PSU, and some have separate supplies for heaters or motors. When a PSU starts to fail, its output may sag under load, carry electrical noise, or drop out briefly. The symptoms can look like any board fault: random errors, heads disappearing, weak firing, motors stalling, or the machine restarting.
The firing section is often the first to show PSU problems, because it draws the most power on the carriage when many nozzles fire together. A print that fails only on heavy solid areas, but prints text and light images normally, can be a sign that the supply sags under load. Before replacing a head board or fire board, have a technician confirm that the PSU delivers stable voltages under printing load, not just at idle. PSUs are cheaper than boards and heads, and a weak one can damage new boards.
Other boards you may find in the chain
Besides the three main boards, many printers include smaller boards that are easy to confuse with them:
| Board | Typical role | Often confused with |
|---|---|---|
| Adapter or transfer board | Converts connectors and routes signals to a specific head, common on i3200 | Fire board or head board |
| Heater control board | Switches and regulates pre-heater, platen heater and dryer | Mainboard |
| Motor driver board or modules | Drives carriage and feed motors (servo or stepper) | Mainboard |
| Encoder reader board | Reads the encoder strip on the carriage | Head board |
| Sensor boards | Media, origin and cover sensors | Head board or mainboard |
| Control panel board | Buttons and display on the front panel | Mainboard |
A fault in any of these can produce symptoms that look like a main board problem. For example, a faulty encoder reader can cause misaligned printing that looks like a head board timing fault. Our encoder and sensors guide explains those parts.
Worked example: tracing a fault through the chain
Consider a double-head i3200 printer where head 2 suddenly prints very pale while head 1 is normal. Working through the chain:
- PC and RIP: head 1 prints correctly from the same file, so the file and RIP are fine.
- Mainboard: the machine connects, moves and heats normally, and head 1 prints, so the mainboard is very likely fine.
- Ink supply: the damper for head 2 is full and cleaning pulls ink well from both heads.
- Settings: checking the software shows head 2’s voltage value has been entered lower than the label value after a recent software reinstall. Correcting it restores normal density.
In this example no board was faulty at all. Had the setting been correct, the next steps would have been the head 2 cable, then the firing channel for head 2, then the head itself. Working along the chain in order turns a vague “board problem” into a short list of specific checks.
How faults travel along the chain
Faults rarely stay in one place. Understanding how they travel helps prevent repeat failures:
- Head to fire board: a shorted head overloads the amplifier, damaging the firing channel.
- Fire board to head: a failed amplifier transistor sends abnormal voltage, damaging the head.
- Cable to both: a burnt or crooked head cable creates a short that damages head and firing section.
- Power supply to all: unstable or surging supply voltages stress every board, often hitting the firing section first because it handles the most power on the carriage.
- Ink to carriage electronics: leaks short connectors on the head board and firing section.
This is why a good technician checks the whole chain after an electrical failure instead of simply replacing the part that failed last. Our article on burnt head boards after a printhead change shows how these chains of damage play out.
Board kits: why the boards must match
The mainboard, head board and any separate fire board are designed as a kit by the board maker, such as Hoson, Senyang or BYHX. They share data protocols, firmware and software. Mixing boards from different brands or incompatible versions usually fails, and can cause errors or unsafe drive behaviour. When replacing any one board, confirm that it matches the others in brand, version and head configuration. See our board compatibility guide for details.
Reporting faults so the right board gets checked
Technicians diagnose faster when the report is precise. Instead of “head board problem”, describe:
- What the printer does and does not do: connects or not, moves or not, heats or not, detects heads or not.
- Exact error messages, with screenshots.
- Nozzle check photos.
- Whether the fault is constant, intermittent, position-related or heat-related.
- What happened before: head change, cleaning, leak, power cut, storm, relocation.
From this, a technician can usually tell which part of the chain to examine first. Our guide to recording and reporting nozzle checks shows what to capture.
Quick owner self-check before calling a technician
Before calling for service, an owner or operator can do a short set of safe checks that often narrows the problem to one part of the chain:
- Does the PC connect and the print control software show the printer as online? If not, look at the PC side and mainboard first.
- Does the machine initialise, move the carriage home and feed media? If not, the mainboard, motors or sensors are involved.
- Do the heaters reach their set temperatures? If not, heater control is involved.
- Are all heads shown as detected in the software? If not, the head board, data cable or head cables are involved.
- Does cleaning pull ink from every head? If not, the ink system is involved.
- Does the nozzle check show weak, missing or random output? This points to settings, cables, firing section or heads.
- Did anything happen just before the fault, such as a head change, leak, power cut or storm?
Writing down the answers to these seven questions, together with screenshots and nozzle check photos, gives your technician a clear starting point and often avoids a wasted visit.
Ordering the right board
Many wrong orders happen because the buyer and seller use different names. To avoid this:
- Photograph the board you believe is faulty, both sides, with labels.
- Photograph the other boards in the kit too, so the seller can confirm compatibility.
- State head type, variant and count.
- State firmware and software versions.
- Describe the fault and the checks done.
- Ask the seller to confirm in writing which board they are supplying and that it matches.
Further reading: The printer mainboard plays a role similar to a computer motherboard, coordinating the other boards.
Key takeaways
- The mainboard controls the machine and PC link, the head board manages the carriage and heads, and the fire board generates the firing waveform.
- On many eco-solvent machines, the firing circuit is integrated into the head board.
- Motion, heater and connection faults point to the mainboard; head detection and data faults to the head board and cables; weak or no firing to the firing section.
- Faults travel along the chain, so check the whole chain after an electrical failure.
- Boards must match as a kit; describe symptoms precisely and order with photos to avoid mistakes.
If you are unsure which board in your printer is causing a problem, the Unified Engineering Dynamics team can help interpret symptoms, identify the board and supply the correct part.
More in the fire board series
- What Is a Fire Board on an Eco-Solvent Printer?
- Fire Board Failure Signs
- Why a Bad Fire Board Can Kill a New Printhead
- Head Voltage Settings and Head Life
- Fire Board Compatibility for i3200, XP600 and DX5
- Fire Board Repair vs Replacement
- Power Fluctuation and Fire Board Damage
- Fire Board Cooling and Dust
Related: our head carriage board series starts with Eco-Solvent Head Carriage Board Explained, and covers head cable vs carriage board fault finding and the carriage board replacement checklist.
Related: our main board series covers main board functions and failure points, main board failure symptoms, the main board replacement checklist and how lightning, surges and earthing faults damage main boards.
For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.
Frequently Asked Questions
What is the difference between the mainboard and the head board?
The mainboard is fixed in the electronics box and controls PC communication, motors, heaters and sensors. The head board rides on the carriage, receives print data and manages the printheads.
Is the fire board part of the head board?
On many eco-solvent printers, yes. The firing circuit is integrated into the head board. Some machines use a separate fire board.
My printer cannot connect to the PC. Is it the head board?
Usually not. PC connection problems are more often caused by PC settings, cables or the mainboard. The head board handles carriage-side functions.
Heads are detected but nothing prints. Which board is faulty?
If ink supply and cleaning are confirmed good, the firing section or voltage settings are prime suspects. Power supply rails should also be checked.
Can I replace just the fire board?
Only if your machine uses a separate fire board. If the firing circuit is built into the head board, the head board must be repaired or replaced.
Can I mix boards from different brands?
No. Mainboard, head board and fire board are designed as a matched kit. Mixing brands or incompatible versions usually does not work.