Direct answer: Main board faults in an eco-solvent printer usually show up as control problems rather than print quality problems. The most common signs are: the print control software cannot find or stay connected to the printer; the machine does not initialise or the carriage does not move to its home position; the media feed motor does not move or moves erratically; heaters do not heat, heat constantly or show temperature errors; the cleaning station or pump does not work; sensor errors persist even with good sensors; parameters are lost after switching off; or the machine restarts randomly. Each of these symptoms also has non-board causes, such as PC network settings, damaged cables, mechanical jams, dirty sensors, a weak power supply or wrong parameters, and those must be ruled out first before replacing the main board.
Many main board failure symptoms are shared with simpler faults, so a calm triage saves money.

Table of Contents
This guide works through each main symptom, the likely causes in order of probability, and simple checks. It is part of our main board series; for an overview of the board, see main board functions, ports and failure points.
Ground rules for safe checking
- Switch off and unplug before touching any cable inside the printer.
- Do not open the electronics compartment unless you are trained; mains voltages are present inside.
- Photograph connections before unplugging anything.
- Record error messages exactly and take screenshots.
- Note what happened before the fault: power cut, storm, cable work, software update, relocation.
Symptom 1: Printer not connecting to the PC
The print control software shows the printer as offline, cannot find it, or loses connection during printing.
Common causes, in order of likelihood
- PC network settings: the PC’s network adapter is not set to the address range the printer uses, or Windows changed settings after an update.
- Firewall or antivirus: blocking the print control software’s communication.
- Cable or port: damaged network or USB cable, loose plug, or a faulty port on the PC.
- Network equipment: a switch or router between PC and printer causing conflicts or dropping packets.
- PC sleep and power settings: network adapter or USB port being powered down by Windows.
- Software issues: corrupted installation, wrong version for the board, or missing drivers.
- Main board communication port: damaged by surge, static or hot-plugging.
- Main board not starting: power or firmware problem, so it never comes online.
Quick checks
- Check the link lights on the printer’s network port and the PC’s network port; no lights suggests cable, port or power issues.
- Try a new, short network cable connected directly between PC and printer.
- Confirm the PC network adapter settings match those recorded at installation.
- Temporarily check whether firewall or antivirus is blocking the software (with care and IT advice).
- Try another PC with the software installed, if available.
Our article on network port and USB problems explains these checks in detail. Most connection problems are fixed at the PC side.
Symptom 2: Machine does not initialise
When switched on, the printer does not complete its start-up routine: the carriage does not move to home, the panel shows an error, or nothing happens at all.
Common causes
- No power to the board: blown fuse, failed PSU, loose power connector, tripped breaker.
- Safety or cover sensor: an open cover or faulty cover sensor preventing start.
- Origin sensor fault: the carriage cannot find home because the sensor is dirty, misaligned or its cable is broken.
- Mechanical obstruction: carriage blocked by a tool, media or a locked carriage lock left after transport.
- Motor or driver fault: carriage motor or its driver has failed.
- Corrupted firmware: after an interrupted update or power cut.
- Main board failure: processor, memory or power regulation fault.
Quick checks
- Check that power indicators on the PSU and board (if visible) are lit.
- Check covers are closed and any carriage transport lock is removed.
- With power off, gently move the carriage by hand to check it moves freely.
- Look for obvious damage, burnt smell or loose connectors (trained personnel).
Symptom 3: Carriage not moving, or moving erratically
The carriage does not move, moves jerkily, stops partway, makes grinding noises, or the software reports a carriage or servo error.
Common causes
- Mechanical resistance: dirty or dry rails, worn bearings, damaged carriage wheels, belt too tight or damaged.
- Encoder problems: dirty or damaged encoder strip or motor encoder causing position errors.
- Belt slipping or broken.
- Motor cable damaged in the cable chain or at connectors.
- Motor failure.
- Motor driver failure on the main board or a separate driver module.
- Wrong parameters after reset or software reinstall.
A motor driver often fails because of mechanical overload, so fixing the mechanics comes first. If a driver is replaced without fixing a stiff carriage, the new driver may fail too. Our guide to carriage belts, rails and bearings covers the mechanical side, and our encoder guide covers position feedback.
Symptom 4: Media not feeding or feeding wrongly
The media does not advance, advances unevenly, skews, or the software shows feed motor errors.
Common causes
- Pinch rollers not lowered, worn or unevenly set.
- Media loaded incorrectly or too heavy for the take-up and feed system.
- Feed roller dirty or worn.
- Feed motor, belt or gear problems.
- Feed motor encoder issues.
- Feed motor driver failure on the main board.
- Wrong feed calibration values.
Most feed problems are mechanical or calibration-related. See our guide to pinch rollers and media feed parts.
Symptom 5: Heater problems
Heaters do not warm up, overheat, stay on constantly, or the software shows heater or temperature errors.
Common causes
- Failed heater element.
- Faulty or disconnected temperature sensor (thermistor).
- Failed relay, solid-state relay or heater board.
- Blown heater fuse.
- Wiring fault or loose connector.
- Wrong heater settings.
- Main board heater control circuit fault.
Heater circuits involve mains voltages and must be checked only by qualified personnel. A heater stuck on is a safety issue: switch off and have it checked immediately. See our guide to heaters, dryers and power supplies.
Symptom 6: Cleaning station or pump not working
The capping station does not rise, the wiper does not move, the pump does not pull ink, or cleaning cycles fail.
Common causes
- Mechanical jam in the capping station or wiper mechanism.
- Worn pump tubing or failed pump motor.
- Sensor for capping position faulty.
- Damaged cable.
- Main board output driver for the cleaning motors failed.
Heads left uncapped dry out quickly, so treat cleaning station failures urgently. Our capping station guide explains the parts involved.
Symptom 7: Persistent sensor errors
The machine reports media, cover, origin, limit or other sensor errors that do not clear.
Common causes
- Dirty optical sensor or reflector.
- Misaligned sensor flag or bracket.
- Broken wire or loose connector.
- Sensor plugs swapped after service.
- Failed sensor.
- Damaged sensor input on the main board, sometimes from surges on long cables.
Symptom 8: Lost parameters or settings
Calibration values, head settings or machine settings reset to defaults after switching off, or change unexpectedly.
Common causes
- Software reinstalled with default settings.
- Power cut during saving.
- Interrupted firmware update.
- Memory fault or backup battery issue on the board, where applicable.
- Wrong operating procedure, such as switching off before settings were saved.
Symptom 9: Random restarts or freezes
The printer restarts, freezes or drops connection unpredictably, sometimes mid-print.
Common causes
- Unstable mains power or voltage dips.
- Failing PSU with sagging output.
- Poor earthing causing interference.
- Overheating in the electronics compartment.
- Loose power connector on the board.
- PC-side problems such as sleep settings or software crashes.
- Main board component fault.
Symptoms after moving or reinstalling the printer
Many control faults appear right after a printer is moved to a new location, reinstalled after repairs, or connected to a new PC. Common reasons include:
- Carriage transport lock not removed, or media guides left in transport position.
- Connectors loosened by vibration during transport.
- New PC with different network adapter settings, firewall or missing software components.
- Different mains supply at the new location, with poor voltage or earthing.
- Machine not levelled, causing mechanical resistance and feed problems.
- Cables pinched or damaged during moving.
Before suspecting the main board after a move, check these points carefully. Our installation checklist lists what a proper reinstallation should include.
Capturing intermittent faults
Intermittent faults are the hardest to diagnose, because the printer may work perfectly when the technician arrives. Help the diagnosis by capturing evidence when the fault happens:
- Take a photo of the panel or a screenshot of the software error immediately.
- Note the time, the job being printed, the print mode and the carriage position.
- Note whether other heavy equipment was switched on at the same time.
- Note room temperature and whether the machine had been running for a long time.
- Note whether the fault cleared by itself, after a restart or after switching off for a while.
Patterns in this log often point directly to the cause. For example, faults that coincide with an air conditioner or compressor starting suggest power disturbances; faults after long runs suggest heat; faults at one carriage position suggest a cable in the cable chain.
Main board failure symptoms: a simple triage order
When a control fault appears, work through this order before calling for a main board replacement:
- Restart PC and printer properly, with a full power-off of at least a minute.
- Check mains power, stabiliser or UPS output, and breakers.
- Check PC-to-printer cable, settings and software.
- Check covers, locks, obstructions and mechanical movement.
- Check sensors for dirt and alignment.
- Have a technician check PSU output and connectors.
- Have a technician check motors, drivers, heater components and sensor wiring.
- Only then consider the main board.
Error codes: how to use them
Different board systems and machine manufacturers use different error codes and messages. There is no universal list. Use error codes this way:
- Write down the exact code and message, or take a screenshot.
- Check the machine’s manual or the software’s help for the meaning.
- Ask your supplier for the error code list for your board system.
- Note when the error appears: at start-up, during movement, during printing, during cleaning.
- Remember that an error tells you which function failed, not necessarily which part. A “carriage error” can be mechanical, encoder, motor, cable or driver related.
Symptom summary table
| Symptom | Check first | Main board likely if |
|---|---|---|
| No PC connection | Cable, PC settings, firewall, another PC | No link lights with known-good cable and PC; port damage after storm |
| Does not initialise | Power, covers, transport lock, obstructions | Power reaches board but nothing starts; firmware corrupted |
| Carriage not moving | Mechanics, belt, encoder, motor cable | Carriage moves freely by hand, motor and cable good, driver output absent |
| Media not feeding | Pinch rollers, loading, calibration | Mechanics and motor good, driver output absent |
| Heater errors | Element, sensor, relay, fuse, settings | Components test good, control signal absent or wrong |
| Cleaning station failure | Jams, pump tubing, sensors | Motors good, no drive output |
| Sensor errors | Clean, align, check wiring | Known-good sensor still not read |
| Lost parameters | Software reinstall, saving procedure | Settings lost repeatedly despite correct saving |
| Random restarts | Mains, PSU, earthing, heat, PC | All external causes ruled out |
Why multiple failed functions point to the board
If one function fails, such as the feed motor, the cause is usually that function’s parts. If several unrelated functions fail at the same time, such as connection, heaters and sensors together, a shared cause becomes more likely: the main board, its power supply, or an earthing problem. This is a useful clue, especially after a storm or power event.
Symptoms after a storm or power event
If faults appear immediately after a thunderstorm, a power cut, a voltage spike or electrical work in the building, the likelihood of electrical damage rises sharply. Typical patterns include a printer that will not connect even with a known-good cable, several functions failing together, a blown fuse, or a burning smell from the electronics compartment. In these cases, switch off, do not keep restarting the machine, and have the incoming supply, stabiliser or UPS, power supply unit and main board checked. Also check the PC’s network port, which can be damaged by the same surge. Our article on lightning, surges and earthing faults explains how these events damage main boards and how to prevent them.
What to tell your technician
- Printer model, board brand and version, software version.
- Exact symptoms and error codes, with screenshots and photos.
- When the fault started and what happened just before.
- Whether the fault is constant or intermittent.
- Checks already done and their results.
Good information often allows the technician to arrive with the right part or to fix a configuration problem remotely.
Do not ignore early warning signs
Many main board failures are preceded by small warnings: an occasional connection drop, a sensor error that clears on restart, a heater that is slow to reach temperature, or a carriage that sometimes hesitates. These are easy to ignore during busy periods, but they often point to a developing problem with connectors, power, mechanics or the board itself. Recording and investigating early signs costs far less than an emergency breakdown during peak season.
Further reading: The triage order below follows standard troubleshooting logic: rule out the simple causes first.
Key takeaways
- Main board faults appear as control problems: connection, initialisation, motion, feeding, heaters, cleaning, sensors, parameters and restarts.
- Each symptom has common non-board causes that should be checked first.
- Motor driver failures often follow mechanical overload; fix mechanics before replacing boards.
- Error codes identify the failed function, not necessarily the failed part.
- Several unrelated functions failing together suggests the board, power supply or earthing.
If your printer shows any of these symptoms, the Unified Engineering Dynamics team can help you narrow down the cause and decide whether the main board is really at fault.
More in the main board series
This article is part of our series on eco-solvent printer main boards. Continue with the other guides:
- Eco-Solvent Printer Main Board: Functions, Ports and Common Failure Points
- Hoson vs Senyang vs BYHX Main Boards: Which Board Kit Suits Your Printer?
- Main Board Firmware Updates: When to Update, Risks and Backup Steps
- Board Kit Upgrade: Converting an XP600 Printer to i3200 (Main + Head Board Changes)
- Network Port and USB Problems on Main Boards: Faults Operators Can Fix Themselves
- Main Board Replacement Checklist: Dongle, Software Licence, Maintop/PhotoPrint Settings
- Lightning, Surges and Earthing Faults: Why Main Boards Die in Monsoon Season
- Eco-Solvent Main Board Price in India: XP600, i3200, DX5 Kits Compared
- Buying a Second-Hand Eco-Solvent Printer? How to Check the Main Board and Electronics
Related: our head carriage board series starts with the head carriage board explained, and our fire board series starts with what a fire board is and what it does. For a side-by-side view of all three boards, read fire board vs head board vs mainboard.
For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.
Frequently Asked Questions
My printer is not connecting to the PC. Is the main board faulty?
Not usually. Most connection problems are caused by PC network settings, firewall, cables or software. Check these first; suspect the board if link lights stay off with a known-good cable and PC, especially after a storm.
Why does my carriage not move?
Common causes are mechanical resistance, belt problems, encoder faults, damaged motor cables or a failed motor. A failed motor driver on the main board is possible, often caused by mechanical overload.
Can a main board fault stop the heaters?
Yes, but heater problems are more often caused by failed elements, temperature sensors, relays, fuses or wiring. These should be checked by qualified personnel.
What does it mean if several functions fail at once?
It suggests a shared cause such as the main board, the power supply or an earthing problem, especially after a power event.
Where can I find the meaning of my printer’s error codes?
Check your machine manual, the software help, or ask your supplier for the error code list for your board system. Codes differ between systems.
Why do my settings reset after switching off?
Possible causes include software reinstallation, power cuts during saving, interrupted firmware updates or a memory fault on the board.