Eco Solvent Printing

Lightning, Surges and Earthing Faults: Why Main Boards Die in Monsoon Season

Main Board Damage in Monsoon: Surge & Earthing Fixes

Direct answer: Eco-solvent printer main boards fail more often during the monsoon because storms bring lightning-induced surges on power and network lines, frequent power cuts and grid switching cause voltage spikes when supply returns, and humidity worsens poor earthing and corrodes connections. The main board is especially exposed because it connects to everything: mains power through the power supply, the PC through network or USB cables, and the carriage board, motors, heaters and sensors. A surge can enter through any of these paths. Protection is layered: a proper, tested earth; surge protection at the distribution board and at the machine; a good stabiliser and an online UPS for the electronics; PC and printer on the same protected supply; and simple operating rules such as switching off and unplugging during heavy storms and waiting a few minutes after power returns before switching machines back on.

Most monsoon main board damage is preventable with layered protection and a simple storm routine.

Main Board Damage in Monsoon: Surge & Earthing Fixes
Main Board Damage in Monsoon: Surge & Earthing Fixes

This guide explains how surges and earthing faults damage main boards, how to recognise surge damage, and a practical protection plan for Indian print shops. It is part of our main board series. Our fire board series has a related article on power fluctuation and fire board damage.

Why the monsoon is risky for printer electronics

Monsoon factorEffect on electronics
Lightning strikes near power or network linesHigh-energy surges travel into buildings through mains, network and antenna cables
Frequent power cuts and restorationVoltage spikes and dips when supply returns; machines restarting under unstable conditions
Grid switching and transformer faultsOvervoltage, phase imbalance, neutral faults
Generator changeoverTransients and unstable voltage during switchover
High humidityCondensation, corrosion of connectors, leakage currents on dusty boards
Wet ground conditionsCan change earth resistance; poor earth pits become less effective or unreliable
Water leaksMoisture reaching sockets, distribution boards or the machine

How surges reach the main board

A surge is a very short burst of high voltage. It can reach the main board through several paths:

  • Mains power: the surge passes through the stabiliser and power supply unit. If they cannot absorb it, it reaches the DC rails that feed the main board.
  • Network cable: if the PC and printer are on different supplies or earths, a surge can create a voltage difference between them and flow through the network cable, damaging network ports on the PC, the main board or both.
  • USB cable: similar to network cables, especially with long cables.
  • Earth path: with a poor or shared earth, surges from other equipment can raise the earth potential and push current through sensitive circuits.
  • Heater and motor circuits: surges or faults in high-power circuits can couple into control circuits on the main board.

This explains why surge damage often affects communication ports first: the network or USB port sits between two separately powered devices.

The role of earthing

A proper earth gives surge current and fault current a safe, low-resistance path to ground, and provides a stable reference for electronics. Common earthing problems in Indian shops include:

  • No dedicated earth for the machine; reliance on building earth of unknown quality.
  • Earth pits that have dried out or corroded and were never tested.
  • Earth wire not connected at the socket, or sockets without an earth pin connected.
  • Neutral and earth connected together incorrectly.
  • Different equipment using different earths, creating voltage differences.
  • Earth shared with heavy machinery that injects noise.

An electrician should measure earth resistance and the voltage between neutral and earth, and verify that every socket used by the printer and PC is correctly earthed. Our stabiliser, UPS and earthing guide explains what to ask for.

Signs of surge or earthing main board damage

Typical symptoms after a storm or power event include:

  • The printer powers on but the PC cannot connect, even with a known-good cable and settings.
  • The PC’s network port also stops working.
  • The printer does not power on at all, or fuses blow.
  • A burning smell from the electronics compartment.
  • Several unrelated functions fail together: motors, heaters and sensors.
  • Intermittent faults and random restarts that were not present before.
  • Visible damage on inspection by a technician: burnt components, discoloured areas, swollen capacitors.

Surge damage can also be partial: a component may be weakened and fail days or weeks later. Record storm events and any faults that follow, as this helps diagnosis and warranty discussions. For a full symptom guide, see main board failure symptoms.

What to do after a suspected surge

  1. Switch off the printer and PC, and disconnect them from mains.
  2. Do not keep restarting the machine to “see if it works”; repeated power-on can worsen damage.
  3. Check for burning smells, smoke marks or water ingress, without opening electrical compartments yourself.
  4. Have an electrician check the incoming supply, earthing, stabiliser and UPS before reconnecting.
  5. Have a printer technician check the PSU, main board, carriage board and ports.
  6. Test the PC’s network port and the printer connection with a known-good PC and cable.
  7. Record the event and findings for insurance and warranty purposes.

A practical protection plan

Layer 1: Proper earthing

Install or verify a dedicated, properly constructed earth for your printing equipment. Have it tested periodically, especially before the monsoon. Ensure all sockets used by printers, PCs and stabilisers are correctly earthed.

Layer 2: Surge protection at the distribution board

Ask a qualified electrician about installing a suitable surge protection device (SPD) at the main distribution board or at the sub-board feeding your printing equipment. It diverts large surges before they reach your machines. The SPD type and rating should be selected by the electrician for your installation.

Layer 3: Stabiliser and online UPS

A good-quality servo stabiliser sized correctly for the machine handles slow voltage variations. An online UPS for the electronics, the PC and, where practical, the printer’s control circuits, provides clean, stable power and ride-through during short cuts. Heater loads are often too large for a UPS and may be fed separately according to the manufacturer’s guidance.

Layer 4: Point-of-use surge protection

Use quality surge-protected power strips for the PC and accessories, and keep the PC and printer on the same protected supply and earth to avoid voltage differences across the communication cable.

Layer 5: Protect communication cables

Keep network and USB cables short and direct. If a long network run is unavoidable, ask about network surge protectors. Avoid running communication cables alongside power cables or outside the building.

Layer 6: Operating rules

  • During heavy thunderstorms with lightning nearby, finish or pause jobs, switch off the printer and PC, and unplug them if possible.
  • After a power cut, wait a few minutes for supply to stabilise before switching on machines.
  • Switch on the stabiliser first, then UPS, then PC, then printer; switch off in reverse order.
  • Do not run printers during known periods of severe voltage fluctuation.
  • Keep the electronics compartment closed, dry and clean.

Humidity and corrosion

High humidity in monsoon months can cause condensation on cold electronics, especially when air conditioning is switched off overnight and the shop warms and humidifies in the morning. Moisture combined with dust and ink residue can create leakage paths on boards and corrode connectors. To reduce risk:

  • Keep the shop’s humidity and temperature as stable as practical; avoid large daily swings.
  • Allow machines to acclimatise after cold, humid nights before switching on.
  • Keep the electronics compartment clean and filters in good condition.
  • Fix roof and wall leaks near machines and power points.
  • Consider a dehumidifier in very humid locations.

Pre-monsoon electrical check

#CheckByDone
1Earth resistance measured and recordedElectrician☐
2Neutral-earth voltage checked at machine socketsElectrician☐
3All sockets for printer and PC correctly earthedElectrician☐
4Surge protection device at distribution board checkedElectrician☐
5Stabiliser output and relays checkedElectrician or technician☐
6UPS batteries and transfer testedUPS service☐
7PC and printer on same protected supplyShop owner☐
8Communication cables short, direct and away from power cablesShop owner☐
9Electronics compartment cleaned, fans and filters servicedTechnician☐
10Roof and wall leaks near machines fixedShop owner☐
11Parameter and RIP settings backed upOperator☐
12Storm operating rules explained to staffShop owner☐

Generators and inverter changeover

Many Indian shops use a diesel generator or a large inverter during power cuts. The changeover moment is a common source of trouble. When supply switches from grid to generator and back, there can be a brief interruption, a voltage spike or a period of unstable frequency and voltage while the generator settles. Small generators may also produce poor-quality output under varying load, especially when heaters cycle on and off.

To reduce risk:

  • Use an online UPS for the printer electronics and PC, so changeover does not reach them directly.
  • Ensure the generator is sized for the load, including heater surges, and is properly earthed.
  • Prefer automatic changeover systems installed by a qualified electrician, with correct neutral and earth arrangements.
  • Avoid starting large loads, such as air conditioners and compressors, at the same moment as the changeover.
  • If changeover is manual, pause printing and switch off machines before switching supply, then restart once the generator is stable.

Other equipment on the same supply

Air conditioners, compressors, welding machines, laminators and large motors switching on and off create voltage dips and spikes on the shop’s wiring. If the printer shares a circuit with such equipment, these disturbances reach it every day, not just during storms. Ask an electrician to place printers and PCs on a dedicated circuit fed from the distribution board, separate from heavy motor loads, with its own surge protection and a good earth. Look for patterns: if errors happen when the air conditioner starts, the supply arrangement needs attention.

Common mistakes in power protection

  • Buying a stabiliser and assuming it protects against surges.
  • Using cheap power strips labelled as surge protectors without real protection components.
  • Plugging the PC into a wall socket and the printer into a stabiliser on a different earth.
  • Never testing the earth pit after installation.
  • Connecting earth to neutral to “fix” an earth problem, which is dangerous and must never be done.
  • Letting UPS batteries age until the UPS fails during a power cut.
  • Restarting machines immediately after power returns, while voltage is still unstable.

Cost of protection versus cost of damage

A single surge event can damage a main board, carriage board, power supply, PC network port and even printheads. Replacement parts, technician visits and downtime during the busy pre-festival season can add up to a large sum. In comparison, proper earthing, surge protection and a good UPS are a one-time investment with modest maintenance. For most shops, protection pays for itself the first time it prevents a major failure.

A storm-day routine for staff

Operators make the decisions in the moment, so give them a simple routine they can follow without waiting for the owner:

  1. When thunder is heard nearby or the power starts flickering, stop starting new jobs.
  2. Let the current job finish if it is close to completion; otherwise pause it safely.
  3. Park and cap the heads.
  4. Switch off the printer, then the PC, then the UPS and stabiliser.
  5. Unplug the printer and PC from the wall if it is safe to do so.
  6. Wait until the storm has passed and power has been stable for several minutes.
  7. Switch on in order: stabiliser, UPS, PC, printer.
  8. Run a nozzle check and note any errors in the machine log.

Print this routine and fix it near the machine. A few minutes of lost production is far cheaper than a damaged main board.

Insurance and warranty

Many board and machine warranties exclude damage from surges, lightning and poor electrical installation. Check your warranty terms. Consider equipment insurance that covers electrical damage and keep records of your earthing tests, surge protection and UPS maintenance, since insurers and suppliers may ask for them. Our warranty and AMC guide explains common exclusions.

An illustrative example

Consider a shop in a city with heavy monsoon storms. Its printer and PC were plugged into different wall sockets, the earth pit had not been tested since installation, and a long network cable ran across the shop floor. After a nearby lightning strike, the PC could no longer connect to the printer. The PC’s network port and the printer main board’s network port were both damaged, and the shop lost several days of production during the busiest season. After repairs, the shop had its earth tested and improved, installed surge protection at the distribution board, put the PC and printer on the same online UPS, shortened the network cable and adopted a storm-day routine. This illustrative example reflects a common pattern seen in print shops, and shows how simple measures can prevent repeat failures.

Keep a power event log

Keep a simple log next to the machine noting the date and time of storms, power cuts, voltage problems, generator changeovers and any errors that follow. Over a season, the log reveals patterns that help your electrician and technician improve protection, and it provides evidence for warranty or insurance discussions if a board fails.

Further reading: For background on how surge protective devices divert spikes, see this overview of surge protectors.

Key takeaways

  • Monsoon storms, power cuts, grid switching and humidity make main board failures more likely.
  • Surges enter through mains, network and USB cables and poor earth paths; communication ports are often damaged first.
  • Protect in layers: proper earthing, distribution board surge protection, stabiliser and online UPS, point-of-use protection and good cable practice.
  • Switch off and unplug during heavy storms, and wait for stable power before restarting.
  • Do a pre-monsoon electrical check every year and keep records.

The Unified Engineering Dynamics team can review your electrical set-up, recommend protection for your printing machines, and help diagnose and repair surge-damaged boards.

More in the main board series

This article is part of our series on eco-solvent printer main boards. Continue with the other guides:

Related: our head carriage board series starts with the head carriage board explained, and our fire board series starts with what a fire board is and what it does. For a side-by-side view of all three boards, read fire board vs head board vs mainboard.

For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.

Frequently Asked Questions

Why do printer main boards fail more often during monsoon?

Lightning-induced surges, frequent power cuts and restoration spikes, grid switching, and humidity combined with poor earthing all increase stress on electronics.

Can lightning damage my printer through the network cable?

Yes. If the PC and printer are on different supplies or earths, a surge can create a voltage difference across the network cable and damage ports on both devices.

Is a stabiliser enough to protect my printer?

No. A stabiliser handles slow voltage variations but not fast surges. Combine it with proper earthing, surge protection and an online UPS for the electronics.

What should I do during a heavy thunderstorm?

Pause printing, switch off the printer and PC, and unplug them if possible. After power returns, wait a few minutes for supply to stabilise before switching on.

How do I know if my main board has surge damage?

Common signs after a storm include no PC connection with known-good cables, a failed PC network port, no power, blown fuses, a burning smell or several functions failing together.

Does warranty cover surge damage?

Often not. Many warranties exclude surge and lightning damage. Check your terms and consider equipment insurance that covers electrical damage.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *