Direct answer: The core UV flatbed main board functions are receiving print data from the RIP PC over USB or Ethernet, buffering it, synchronising it with the X-axis encoder, controlling the X, Y and Z motors through their drivers, reading limit, height, collision and vacuum sensors, switching the UV LED lamps, ink supply and white circulation, and passing data and timing to the carriage or head boards over the data cable. Each of these jobs has its own port. Knowing which port does what lets you trace most “dead printer”, “no communication” and “carriage won’t move” faults to a cable, a sensor, a power supply or the board itself before you spend money on a new main board.
Learning the UV flatbed main board functions and ports is the fastest way to tell a genuine board fault from a cable, sensor or power supply problem.

Table of Contents
Whether your machine is an A3 desktop i3200 flatbed, an A2 or 6090 XP600 machine, or a 2513 or 3020 industrial flatbed with Ricoh Gen5 or Gen6 heads, the main board sits at the centre of the electronics. This guide explains its functions in plain language, walks through every common port, and shows how to use that knowledge for fault finding. It builds on our driver board vs main board vs head board guide.
Where the main board sits in a UV flatbed
On most flatbeds the main board is mounted in the electrical cabinet at one end of the gantry or under the table, close to the power supplies and motor drivers. It does not travel with the carriage. A long data cable, sometimes a fibre or network link on larger machines, connects it to the carriage board or head boards that ride above the table. This separation is why many faults that look like “the main board is dead” are really cable or carriage faults, and the reverse.
Hoson, Senyang and BYHX all use this broad layout, though board names differ. Hoson calls it the main board or mother board; BYHX systems on Ricoh and Konica machines often call it the main board with separate motion control and head boards. Some A3 machines combine main and head functions on one board inside the body.
Core UV flatbed main board functions
| Function | What it does | Typical symptom when it fails |
|---|---|---|
| Communication | Receives jobs from the RIP over USB or Ethernet | Printer not found, job stops mid-print |
| Data buffering | Stores print data in memory until the carriage needs it | Banding at regular points, garbled output |
| Encoder synchronisation | Uses the encoder strip to fire heads at exact positions | Blurred or doubled images, bidirectional misalignment |
| Motion control | Sends step and direction signals to X, Y and Z drivers | No movement, jerky movement, wrong distance |
| Sensor input | Reads limit, origin, height, collision and door sensors | Homing failure, false collision alarms |
| Output control | Switches lamps, vacuum, ink pumps, circulation and heaters | Lamps or vacuum not switching on |
| Head data distribution | Sends data and clock to carriage or head boards | One or all heads not printing |
| Parameter storage | Holds machine settings, licence and calibration values | Settings lost, licence or dongle errors |
Communication and data handling
The RIP software (for example Ultraprint, Maintop, PhotoPrint or a BYHX print manager) converts your design into dots for each colour and channel. The print control software then sends that data to the main board. On USB machines the board appears as a device on the PC; on network versions it has an IP address. The board buffers incoming data so that a brief pause on the PC does not interrupt printing, then releases it pass by pass.
Encoder and timing
The encoder strip along the gantry tells the board exactly where the carriage is. The board uses this position to time each firing pulse so that dots land in the right place in both directions. A dirty strip or damaged encoder sensor looks like a board fault, but the fix is a clean or a cheap sensor.
Motion and sensors
On a flatbed, the Y-axis moves either the gantry or the table, and the Z-axis lifts the carriage for thick objects. The main board drives all three through stepper or servo drivers and watches the sensors that keep the machine safe: origin and limit switches, the height sensor that measures media thickness, and anti-collision sensors that stop the carriage if something stands too high.
UV flatbed main board ports explained
Port labels vary, but most boards carry the same groups. Photograph your own board and label each cable before you ever remove one.
| Port | Connects to | Check when |
|---|---|---|
| Power input | 24 V or 5 V supplies (often Meanwell SMPS) | Board dead, LEDs off or dim |
| USB / Ethernet | RIP PC | Printer not detected, dropped jobs |
| Data cable to carriage | Carriage or head boards | Heads not printing, carriage communication error |
| X / Y / Z motor driver | Motor drivers | Axis will not move |
| Encoder | Encoder sensor on carriage | Blurred images, encoder error |
| Limit and origin sensors | Switches on each axis | Homing errors |
| Height and collision sensors | Carriage sensors | False collision alarms, auto height wrong |
| Lamp control | UV LED lamp drivers | Lamps not switching or wrong intensity |
| Vacuum and pump outputs | Vacuum relays, ink pumps, white circulation | No suction, no ink feed |
| Ink level and float sensors | Sub-tanks | Low-ink alarms, overfilling |
| Emergency stop and door interlocks | Safety circuit | Machine refuses to move |
| Dongle or licence port | USB dongle or onboard chip | Licence or encryption error |
Power input
The main board usually takes 24 V for outputs and 5 V or 3.3 V for logic, either from separate supplies or from onboard regulators. A failing supply causes random resets, communication drops and sensor errors that look exactly like a dying board. Always measure supply voltages under load before blaming the board. A replacement Meanwell 24 V SMPS costs roughly ₹1,000–3,500 in India depending on wattage, far less than any board.
USB and Ethernet
Older and A3 boards use USB 2.0. Larger Hoson and BYHX systems increasingly use gigabit Ethernet, which is more tolerant of long cable runs and electrical noise. Use short, shielded USB cables with ferrite cores, or good Cat6 network cable on network versions. Our UV flatbed connection problems guide covers this in detail.
Data cable to the carriage
This is the most heavily stressed connection on the machine because it flexes in the cable chain with every pass. Broken strands cause intermittent head errors, garbled prints and communication alarms. On machines with network carriage links, check the cable and connectors at both ends.
Lamp, vacuum and pump outputs
The main board does not usually power these devices directly. It switches relays or sends control signals to lamp drivers and pump drivers. If a lamp will not light, check the lamp driver, its supply and the lamp itself before suspecting the board output. See our UV curing problems guide.
Board indicator LEDs
Most main boards have status LEDs: power, a heartbeat or run LED that blinks when firmware is running, and communication LEDs that flicker during data transfer. Learn what normal looks like on your machine and record it with a short phone video. When a fault appears, compare. A steady power LED with no heartbeat suggests firmware or processor trouble; no power LED points to supply or fuse; a heartbeat with no communication activity points to cable, PC or settings.
Main board vs carriage and head boards
A simple rule helps: the main board handles “where and when”, the carriage and head boards handle “how hard and which nozzle”. If the carriage will not move, the machine will not home or the PC cannot see the printer, look first at the main board side. If one colour or one head misbehaves while everything else is normal, look at the carriage side first. Our UV flatbed carriage board guide and head driver board guide cover that side.
Flatbed-specific functions on the main board
Z-axis and height measurement
Flatbeds print on objects from thin film to 100 mm or thicker. The main board raises and lowers the carriage, reads the height sensor and stores the print gap. A miscalibrated height sensor causes head strikes or poor quality, so always recalibrate after replacing the board or the sensor.
Vacuum zones
Many flatbeds have several vacuum zones switched by the board through relays or valves. If one zone fails while others work, suspect the valve, relay or wiring before the board.
Anti-collision
Collision sensors on the carriage stop movement if they touch an object. The main board must respond instantly. A board that ignores collision inputs is dangerous for heads; test the sensor regularly.
Rotary attachments
Machines that print bottles and cylinders use a rotary device that replaces Y-axis motion. The main board switches between table and rotary modes, and wrong settings here produce stretched or squashed prints.
Using UV flatbed main board functions for fault finding
- Observe the LEDs and compare with your reference video.
- Measure supply voltages at the board connector, not only at the power supply.
- Check communication: does the PC see the printer? Try another USB port, cable or network switch.
- Test each axis from the control software. If one axis fails, swap driver signal cables where the system allows.
- Test sensors: trigger each limit and collision sensor by hand and watch the software status.
- Isolate outputs: if a lamp or pump fails, check the relay and device before the board.
- Only then suspect the board, ideally confirming with a known-good spare or a technician’s test board.
This order prevents the most common mistake: buying a main board for a fault that a ₹500 sensor or a ₹1,500 power supply would fix. For a full list of failure signs, see our UV flatbed main board failure symptoms guide.
Protecting the main board
- Use a servo stabiliser, online UPS and proper earth. See our UV flatbed stabilizer, UPS and earthing guide.
- Fit a surge protection device in the supply to the machine, especially in monsoon areas.
- Keep the electrical cabinet closed, dust-free and ventilated, with working fans.
- Route data cables away from motor and lamp power cables.
- Power off before connecting or disconnecting any cable.
- Back up machine parameters and licence details after any change.
Recording your board details
Create a single page for each flatbed with the board system and model, version number printed on the board, firmware version, software version, IP address or USB settings, licence or dongle serial number, and photos of all ports with cables labelled. Keep a copy on paper near the machine and a digital copy off the PC. When you need a replacement or a technician’s help, this page saves hours and prevents ordering the wrong board.
Board systems at a glance
| System | Common on | Main board notes |
|---|---|---|
| Hoson | A3–2513 i3200 and XP600 flatbeds | USB or network versions, Ultraprint or Maintop software |
| Senyang | A3–A1 XP600 and i3200 flatbeds | Compact boards, good availability |
| BYHX | 2513 and 3020 Ricoh and Konica flatbeds | Separate motion and head boards, network links |
| Machine-maker custom | Branded industrial flatbeds | Usually only available from the maker |
For a deeper comparison of the two most common systems on larger machines, see BYHX vs Hoson UV flatbed main boards.
Bottom line
The main board is the traffic controller of a UV flatbed. It talks to the PC, moves the gantry and carriage, reads every sensor, switches lamps and vacuum, and feeds the heads with data at exactly the right moment. Understanding UV flatbed main board functions and ports turns vague faults into a short list of checks, and in most workshops those checks find a cable, a sensor or a power supply long before the board itself is to blame.
Further reading: The carriage position comes from a linear version of an encoder, read by a small optical sensor on the carriage.
Key takeaways
- The main board handles communication, buffering, encoder timing, motion, sensors and outputs.
- Each function has a port; label and photograph all of them.
- Power supplies, cables and sensors cause many “main board” faults.
- Status LEDs give quick clues if you know what normal looks like.
- Flatbed extras include Z-axis, height sensing, vacuum zones, collision and rotary.
- Protect the board with stable power, surge protection, a clean cabinet and good cable routing.
More in the UV flatbed main board series
- UV Flatbed Main Board Failure Symptoms
- BYHX vs Hoson UV Flatbed Main Boards
- UV Flatbed Firmware Update Guide
- UV Flatbed Head Upgrade: XP600, i3200, Ricoh
- UV Flatbed Connection Problems
- UV Flatbed Main Board Replacement
- UV Flatbed Surge and Lightning Protection
- UV Flatbed Main Board Price in India
- Used UV Flatbed Electronics Check
Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.
Running a UV roll to roll machine as well? The matching guide in our roll to roll series is UV Roll to Roll Main Board: Functions and Ports.
Frequently Asked Questions
What are the main UV flatbed main board functions?
Communication with the RIP PC, data buffering, encoder timing, motion control for X, Y and Z axes, reading sensors, switching lamps, vacuum and pumps, and sending data to the carriage or head boards.
Where is the main board on a UV flatbed?
Usually in the electrical cabinet at one end of the gantry or under the table, near the power supplies and motor drivers, connected to the carriage by a long data cable.
Does the main board fire the heads?
Not directly. It sends data and timing to the carriage, head or driver boards, which generate the firing pulses.
Why does my PC not detect the printer?
Check the USB or network cable, PC port, drivers, IP settings and main board power before suspecting the board.
What voltage does the main board use?
Most use 24 V for outputs and 5 V or 3.3 V for logic, supplied by SMPS units or onboard regulators. Check your board’s manual.
Can a bad power supply look like a main board fault?
Yes. Low or unstable supply voltage causes resets, communication errors and sensor faults that mimic a failing board.
What does the encoder port do?
It reads the encoder sensor so the board knows the carriage position and can time each firing pulse accurately.
Why does my carriage refuse to home?
Common causes are a faulty origin or limit sensor, broken sensor cable, motor driver fault or a blocked axis, not necessarily the main board.
How do collision sensors connect?
They connect to sensor inputs on the main board or carriage board, which stop motion when the sensor is triggered.
Does the main board control UV lamps?
It switches them on and off and may set intensity, but the lamp driver and lamp supply do the actual powering.
What do the main board LEDs mean?
Typically power, heartbeat or run, and communication activity. Compare with a recording of normal behaviour on your machine.
Is USB or network better on a UV flatbed?
Network versions handle longer distances and electrical noise better, which suits larger flatbeds. USB is fine for A3 and A2 machines with short shielded cables.
Where are licence details stored?
On a USB dongle, an onboard chip or in the control software tied to the board. Record serial numbers before any replacement.
How do I protect the main board?
Use stable power, surge protection, good earthing, a clean ventilated cabinet and always power off before touching cables.
Should I photograph the board ports?
Yes. Photos with labelled cables make replacement, repair and troubleshooting much faster and safer.
Are Hoson and BYHX main boards interchangeable?
No. Each system needs its own carriage boards, firmware and software. Changing system means changing the full board set.