Eco Solvent Printing

Main Board Replacement Checklist: Dongle, Software Licence, Maintop/PhotoPrint Settings

Main Board Replacement Checklist: 10 Safe Steps

Direct answer: Replacing an eco-solvent printer’s main board involves much more than swapping hardware. Before ordering, confirm the exact board brand, model and version, and whether the board is locked to your machine maker and needs activation. Before removal, back up all machine parameters, head settings, calibration values and network settings, and save your RIP (Maintop or PhotoPrint) printer configurations, colour profiles and job presets. Secure your dongle and licence information, since some RIPs and print control software use USB dongles or activation codes linked to hardware. Install the new board only with the power off and with antistatic precautions. Then load the matching firmware and software, activate the board, restore parameters, set head type and voltage, reconnect the RIP, recalibrate fully and run production tests before normal work resumes.

This main board replacement checklist is designed to be followed step by step by owners and technicians together.

Main Board Replacement Checklist: 10 Safe Steps
Main Board Replacement Checklist: 10 Safe Steps

This checklist is designed for shop owners and technicians to use step by step. It is part of our main board series. For general main board background, see main board functions and failure points.

Step 0: Confirm the main board really needs replacing

Main boards are often blamed for faults caused by PSUs, cables, sensors, motors, PC settings or software. Before ordering a replacement, make sure a technician has checked:

  • Mains supply, stabiliser or UPS, and earthing.
  • Power supply unit output.
  • Network or USB cable, PC settings and software.
  • Connectors and wiring in the electronics compartment.
  • Motors, motor drivers, sensors and heater components.
  • Carriage board and data cable.

Our guides on main board failure symptoms and network and USB problems help rule out common non-board causes. Also consider whether board-level repair is possible; our repair vs replace guide explains the trade-offs.

Step 1: Identify the board precisely

Record the following before ordering:

ItemWhere to find it
Board brand and modelLabel or silkscreen printing on the board
Board version or revisionLabel, silkscreen, or software “about” screen
Firmware versionPrint control software
Carriage board model and versionCarriage board label
Head type and countMachine specification
Machine model and serial numberMachine nameplate
Connector layoutClear photographs of the board in place

Take clear photos of the board, its labels and every connector with cables attached. These photos guide reconnection and help the supplier confirm compatibility. Our article on identifying spares by model and part number gives more tips.

Step 2: Confirm compatibility and activation with the supplier

Send your records and photos to the supplier and ask:

  • Is this replacement the same model and version, or a compatible newer version?
  • Is it compatible with my carriage board and heads?
  • Which firmware version is loaded, and does it match my carriage board and PC software?
  • Is the board locked to a machine maker, and how will it be activated or unlocked?
  • Will my existing print control software and licence work, or is a new version or code needed?
  • What warranty applies, and what conditions void it?

Some machine makers supply main boards that are locked to their machines. A board of the same brand bought elsewhere may not work without activation. Clarify this before payment.

Step 3: Secure dongles and licences

Print control software and RIP software may be protected in several ways:

Protection typeWhat to do before replacement
USB dongle for RIP or print softwareLocate it, label it, keep it safe; note which PC it belongs to
Activation code linked to PC hardwareRecord the code and contact details for reactivation
Board-linked activation or unlock codeGet the procedure and codes from the supplier in advance
Online account licenceRecord login details and check how many activations are allowed

Lost dongles are a common and expensive problem. Many RIP dongles cannot be replaced cheaply, and some cannot be replaced at all without buying a new licence. Keep the dongle attached to the PC in a safe position, record its serial number, and never lend it out.

Step 4: Back up machine parameters and settings

Back up everything the print control software allows, and photograph each settings screen. Typical items include:

  • Machine parameter file (export if possible).
  • Head type, head count and head voltage values for each head.
  • Head alignment values: vertical, head-to-head, bidirectional for each mode.
  • Media feed calibration values for each media type.
  • Heater temperature settings.
  • Cleaning settings and automatic cleaning intervals.
  • Origin offsets, print width and margins.
  • Printer network IP address and PC adapter settings.

If the old board is dead and cannot be read, use earlier backups or photos. This is why routine backups matter; see our article on main board firmware updates and backups.

Step 5: Back up RIP settings (Maintop, PhotoPrint and others)

Your RIP holds settings that took time to build. Before replacing the main board, and especially if the PC or print software will also change, back up:

  • Printer setup: the printer model or driver selected, port settings, and output configuration.
  • ICC colour profiles: custom profiles for your media and ink combinations, and the folder they are stored in.
  • Print modes and resolutions configured for each job type.
  • Job presets or queue settings: media sizes, margins, nesting, step and repeat, cut marks.
  • Ink limits and linearisation data, if used.
  • Licence information and dongle details.

Many RIPs let you export profiles and settings; otherwise, copy the relevant folders and take screenshots. After replacement, the RIP may need to be reconnected to the printer through the print control software or a new port setting. Check with your RIP supplier whether the main board change affects RIP configuration.

Step 6: Safe removal and installation

  1. Switch off the printer, disconnect mains power and wait for capacitors to discharge as recommended by the supplier.
  2. Use an antistatic wrist strap connected to a proper earth point.
  3. Label every cable before disconnecting it, using tags that match your photographs.
  4. Release connector latches and pull by the connector body, never the wires.
  5. Remove the old board and place it in an antistatic bag.
  6. Inspect the compartment for dust, burnt smells, damaged wiring or loose terminals, and clean as needed.
  7. Handle the new board by its edges and check it for physical damage.
  8. Mount the new board securely with all mounting screws and any insulating spacers.
  9. Reconnect cables exactly as recorded, checking orientation and seating.
  10. Double-check every connector against your photos before power is restored.

Our guide to connector handling rules applies equally to main boards.

Step 7: First power-on and configuration

  1. Restore power through a stable, protected supply.
  2. Watch for normal start-up behaviour, and switch off immediately if there is smoke, a burning smell or abnormal noise.
  3. Connect the PC with the recorded network or USB settings.
  4. Load or verify firmware, and confirm versions match the carriage board and software.
  5. Complete board activation or unlock procedures as instructed by the supplier.
  6. Restore machine parameters from your backup, or re-enter them from photos.
  7. Set head type, head count and head voltage values from the head labels.

Step 8: Calibration and testing

  1. Run initialisation and confirm carriage and media movement are smooth.
  2. Check all sensors: media, origin, cover, and any others.
  3. Check heaters reach and hold their set temperatures.
  4. Run cleaning and print a nozzle check.
  5. Calibrate head alignment, bidirectional alignment and media feed.
  6. Reconnect the RIP and print a colour reference using your existing profile.
  7. Compare with a previous print; re-profile if colours have shifted significantly.
  8. Run a production job and monitor closely.

Step 9: Record and close

  • Record the new board’s model, version, serial number, firmware version and date of installation.
  • Save a fresh parameter backup from the new board.
  • File the warranty card and invoice.
  • Note the cause of failure, if known, and corrective actions such as improved earthing or surge protection.

Preventing the next failure

If the old board failed due to a surge, overheating, ink contamination or a connector fault, fix the cause before or during replacement. Otherwise, the new board may fail in the same way. Check earthing and surge protection, the condition of the stabiliser or UPS, the cooling fans and filters, and the cleanliness of the electronics compartment. Our article on lightning, surges and earthing faults in this series and our stabiliser, UPS and earthing guide cover prevention.

Complete main board replacement checklist

#TaskDone
1Fault confirmed as main board; other causes ruled out☐
2Board brand, model, version, firmware and connectors recorded and photographed☐
3Compatibility, firmware and activation confirmed with supplier☐
4Dongles located and licence codes recorded☐
5Machine parameters backed up and settings photographed☐
6RIP printer setup, ICC profiles and presets backed up☐
7Power off, discharge wait, antistatic precautions☐
8Cables labelled, board removed, compartment inspected and cleaned☐
9New board installed and cables reconnected per photos☐
10Firmware verified, board activated☐
11Parameters restored, head type and voltage set☐
12Sensors, heaters, motion checked☐
13Nozzle check, alignment and feed calibration done☐
14RIP reconnected, colour checked☐
15Production test passed, records and backups updated☐
16Root cause addressed☐

If the PC is also being replaced

Main board failures caused by surges sometimes damage the PC as well, or the shop decides to upgrade the PC at the same time. Changing both together doubles the number of things that can go wrong, so plan carefully:

  • Install the print control software and RIP on the new PC using the original installers and versions that match the board firmware.
  • Transfer or reactivate RIP licences according to the RIP supplier’s procedure; some activations are tied to PC hardware.
  • Move the dongle to the new PC and confirm it is recognised.
  • Copy ICC profiles, presets and job templates to the correct folders on the new PC.
  • Configure the network adapter with the recorded IP settings and add firewall exceptions.
  • Disable sleep and power saving on the new PC’s network adapter and USB ports.
  • Control Windows updates so they do not restart the PC during production.

If possible, set up and test the new PC with the software before the machine returns to service, so only the main board is new on the day of installation.

Locked boards and activation in practice

Some machine makers lock their main boards so that only their own software or boards will work, or so that boards must be activated with a code after installation. In practice this means:

  • You may need to buy the replacement from the machine maker or their authorised dealer.
  • The supplier may need your machine serial number and a code shown by the software to generate an activation key.
  • Activation can be delayed if the supplier is unavailable, for example on holidays or across time zones.
  • Unofficial unlocking can void warranties and cause instability; avoid it.

Ask about activation before the old board fails, so you know the process and contacts in advance. Keep a written record of activation steps in the machine file.

Who should do the replacement

Main board replacement involves mains-powered equipment, static-sensitive electronics, firmware and machine configuration. It should be carried out by a qualified technician familiar with your board system. Shop staff can prepare by collecting information, backing up settings and protecting dongles, which shortens the technician’s visit and reduces the chance of errors.

Common mistakes during main board replacement

  • Ordering a board of the same brand without confirming version and lock status.
  • Not backing up parameters while the old board still worked.
  • Losing the RIP dongle or licence code during PC changes.
  • Reconnecting cables without labels or photos.
  • Printing before setting head type and voltage values.
  • Skipping calibration and blaming the new board for banding.
  • Ignoring the cause of the original failure.

How long does a main board replacement take?

With the correct board in hand, backups ready and a technician familiar with the system, physical replacement usually takes an hour or two. Firmware, activation, parameter restoration and calibration can add several more hours, and colour checks and a production test add more. Plan for the machine to be out of service for most of a working day, longer if activation must wait for the supplier or if the PC is also changed. The biggest delays usually come from ordering the wrong board, waiting for parts, or missing backups and licences, all of which this checklist is designed to prevent.

Keep a machine file

Keep a simple folder, paper or digital, for each machine containing board models and versions, firmware versions, parameter backups, RIP profile backups, dongle serial numbers, licence codes, supplier contacts, invoices and warranty cards. Update it after every repair. When the next board failure happens, this file turns a stressful emergency into a routine job.

Further reading: Your Maintop or PhotoPrint software is a raster image processor (RIP); its settings live on the PC, not the board.

Key takeaways

  • Confirm the fault is the main board, and identify the board precisely before ordering.
  • Clarify locking and activation with the supplier before payment.
  • Protect dongles and licence codes, and back up machine and RIP settings.
  • Install with power off and antistatic precautions, reconnecting cables exactly as photographed.
  • Restore parameters, set head voltages, recalibrate and fix the root cause before resuming production.

The Unified Engineering Dynamics team can help identify your main board, source a compatible replacement, guide activation and calibrate the machine afterwards so you return to production quickly.

More in the main board series

This article is part of our series on eco-solvent printer main boards. Continue with the other guides:

Related: our head carriage board series starts with the head carriage board explained, and our fire board series starts with what a fire board is and what it does. For a side-by-side view of all three boards, read fire board vs head board vs mainboard.

For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.

Frequently Asked Questions

Can I buy any main board of the same brand as a replacement?

Not necessarily. Model, version, firmware and lock status must match your machine and carriage board. Some boards are locked to a machine maker and need activation.

What is a dongle and why does it matter?

A dongle is a USB key that protects RIP or print control software licences. If lost, the software may stop working and replacement can be costly, so keep it safe and record its details.

Will my Maintop or PhotoPrint settings be lost when the main board is replaced?

The RIP settings are stored on the PC, not the main board, but the printer connection may need reconfiguring. Back up profiles, printer setup and presets before any change.

What settings should I back up before replacing the main board?

Machine parameters, head type and voltage, alignment values, feed calibration, heater settings, cleaning settings, print area and network settings.

Do I need to recalibrate after replacing the main board?

Yes. Run head alignment, bidirectional and feed calibration, check heaters and sensors, and verify colour before production.

Why did my new main board fail quickly?

Often because the original cause, such as surges, poor earthing, overheating or a shorted component, was not fixed. Address the root cause during replacement.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *