Eco Solvent Printing, Printheads

Burnt Head Board After Printhead Change: Common Causes and How to Avoid It

Burnt Head Board After Printhead Change: 9 Causes

Direct answer: When a head board burns immediately or soon after a printhead change, the cause is almost always something that happened during the change, not bad luck. The most common causes are plugging or unplugging head cables with the power on, inserting a head cable at an angle or the wrong way round, reusing a head cable with burnt contacts from the old head, ink or cleaning fluid in the connector, entering the wrong head voltage or head type, fitting a head that is itself shorted or damaged, and a board channel that was already weakened by the failure that killed the old head. Avoiding the problem comes down to a disciplined installation routine: power off, inspect, use new cables, insert carefully, check the head, set the correct voltage, and investigate why the old head failed before fitting the new one.

A burnt head board after a printhead change is usually caused by one of a few avoidable mistakes, covered below.

Burnt Head Board After Printhead Change: 9 Causes
Burnt Head Board After Printhead Change: 9 Causes

Losing a new head and a head board together is one of the most expensive failures an eco-solvent shop can face. It often happens to experienced operators in a hurry, and it is often blamed on the head supplier or board quality. This guide explains what really happens, how to tell what went wrong, and how to make sure it does not happen again. It applies to i3200, XP600, DX5, DX7 and similar heads on common board systems.

Why a burnt head board often follows a printhead change

During normal printing, the head, cable and board are connected and stable. A head change disturbs everything at once: cables are unplugged and replugged, connectors are exposed to ink and cleaning fluid, settings must be changed, and a new part with unknown history is introduced. If the old head failed electrically, its fault may have damaged the cable or board as well. Every one of these steps is a chance for something to go wrong. Knowing the risks helps you control them.

Cause 1: Hot-plugging cables

Plugging or unplugging a head cable while the printer is powered is one of the most common causes of burnt boards. When a connector is inserted, its contacts do not all touch at the same instant. For a brief moment, drive voltage can reach the wrong contact, or a signal line can be connected before the ground line. This can damage driver components on the board and electronics inside the head.

Hot-plugging often happens unintentionally: the operator switches the printer on to move the carriage to the service position, forgets to switch off, and then starts unplugging cables. The fix is a strict rule: move the carriage first, then switch off at the main switch, unplug from the mains, and wait before touching any cable.

Cause 2: Cable inserted at an angle or reversed

Head connectors use flat flexible cables with very fine, closely spaced contacts. If a cable is inserted slightly crooked, contacts can bridge between neighbouring pins. If a cable that can physically go in either way is inserted reversed, every signal goes to the wrong pin. Either mistake can burn the board, the head, or both, the moment the printer is powered.

Prevention: photograph the connection before removal, insert cables straight and fully, check with a torch that the cable is level and evenly seated across its width, close the lock without forcing, and have someone double-check before switching on.

Cause 3: Reusing a damaged head cable

When a head fails electrically, the short circuit often burns the contacts of the head cable as well. Those burnt contacts can have carbon tracks or melted plastic that create a new short. If that cable is reused with the new head, it can damage the new head and the board channel. This is a classic reason for “the new head died within minutes”.

Prevention: inspect head cables closely whenever a head is changed. Replace any cable with discoloured, blackened, dull or melted contacts, creases or ink stains. Many technicians replace head cables with every head change as a matter of routine, because the cost is small compared with the risk. Our guide to head cable vs carriage board fault finding explains what to look for.

Cause 4: Ink or cleaning fluid in the connector

During a head change, the old head is removed with ink still in it, and the area is often cleaned with fluid. Drops can land on the head connector, the cable or the board. If the printer is powered while liquid bridges contacts, a short occurs. Ink can also wick along a cable into the connector after the job seems finished.

Prevention: cover the board and connectors before removing the old head; cap or wrap the old head immediately; wipe the work area dry; inspect connectors and cable ends with a torch before power on; and allow time for any cleaning fluid to evaporate. See our article on how ink leaks damage carriage boards for more detail.

Cause 5: Wrong head voltage or head type setting

Each Epson head has its own voltage value or rank on its label. The board software uses this value to set the drive signal. If the new head’s value is not entered, if values for two heads are swapped, or if the head type is set incorrectly, the head may be overdriven. Overdriving makes the head and the drive circuit run hotter and can lead to failure, sometimes not immediately but after hours or days of printing.

Prevention: read and photograph the voltage value from the new head’s label before installing it, enter it carefully in the correct head position, confirm the head type, save, and recheck. Never copy values from the old head or another machine. Our carriage board replacement checklist includes the voltage entry steps in detail.

Cause 6: A faulty or damaged new head

Not every new head is perfect. A head can be damaged in transport, stored badly, or be a refurbished or non-genuine unit with hidden faults. Heads with internal electrical faults can draw excessive current and damage the board channel the first time they are powered. Heads sold as new may also be the wrong variant, such as a water-based variant for an eco-solvent machine.

Prevention: buy heads from reliable suppliers, check the packaging and seals, verify the part number and variant, inspect the connector for damage, and ask the supplier how the head was tested. Our guides on genuine vs compatible printheads and new vs refurbished printheads cover the checks.

Cause 7: The board was already damaged

This is the cause most often missed. If the old head failed because of a board problem, or if the old head’s short weakened the board’s driver components, the board may already be damaged when the new head is fitted. The new head is then connected to a faulty channel and fails quickly. To the operator it looks as though the new head burned the board, when in fact the board killed both heads.

Prevention: before fitting a new head, investigate why the old head failed. If there is any sign of electrical failure, such as burnt cable contacts, a burning smell, sudden total failure of the head, or board errors, have a technician check the board channel before connecting the new head. Some technicians check the board’s drive output or test with a known-good, low-value head before risking an expensive new one.

Cause 8: Static discharge during handling

Heads and boards contain components sensitive to static electricity. Handling them without grounding, especially in dry weather or while wearing synthetic clothing, can cause damage that shows up as early failure. Prevention: touch a grounded metal part of the machine before handling, use an antistatic wrist strap if available, hold parts by their edges, and keep heads in their packaging until installation.

Cause 9: Power problems at switch-on

Voltage fluctuations, poor earthing or a failing power supply can stress the board at the moment of switch-on after a head change. If power quality is poor, the extra stress of a newly connected head can be the final straw. Ensure stabiliser or UPS and earthing are working correctly. Our guide to stabiliser, UPS and earthing explains the requirements.

Special notes for i3200 and multi-head machines

Machines with i3200 heads and machines with two or more heads have a few extra risk points during a head change:

  • Adapter boards: many i3200 systems use a small adapter or transfer board between the head cable and the head. These boards sit very close to the dampers and are often contaminated with ink. Inspect them as carefully as the cables, and replace them if there is any sign of burning or residue.
  • Two cables per head: some heads connect with more than one cable. Mixing up the two cables, or leaving one partly seated, can cause shorts or missing nozzle rows. Label each cable before removal.
  • Head position confusion: on a double-head machine, the voltage for head 1 must go into the head 1 position in the software. Swapping values means one head is overdriven and the other underdriven. Mark heads physically and in your records.
  • Changing one head of a pair: fitting a new head next to an old one is common, but if the old head is near the end of its life, it may fail soon and tempt a second rushed head change. Plan replacements so that both heads are reviewed together.
  • Head variant: confirm that the new i3200 is the eco-solvent variant intended for your ink. A head meant for water-based or UV ink can fail quickly in an eco-solvent system, and the failure can look like an electrical problem.

Our comparison of i3200 and XP600 printheads explains more about head variants and their differences.

Summary of causes and prevention

CauseHow it damagesPrevention
Hot-pluggingMomentary wrong connections send voltage to wrong pinsMove carriage, switch off, unplug, wait
Crooked or reversed cableShorts between adjacent pins or wrong signal routingPhotograph, insert straight, check, double-check
Reused burnt cableCarbon tracks short drive linesInspect and replace head cables
Ink in connectorLiquid bridges contactsCover board, dry area, inspect before power on
Wrong voltage or head typeOverdriving heats head and drive circuitEnter label value carefully, confirm head type
Faulty new headInternal short loads board channelReliable supplier, verify variant, inspect
Already damaged boardFaulty channel kills new headFind why old head failed; test board channel first
Static dischargeWeakens components, early failureGround yourself, handle by edges
Poor power qualitySurges stress board at switch-onStabiliser or UPS, verified earthing

How to tell what went wrong after a burn

If a board has already burned after a head change, the evidence can show what happened. Before discarding anything, have a technician examine:

  • Burn location on the board: burns at the head connector or the related driver components suggest a short from cable or head; burns in the power section may indicate a supply or surge issue.
  • Cable contacts: burnt marks at specific contacts can show which lines shorted, and whether the cable was crooked.
  • Head connector: damage on the head side suggests the head was involved.
  • Ink traces: dried ink on connectors or the board points to liquid as the cause.
  • Software settings: the voltage and head type entered, if the board can still communicate or if records exist.
  • Sequence of events: whether the failure happened at switch-on, during cleaning or after some hours of printing. Instant failure suggests a short or hot-plugging; failure after hours suggests overdriving or heat.

Photograph all evidence. It helps with understanding the cause and with any warranty discussion with the head or board supplier.

Recovering after a burn

When both a board and a head are damaged, resist the temptation to fit a new head on a new board immediately. Follow a careful recovery sequence:

  1. Identify the cause using the evidence above.
  2. Replace all head cables involved, and any adapter boards.
  3. Have the old head checked if there is doubt about whether it was the source of the short.
  4. Check the power supply and data cable.
  5. Install the new board following a proper checklist, and confirm it communicates before connecting the head.
  6. Verify the new head’s variant, connector and condition.
  7. Enter the correct voltage and head type, then connect and test.

Our article on printhead repair vs replacement helps decide whether a damaged head is worth attempting to recover.

A safe printhead change routine

Use this routine every time a head is changed. Print it and keep it near the machine.

  1. Find out why the old head is being replaced. If electrical failure is suspected, have the board and cables checked first.
  2. Check the new head: part number, variant, packaging, connector condition. Photograph the label and voltage value.
  3. Move the carriage to the service position, then switch off, unplug and wait.
  4. Ground yourself before touching electronics.
  5. Cover the board and connectors to protect them from ink.
  6. Photograph cable connections, then unplug cables gently.
  7. Remove the old head, cap or wrap it, and clean and dry the area.
  8. Inspect head cables and the board connector. Replace cables if there is any doubt.
  9. Install the new head mechanically and connect dampers carefully without spilling ink.
  10. Insert head cables straight, fully seated and in the correct orientation; close locks.
  11. Remove the cover, check for drips and debris, and double-check connections.
  12. Power on and enter the head voltage value and head type before printing.
  13. Prime, run a nozzle check, and calibrate head position and alignment.
  14. Record the head serial, voltage value, date and any observations in the machine log.

Warranty realities

Head and board suppliers usually exclude damage from incorrect installation, hot-plugging, ink contamination and wrong settings. When a new head fails immediately, the supplier will typically examine it for signs of these causes. Following and documenting a correct installation routine protects your position. Photos of the label, connections and settings, and a record of the steps followed, make a fair warranty discussion possible. Our article on printhead warranty and installation conditions explains typical terms.

Further reading: Unplugging cables with power on is the opposite of designed hot swapping; printer head cables are not designed for it.

Key takeaways

  • Head boards that burn after a printhead change are usually damaged by something done during the change.
  • The main culprits are hot-plugging, crooked or reversed cables, reused burnt cables, ink in connectors and wrong voltage settings.
  • A board weakened by the old head’s failure can destroy a new head; investigate why the old head failed first.
  • Replace head cables during head changes when in doubt, and keep the electronics dry.
  • Follow and document a safe installation routine every time; it protects your machine and your warranty position.

If you have lost a board and head after a head change, or want a technician to install a new head safely, the Unified Engineering Dynamics team can help diagnose the cause and guide a safe recovery.

More in the head carriage board series

Related: our fire board series explains the firing circuit that drives the heads, starting with What Is a Fire Board?, plus fire board failure signs and head voltage settings.

Related: our main board series covers main board functions and failure points, main board failure symptoms, the main board replacement checklist and how lightning, surges and earthing faults damage main boards.

For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.

Frequently Asked Questions

Why did my new printhead stop working right after installation?

Common causes are a cable inserted crookedly or reversed, a reused cable with burnt contacts, ink in the connector, hot-plugging, wrong voltage setting, a faulty head, or a board channel already damaged by the old head’s failure.

Can a new printhead burn the head board?

Yes, if the head has an internal electrical fault, or if it is connected through a damaged cable. Equally, a damaged board can burn a new head, which is why the cause of the old head’s failure must be investigated first.

Should I replace head cables every time I change a printhead?

It is good practice, especially if the old head failed electrically or the cables show any discoloration, creases or ink. New cables are inexpensive compared with the risk to the board and head.

Is it safe to switch on the printer to move the carriage during a head change?

Yes, but switch off and unplug before touching any cable. Many accidental hot-plugging incidents happen because the printer was left on after moving the carriage.

What happens if I enter the wrong head voltage?

The head may print weakly, or it may be overdriven, causing heat, shortened life and possible failure of the head or drive circuit. Always enter the value from the head’s label in the correct position.

Will the supplier replace a head that failed at installation?

It depends on their warranty terms and inspection. Damage from hot-plugging, wrong installation, ink contamination or wrong settings is usually excluded. Documenting your installation steps helps a fair assessment.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *