Direct answer: Update your eco-solvent printer’s main board firmware only when there is a clear reason: your board or machine supplier recommends it to fix a known problem, a replacement carriage board or new head type needs it, or a new software version requires it. Do not update simply because a newer file exists. Firmware updates carry real risks: an interrupted update can leave the board unable to start, the wrong file can make it misbehave, and a new version may reset parameters or require matching updates to the carriage board and print control software. A safe update means getting the exact file for your board model and version from a trusted source, backing up all parameters and calibration values, using stable power on a UPS, following the supplier’s procedure without interruption, and verifying and recalibrating afterwards.
A main board firmware update should always start with a clear reason and a complete backup.

Table of Contents
This guide explains what firmware does, when updating is worthwhile, the risks, how to back up, a step-by-step safe procedure, and how to recover from a failed update. It is part of our main board series; see main board functions and failure points for background.
What firmware is and what it controls
Firmware is the software stored inside the main board (and also on the carriage board) that runs the machine. It is different from the print control software on your PC. Firmware handles:
- Communication with the PC and print control software.
- Motor control, acceleration profiles and positioning.
- Heater control and temperature management.
- Sensor reading and error handling.
- Data transfer to the carriage board.
- Support for specific head types, head counts and print modes.
- Storage and use of machine parameters.
Because it controls so much, a firmware change can affect almost every aspect of the machine’s behaviour, for better or worse.
Firmware, carriage board and software must match
In most board systems, three pieces must work together:
| Component | Where it runs | Must match |
|---|---|---|
| Main board firmware | Main board | Carriage board firmware and print control software |
| Carriage board firmware | Carriage (head) board | Main board firmware and head type |
| Print control software | PC | Main board firmware version |
Updating one without the others can cause communication errors, missing features or unstable behaviour. Before any update, ask the supplier whether the carriage board firmware and the PC software also need updating, and get all the matching files together.
Good reasons to update
- Supplier-recommended fix: the board maker or machine supplier has identified a bug that affects your machine, such as a heater control issue or a communication problem, and recommends a specific firmware version.
- New carriage board: a replacement or upgraded carriage board requires a newer main board firmware.
- New head type or head count: an upgrade, such as adding a second head or moving to i3200, needs firmware that supports the new configuration.
- Software requirement: a newer print control software version you need only works with newer firmware.
- Feature you actually need: a new feature that solves a real production problem, confirmed by the supplier to work on your board.
Poor reasons to update
- A newer file exists online, but your machine works well.
- Someone on a forum or social media group says the new version is “better”.
- Hoping an update will fix a print quality problem that has not been diagnosed.
- Trying firmware from another machine or another board version.
If the machine is working well, the safest firmware is usually the one already installed.
The risks of updating
| Risk | What can happen | How to reduce it |
|---|---|---|
| Interrupted update | Board cannot start; may need reprogramming by supplier | Online UPS, stable connection, do not touch during update |
| Wrong file | Board misbehaves, wrong head support, motor or heater problems | Use exact file for your board model and version, from trusted source |
| Parameter reset | Calibration, head settings and machine settings lost | Back up everything first |
| Mismatch with carriage board or software | Communication errors, heads not detected | Update matching components together as advised |
| New behaviour | Changes in motion, timing or colour output | Recalibrate and test after update |
| Licence or lock issues | Machine requires reactivation | Check with manufacturer before updating |
| No rollback | Cannot return to the old version easily | Keep old firmware files and ask supplier about rollback |
Before you update: preparation
1. Confirm the need
Write down why you are updating and what you expect to change. Ask the supplier to confirm that the update addresses your issue and is suitable for your exact board.
2. Get the right files
Obtain firmware files from the board maker, an authorised distributor or your machine supplier, specifically for your main board model and version. Ask for matching carriage board firmware and print control software if needed, and for written update instructions. Avoid files from unknown websites or shared without version information.
3. Record current versions
Screenshot the current firmware and software versions. Keep the current firmware files if available, so you have a reference and possibly a rollback option.
4. Back up parameters
Back up everything the software allows. Typical items include:
- Machine parameter files, if the software can export them.
- Head voltage values and head type settings.
- Head alignment values: vertical, head-to-head, bidirectional.
- Media feed calibration values for each media.
- Heater temperatures and drying settings.
- Cleaning settings and schedules.
- Origin offsets, print area and machine width settings.
- Network settings of the printer.
Where the software does not export settings, photograph each settings screen. Store backups on the PC and on a second device such as a USB drive or cloud storage.
5. Check activation and licences
Ask whether the update will require reactivation of the board or software, and make sure you have the codes or contact details needed.
6. Plan the timing
Schedule the update when you can afford downtime, not in the middle of an urgent order. Allow time for recalibration and testing.
Safe main board firmware update procedure
Exact steps vary by board system; always follow the supplier’s instructions. A general safe procedure is:
- Connect the printer and PC to an online UPS or confirm very stable power.
- Close all other programs on the PC. Disable sleep, screen savers and automatic Windows updates for the duration.
- Use a direct, short network or USB cable between PC and printer.
- Ensure heads are capped and the printer is idle, with no job in progress.
- Start the update tool or menu as instructed and select the correct file.
- Confirm the file name and version once more before starting.
- Start the update and do not touch the PC, printer or cables until it is complete.
- Wait for the confirmation message. Some updates take several minutes and may restart the board.
- Restart the printer and software as instructed.
- Check the new firmware version in the software.
- Update carriage board firmware and PC software in the order the supplier specifies, if required.
Never update firmware during a storm, during known voltage fluctuations, or on a laptop with a weak battery.
After the update: verification and recalibration
- Check that all heads are detected and settings for head type and voltage are correct; re-enter them if reset.
- Check machine parameters against your backup and restore any that changed.
- Run initialisation and check carriage and feed movement.
- Check heaters reach their set temperatures.
- Run a cleaning cycle and nozzle check.
- Recalibrate head alignment, bidirectional alignment and media feed.
- Print a colour reference and compare with an earlier print.
- Run a production job and monitor for unusual behaviour.
- Record the new versions and the date in the machine log.
For calibration steps, our carriage board replacement checklist includes a full calibration sequence that also applies after firmware updates.
If the update fails
If the update stops partway, the board does not restart, or the machine behaves abnormally afterwards:
- Do not repeatedly power cycle or try random files.
- Note exactly what happened: at what percentage or step the update stopped, any error messages.
- Contact the supplier with this information. Many board systems have a recovery procedure for interrupted updates.
- If a recovery procedure is provided, follow it carefully on stable power.
- If the board cannot be recovered on site, it may need reprogramming by the supplier or a qualified repairer.
- Once recovered, restore parameters from your backup and recalibrate.
This is where your preparation pays off: with correct files, backups and supplier contact details, recovery is usually manageable.
Firmware and head voltage settings
Firmware updates can reset head settings to defaults. Running heads on default values instead of their label values can overdrive or underdrive them. After every firmware update, check head type and voltage values immediately, before printing. Our article on head voltage settings explains why this matters.
Firmware and RIP software
Your RIP software, such as Maintop or PhotoPrint, sends jobs through the print control software. A firmware update rarely affects the RIP directly, but a new print control software version may change how the RIP connects or which printer driver is needed. Check that your RIP still prints correctly after the update, and ask your RIP supplier if a driver update is required.
Reading firmware version numbers
Firmware versions are usually shown as numbers such as 2.1.5 or with dates and letter codes. Different board makers use different formats, but a few general points help:
- The first number often indicates a major generation; a change here usually means significant changes and stricter matching with carriage boards and software.
- Later numbers usually indicate smaller fixes within a generation.
- Some versions are specific to a head type or head count, even if the numbers look similar.
- Machine manufacturers sometimes use customised versions with their own codes.
Never assume a higher number is suitable for your board. Always confirm with the supplier that a version is intended for your exact board model, head type and machine.
Keep a firmware archive
Create a folder on the PC, with a backup copy on a USB drive or cloud storage, containing:
- The firmware files currently installed on the main board and carriage board, if available.
- The print control software installer for the current version.
- Parameter backups with dates.
- Screenshots of settings screens.
- Any update instructions and release notes received from the supplier.
Label each item with the date and version. This archive turns a failed update, a PC crash or a board replacement from a crisis into a routine job.
Common myths about firmware updates
“New firmware improves print quality”
Occasionally a new version improves waveforms or motion, but most print quality problems come from clogging, ink, calibration, mechanics or settings. Updating firmware to fix an undiagnosed quality problem rarely works and adds risk.
“Firmware from a friend’s machine will work”
Even machines that look identical may use different board versions or customised firmware. Using another machine’s file can cause errors or damage.
“If the update fails, the board is finished”
Many interrupted updates can be recovered with the correct procedure from the supplier. Do not panic, and do not try random files; contact the supplier.
“Updating once means I must keep updating”
No. Once your machine is stable on a suitable version, you can stay on it until there is a clear reason to change.
Who should perform updates
Because of the risks, firmware updates are best done by the machine supplier’s technician or an experienced technician familiar with your board system. Shop owners can perform updates if the supplier provides clear instructions and support, but operators should not update firmware without authorisation. Set a clear rule in the shop.
Firmware after a main board or carriage board replacement
When a main board or carriage board is replaced, the new board may arrive with a different firmware version from the one on your machine. This is one of the most common reasons for a firmware update. Before installing a replacement board, ask the supplier which firmware version is loaded on it and whether it matches your other board and PC software. If not, plan the update as part of the replacement, with backups and stable power. After installation, check versions on both boards and in the software, restore parameters, and recalibrate. Our carriage board replacement checklist and the main board replacement checklist in this series cover this in detail.
A real-world style example
Consider a shop whose printer started showing an occasional heater error. The operator found a newer firmware file in a social media group and installed it during a busy afternoon, without a backup. The update completed, but head voltage values reset to defaults and alignment values were lost. The next morning, prints showed banding and colour shifts, and the shop spent a day recalibrating. The heater error, it turned out, was caused by a loose heater sensor connector. This illustrative example shows why updates should start with diagnosis, use supplier-approved files, and always include backups.
Firmware update checklist
| # | Task | Done |
|---|---|---|
| 1 | Clear reason for update confirmed with supplier | ☐ |
| 2 | Correct firmware files for exact board model and version obtained | ☐ |
| 3 | Matching carriage board firmware and PC software obtained if needed | ☐ |
| 4 | Current versions recorded | ☐ |
| 5 | All parameters backed up and settings screens photographed | ☐ |
| 6 | Activation and licence requirements checked | ☐ |
| 7 | Online UPS or stable power, direct cable, PC sleep disabled | ☐ |
| 8 | Update completed without interruption | ☐ |
| 9 | New version verified | ☐ |
| 10 | Head type and voltage settings checked | ☐ |
| 11 | Parameters restored and machine recalibrated | ☐ |
| 12 | Production test passed and log updated | ☐ |
Further reading: For a general explanation of what firmware is and how it differs from PC software, see this overview.
Key takeaways
- Update main board firmware only for a clear reason confirmed by your supplier.
- Main board firmware, carriage board firmware and PC software must match.
- Back up all parameters and photograph settings before updating.
- Use the exact files for your board version, stable power and a direct connection, and never interrupt an update.
- After updating, check head settings, restore parameters, recalibrate and test before production.
If you need the correct firmware for your board or help planning a safe update, the Unified Engineering Dynamics team can assist with files, procedures and post-update calibration.
More in the main board series
This article is part of our series on eco-solvent printer main boards. Continue with the other guides:
- Eco-Solvent Printer Main Board: Functions, Ports and Common Failure Points
- Main Board Failure Symptoms: No Connection to PC, Carriage Not Moving, Error Codes
- Hoson vs Senyang vs BYHX Main Boards: Which Board Kit Suits Your Printer?
- Board Kit Upgrade: Converting an XP600 Printer to i3200 (Main + Head Board Changes)
- Network Port and USB Problems on Main Boards: Faults Operators Can Fix Themselves
- Main Board Replacement Checklist: Dongle, Software Licence, Maintop/PhotoPrint Settings
- Lightning, Surges and Earthing Faults: Why Main Boards Die in Monsoon Season
- Eco-Solvent Main Board Price in India: XP600, i3200, DX5 Kits Compared
- Buying a Second-Hand Eco-Solvent Printer? How to Check the Main Board and Electronics
Related: our head carriage board series starts with the head carriage board explained, and our fire board series starts with what a fire board is and what it does. For a side-by-side view of all three boards, read fire board vs head board vs mainboard.
For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.
Frequently Asked Questions
Should I update my printer’s main board firmware regularly?
No. Update only when there is a clear reason, such as a supplier-recommended fix, a new carriage board or head configuration, or a required software version.
What happens if a firmware update is interrupted?
The board may fail to start properly. Contact your supplier for a recovery procedure; in some cases the board must be reprogrammed by the supplier or a repairer.
Will a firmware update erase my settings?
It can. Always back up parameters and photograph settings screens before updating, and check head voltage and calibration afterwards.
Can I use firmware from another printer?
No. Use only firmware for your exact main board model and version, obtained from a trusted source.
Do I need to update the carriage board firmware too?
Sometimes. Main board firmware, carriage board firmware and PC software must match. Ask your supplier which components need updating together.
Does a firmware update affect my RIP software?
Usually not directly, but a new print control software version may require a RIP driver update. Test printing from your RIP after the update.