Eco Solvent Printing, Printheads

Board Kit Upgrade: Converting an XP600 Printer to i3200 (Main + Head Board Changes)

XP600 to i3200 Conversion: Board Kit Upgrade Guide

Direct answer: Converting an XP600 eco-solvent printer to i3200 heads is a complete board kit upgrade, not a head swap. The i3200 needs a carriage board designed for it, and in almost all cases a matching main board, new data and head cables, adapter boards, firmware and print control software. On the mechanical side it also needs an i3200 head plate or carriage modification, suitable dampers, a capping station sized for the i3200, and ink system changes. After installation the machine needs full calibration and new colour profiles. The upgrade can make sense on a machine with a strong frame, good rails and accurate feed, where the owner wants i3200 speed and durability. On a worn or lightly built machine, the total cost of the kit, heads, parts, labour and downtime can approach that of a new i3200 printer that comes with warranty.

An XP600 to i3200 conversion is a full electronics and mechanical project, not a simple head swap.

XP600 to i3200 Conversion: Board Kit Upgrade Guide
XP600 to i3200 Conversion: Board Kit Upgrade Guide

This guide explains why both boards change, lists the parts involved, walks through the process, estimates the cost structure and helps you decide whether conversion or replacement is the better investment. It is part of our main board series. For background on the two heads, see our comparison of i3200 vs XP600 printheads.

Why owners consider the conversion

The XP600 has been the standard entry-level head for years. It is affordable and widely supported, but it has fewer nozzles and generally shorter life in production than the i3200. The i3200 offers more nozzles per head, higher throughput, and greater durability in industrial use. Shops that started with an XP600 machine and now have steady production often want i3200 speed without buying a new machine. The question is whether the conversion delivers that value on their particular printer.

Why the main board usually changes too

Board makers design kits around specific heads. An XP600 kit’s main board is built and programmed for XP600 data rates, nozzle layouts and carriage board protocols. In most cases:

  • No i3200 carriage board exists that works with the XP600 main board version installed.
  • The XP600 main board firmware does not support i3200 configurations.
  • The data link and cable between main board and carriage board differ.
  • Print control software and RIP drivers are configured for the kit as a whole.

Some board systems have main boards that support several head types with different carriage boards, but this must be confirmed for your exact main board model and version. If your supplier cannot confirm it in writing, plan for a full kit. Our article on Hoson vs Senyang vs BYHX main board kits explains how kits are structured.

Full parts list for an XP600 to i3200 conversion

CategoryPartNotes
Electronicsi3200 main boardUsually required; confirm with supplier
Electronicsi3200 carriage board for chosen head countSingle or double head
ElectronicsAdapter or transfer boardsCommon on i3200 systems
ElectronicsData cable(s) and head cablesCorrect type and length for your carriage travel
ElectronicsFirmware, print control software, licenceMatching versions
ElectronicsPower supply check or upgradei3200 kits and heads may need more power
Headsi3200 eco-solvent variant head(s)Correct variant for eco-solvent ink
Mechanicali3200 head plate or carriage modificationPrecise mounting for alignment
MechanicalCapping station for i3200XP600 capping will not seal i3200
MechanicalWiper assemblySized for i3200
Ink systemDampers for i3200Correct type and connectors
Ink systemInk tubes and fittingsMay need more channels or different sizes
Ink systemInk compatible with i3200 eco-solvent headsConfirm with ink and head supplier
SoftwareRIP driver for new configurationMay require update or new licence
ServiceInstallation, calibration, colour profilingSkilled technician required

Mechanical considerations

The i3200 head is physically larger than the XP600 and mounts differently. The carriage must hold the head precisely, at the correct height and angle, with space for dampers, adapter boards and cables. Some carriages can be adapted with a new head plate; others need significant modification or a different carriage. Poor mounting leads to alignment problems and banding that no amount of calibration fully fixes.

Carriage weight may increase, which affects acceleration, belt tension and motor load. The rails, bearings and carriage motor must be in good condition. A carriage that already shows wear on an XP600 machine will struggle more with the heavier i3200 setup and faster production modes. Our guide to carriage belts, rails and bearings helps assess condition.

Capping and cleaning

The capping station must seal the i3200 head completely when parked. An XP600 capping station will not fit or seal an i3200. Without proper capping, the head dries out and loses nozzles quickly, wiping out the benefit of the upgrade. The wiper must also suit the i3200 nozzle plate. Plan these parts from the start. See our capping station guide.

Ink considerations

Use an eco-solvent ink that is suitable for i3200 eco-solvent heads. Ink that worked with your XP600 may or may not be recommended for i3200; check with your ink supplier. Flush and clean the ink system thoroughly during conversion so old ink residue and debris do not enter the new heads. Our eco-solvent ink guide covers ink selection.

The conversion process step by step

  1. Survey the machine: record board system, versions, head count, carriage design, capping station, ink system, PSU rating and mechanical condition.
  2. Confirm the kit: get written confirmation of the complete kit, including main board, carriage board, adapters, cables, firmware and software.
  3. Plan mechanics: head plate, capping station, wiper, dampers and ink lines for i3200.
  4. Back up settings: save existing parameters and RIP settings for reference.
  5. Remove old parts: XP600 heads, carriage board, dampers, capping station and, where required, main board and cables.
  6. Install mechanics: head plate, capping station, wiper, dampers and ink lines; check for leaks.
  7. Install electronics with power off: main board, carriage board, adapters, data and head cables; check routing.
  8. Load firmware and software: configure the machine parameters for your mechanics, including carriage width, motor settings, heaters and sensors.
  9. Set head type and voltage values from each i3200 head’s label.
  10. Prime and test: fill ink, clean, print nozzle checks.
  11. Calibrate: head height, angle, head-to-head alignment, bidirectional alignment and media feed.
  12. Configure the RIP and create new colour profiles for your main media.
  13. Production test: print real jobs and check speed, quality and drying.

Configuring a new main board for an existing machine’s mechanics is a skilled job. Parameters such as motor settings, encoder resolution, heater control and sensor logic must match the hardware. Wrong settings can cause poor motion, errors or damage. This is a key reason to use a technician experienced with the new board system.

Cost structure

Exact prices vary with board brand, head count, supplier and market conditions. The total cost of a conversion typically includes:

Cost elementIndicative range or note
i3200 board kit (main + carriage board, cables, software)Roughly ₹32,000 to ₹70,000 depending on single or double head and brand
i3200 eco-solvent headsSignificant; each head is a major cost item
Head plate, capping station, wiper, dampers, tubesSeveral thousand to tens of thousands of rupees
Power supply upgrade if neededVaries
Installation, configuration, calibration, profilingTechnician time, often one to three days
DowntimeLost production during conversion
RIP driver update or licenceDepends on RIP

See our board price guide for more on kit prices. Add everything up honestly, including heads and downtime, before comparing with a new machine.

Conversion versus a new i3200 machine

FactorConvert existing XP600 machineBuy new i3200 machine
Total costKit, heads, parts, labour, downtimeMachine price
MechanicsExisting rails, motors, feed, heatersAll new, designed for i3200
WarrantyOnly on new parts, if anyFull machine warranty
Integration riskHigher; custom configurationLower; factory configuration
DowntimeMachine out of service during conversionOld machine keeps working
CapacityOne machineTwo machines if you keep the old one
ResaleConverted machines can be harder to sellStandard resale market

Many shop owners find that once heads and labour are included, a new entry-level i3200 machine is not much more expensive, and it brings warranty, factory integration and the option to keep the XP600 machine running for smaller jobs. Conversion is most attractive when the existing machine has a heavy, high-quality frame and mechanics, or when space allows only one machine. Our guide to i3200 printer prices in India provides a comparison baseline.

Is your machine a good candidate?

  • Strong, rigid frame and carriage beam without flex.
  • Rails, bearings and belts in good condition.
  • Accurate, reliable media feed.
  • Heaters working and adequate for faster production.
  • Electronics compartment with space and adequate PSU capacity, or room for an upgrade.
  • A technician experienced with i3200 kits and your machine type available.
  • Enough steady work to justify the investment.

If several of these are missing, a new machine is usually the safer choice.

Single or double i3200 for the conversion?

A conversion is a good moment to decide on head count. A single i3200 already offers a substantial speed increase over a single XP600 in many modes. A double i3200 setup increases speed further but adds the cost of a second head, a larger carriage board, a two-head capping station and more ink channels, and it puts more load on the carriage motor and frame. For many shops moving from one XP600, a single i3200 delivers a large improvement at a manageable cost. Shops with heavy production may justify double i3200, but should be especially careful that the machine’s mechanics, heaters and power supply can support it. Our comparison of single head vs double head eco-solvent printers helps with this decision.

Questions to ask the conversion technician

  • Have you converted this machine model, or similar models, to i3200 before?
  • Which board kit will you use, and can you confirm it supports my machine’s motors, encoders and heaters?
  • Which mechanical parts will be replaced or modified, and who supplies them?
  • Is my power supply adequate, or will it need upgrading?
  • How will you configure machine parameters, and will you give me a backup afterwards?
  • Is calibration and colour profiling included?
  • What warranty do you give on parts and work?
  • How many days will the machine be out of production, and what happens if parts are missing?

What to expect in the first weeks after conversion

Even a well-executed conversion needs a settling-in period. In the first weeks, expect some fine-tuning of feed calibration for different media, adjustments to heater settings for the faster production speeds, possible refinement of colour profiles, and close monitoring of nozzle health as the new heads and capping station bed in. Print nozzle checks daily and keep a log. Report any recurring errors to the technician promptly; early adjustments are easier than fixing problems that have been allowed to continue. Agree in advance that the technician will provide follow-up support during this period.

What to do with the old XP600 parts

Keep the old XP600 boards and heads, at least until the conversion is stable. If the conversion runs into problems, they may be useful for reverting temporarily. Later, working XP600 boards and heads can be kept as spares for another XP600 machine or sold. Store them in antistatic bags, and cap or flush the heads properly if you intend to keep them usable.

Risks to manage

  • Configuration errors in motor, encoder and heater parameters causing poor motion or errors.
  • Alignment problems from imprecise head mounting.
  • Capping failures leading to dried heads.
  • Ink incompatibility damaging new heads.
  • Power supply overload causing instability.
  • Extended downtime if parts are missing or problems arise.
  • Warranty loss on the existing machine.

Plan carefully, get all parts confirmed before starting, and agree a clear scope and timeline with the technician.

Example decision scenarios

Scenario 1: A shop has a heavy, well-built 1.8 metre XP600 machine with excellent rails and feed, steady daily production and limited floor space. A single i3200 conversion with a full board kit and new capping station makes sense, provided an experienced technician is available.

Scenario 2: A shop has a light, older XP600 machine with worn rails, inconsistent feed and occasional control errors. Conversion would mean spending heavily on top of weak mechanics. A new i3200 machine, keeping the XP600 for smaller jobs, is the better choice.

Scenario 3: A shop wants double i3200 speed on a machine originally built for a single XP600, with a modest power supply and heaters. The upgrade risks overloading the carriage, power supply and drying capacity. A new double i3200 machine designed for that load is safer.

These illustrative scenarios show that the right answer depends more on the machine’s condition and the shop’s needs than on the price of the board kit alone.

Further reading: Both heads use piezo inkjet printing technology, but their nozzle counts and data formats differ substantially.

Key takeaways

  • XP600 to i3200 conversion is a full board kit upgrade, usually including the main board, not just new heads.
  • Mechanical changes are needed: head plate, capping station, wiper, dampers and ink lines.
  • Configuring a new main board for existing mechanics requires an experienced technician.
  • Add up kit, heads, parts, labour and downtime, and compare honestly with a new i3200 machine.
  • Conversion suits strong machines in good condition; worn or light machines are usually better replaced.

The Unified Engineering Dynamics team can assess your XP600 machine, quote a complete i3200 conversion, and compare it with new i3200 options so you can choose the best investment.

More in the main board series

This article is part of our series on eco-solvent printer main boards. Continue with the other guides:

Related: our head carriage board series starts with the head carriage board explained, and our fire board series starts with what a fire board is and what it does. For a side-by-side view of all three boards, read fire board vs head board vs mainboard.

For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.

Frequently Asked Questions

Can I put i3200 heads on my XP600 printer by changing only the head board?

Rarely. Most XP600 main boards do not support i3200 carriage boards, so the main board, cables, firmware and software usually change too, along with mechanical parts.

What mechanical parts change in an XP600 to i3200 conversion?

Typically the head plate or carriage mounting, capping station, wiper, dampers and ink lines, plus possibly the power supply.

Is converting to i3200 cheaper than buying a new printer?

Sometimes, especially for strong machines in good condition. Once heads, parts, labour and downtime are included, the cost can approach that of a new entry-level i3200 machine.

Will my existing ink work with i3200?

Not necessarily. Use an eco-solvent ink recommended for i3200 eco-solvent heads, and flush the ink system during conversion.

How long does the conversion take?

Typically one to three days of technician work once all parts are available, plus time for calibration and colour profiling.

Who should perform the conversion?

A technician experienced with i3200 board kits and your machine type, because main board parameters must be configured correctly for the existing mechanics.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *