Direct answer: The UV flatbed head driver board is the circuit that turns print data into the high-voltage firing pulses that make each piezo nozzle eject a droplet of UV ink. On A3, A2 and 6090 flatbeds with Epson XP600, TX800 or i3200-U1 heads, the driver circuit is usually built into the Hoson or Senyang head board on the carriage. On 2513 and 3020 flatbeds with Ricoh Gen5, Gen5i or Gen6 heads, it may be a separate driver or head-group board fed by a BYHX or Hoson carriage board. The driver board generates the waveform, applies the head voltage you set in software, and protects the head with overcurrent detection. Because a damaged driver channel can destroy a new head in seconds, understanding this board is essential before any head replacement.
Understanding the UV flatbed head driver board is essential before any head replacement, because a damaged driver channel can destroy a new head within seconds.

Table of Contents
This article opens Section B of our UV flatbed electronics series. Section A covered the UV flatbed carriage board; here we look at the part of the electronics that actually fires the nozzles, and at the power and cooling that keep it alive.
What a piezo head needs from its driver
Epson, Ricoh and Konica heads used on UV flatbeds are piezoelectric. Each nozzle has a tiny piezo element that flexes when voltage is applied, pushing a droplet out. To work, every nozzle needs:
- A firing waveform: a precisely shaped voltage pulse that controls drop size and speed.
- The right voltage: each head has its own recommended drive voltage, printed on its label for Epson heads.
- Timing: fire commands synchronised with the encoder so drops land in the right place.
- Nozzle selection data: which nozzles fire on each pulse.
- Protection: current limiting so a short does not burn the head or board.
The UV flatbed head driver board supplies all of these. It is the most electrically stressed part of the carriage electronics.
Where the driver lives on different flatbeds
| Flatbed type | Typical heads | Driver location |
|---|---|---|
| A3 desktop | 1–2 × XP600 or i3200-U1 | Integrated in Hoson/Senyang head board |
| A2 / 6090 | 2–4 × i3200-U1 | Integrated head board, sometimes split per head pair |
| 1313 / 1610 | 3–4 × i3200-U1 or Ricoh | Head board or separate driver boards |
| 2513 | 4–8 × Ricoh Gen5/Gen6 | Head-group or driver boards on the carriage |
| 3020 and larger | 8+ × Ricoh, Konica or Kyocera | Multiple driver boards, often per colour group |
On Epson-head machines, people often say “head board” when they mean the integrated driver. On Ricoh machines, the terms “driver board”, “head board” and “transfer board” are used loosely. Our guide to driver board vs main board vs head board untangles the names.
Inside a UV flatbed head driver board
| Section | Job | Typical failure |
|---|---|---|
| Power input and regulators | Convert supply voltages to logic and drive rails | Burnt regulators after surges or shorts |
| Waveform generator | Shape the firing pulse | Wrong drop size, weak jetting |
| Driver amplifiers / transistors | Deliver high current pulses to the head | Overheating, burnt channels |
| Logic and FPGA | Handle data and timing | Garbled printing, communication errors |
| Protection circuits | Detect overcurrent and over-temperature | False alarms or failure to protect |
| Connectors | Link to heads, adapters and carriage board | Ink corrosion, angled insertion damage |
Head voltage and why it matters
The drive voltage controls how hard each piezo element pushes. Too low and drops are small or missing; too high and the head is overdriven, shortening its life and causing satellites and mist. Epson i3200-U1 and XP600 heads carry a recommended voltage on their label. Ricoh heads use voltage or waveform settings provided by the board maker. Always enter the value for the specific head in its own channel, never copy one head’s setting to another. See our detailed guide on i3200-U1 head voltage on UV flatbeds.
Why driver channels fail on UV flatbeds
Heat
Driver transistors convert some of their power into heat. On a flatbed carriage they sit next to UV LED lamps, so cooling margins are small. Weak fans or a struggling chiller push driver temperatures up, and repeated heat cycling ages components.
Shorted heads
A head damaged by a crash, by ink inside its connector or by age can draw excessive current. The driver channel tries to deliver it and burns. This is why a failed head must never be replaced before the channel is checked.
Hot-plugging and angled cables
Connecting a head with power on, or inserting a ribbon cable one pin off, sends drive voltage where it should not go.
Power disturbances
Voltage dips, spikes and poor earthing stress regulators and drivers. Workshops on shared industrial lines or with frequent generator changeovers see more failures. See our guide to UV flatbed stabiliser, UPS and earthing.
Ink and static
UV ink mist cured on the board, and static discharges from acrylic sheets, add to the stress.
Symptoms of driver problems
- Overcurrent or head short alarms.
- One head printing faintly or with small drops while others are normal.
- A new head failing within hours or days.
- Heads that work cold but fail warm.
- Burn marks or discoloration near driver components.
Our article on UV flatbed driver board failure signs covers diagnosis in depth.
Epson-head flatbeds: integrated drivers
On Hoson and Senyang i3200 kits, the driver for each head is part of the head board. A burnt channel usually means repairing or replacing the whole head board. Late 2026 listings showed Hoson i3200 head boards for one, two or four heads at about $388–450, with a four-head V1.24 board at about $411 and original four-head boards at about $570–620, before shipping and duty. Because i3200-U1 heads cost about ₹78,000–95,000 each in India, protecting the driver is protecting the head.
Ricoh-head flatbeds: separate drivers
Many 2513 machines use separate driver or head-group boards, each serving two or four Ricoh heads. A failure may take out only that group. Ricoh Gen5 heads cost about ₹1.25–1.55 lakh each and Gen6 around ₹1.7 lakh, so testing the driver group before fitting new heads is essential. See Ricoh Gen6 printhead price in India.
Protecting the UV flatbed head driver board
- Switch off and isolate power before touching any head cable.
- Keep carriage and lamp cooling healthy; clean fans weekly.
- Use a stabiliser, online UPS and proper earth.
- Enter correct voltages from head labels.
- Investigate every overcurrent alarm before continuing.
- Clean ink mist from boards with power off.
- Control static from acrylic and PVC sheets.
- Test channels before fitting new heads after any failure.
Example: faint magenta on an A2 flatbed
A Lucknow gift printer saw magenta becoming faint over a week. Cleaning did not help. The head voltage setting had been accidentally changed during a software update. Restoring the label value fixed the problem immediately, and no board was needed.
Example: repeated head failures on a 2513
A signage unit in Kanpur lost two new Ricoh heads in the same position within a month. Testing showed a damaged driver group board delivering abnormal pulses. Replacing the driver board stopped the failures. Testing it before the first replacement would have saved one head.
How the UV flatbed head driver board shapes a drop
Each firing pulse is not a simple on-off signal. A typical piezo waveform has several stages: a pull phase that draws ink into the chamber, a push phase that ejects the drop, and a damping phase that settles the meniscus before the next pulse. Grey-scale heads such as the i3200-U1 and Ricoh Gen5 use multiple pulses per dot to create small, medium and large drops. The driver board must reproduce these stages precisely, thousands of times per second, for every nozzle. If any stage is distorted, for example by a weak driver transistor or a sagging supply rail, drops become uneven, satellites appear, and fine text loses sharpness.
| Waveform stage | Purpose | Symptom if distorted |
|---|---|---|
| Fill (pull) | Draws ink into the chamber | Missing drops at high frequency |
| Fire (push) | Ejects the drop | Small, slow or deflected drops |
| Damp | Settles meniscus | Satellites, mist, unstable jetting |
| Grey-level pulses | Create variable drop sizes | Grainy gradients, banding |
Supply rails and why they matter
The driver board needs stable supply voltages. A typical flatbed carriage receives a logic supply and a higher drive supply from power supplies in the cabinet or on the carriage. If the drive supply sags under heavy load, for example when all heads fire solid white and varnish, the waveform peak drops and heads print faintly. If it spikes, drivers are stressed. Loose power terminals, undersized cables to the carriage and ageing power supplies all cause rail problems. Technicians can measure rails at test points while printing a solid fill to check stability.
| Rail problem | Typical cause | Effect |
|---|---|---|
| Sagging under load | Ageing power supply, undersized cable | Faint solids, resets |
| Noise on rail | Poor earth, failing capacitors | Random nozzle dropout |
| Intermittent loss | Loose terminal, cracked cable | Heads disappear and return |
| Overvoltage spike | Surge, generator changeover | Burnt regulators or drivers |
Temperature limits for driver components
Driver transistors and regulators are designed to run warm, but each has a maximum safe temperature. On a flatbed carriage, ambient air inside the cover can be well above room temperature because of lamp heat. Every few degrees of extra heat shortens component life. Practical steps include keeping carriage fans clean, making sure covers have their intended ventilation openings, keeping lamp cooling efficient, and avoiding blocking air paths with cable bundles or tape. Some boards have heat sinks on driver sections; check these are clean and firmly attached.
Driver protection features and their limits
Most modern boards include overcurrent detection that shuts a channel down if a head draws too much current. This protection saves many heads and boards, but it is not perfect. A fast short can damage components before protection reacts, and a head with a partial fault may draw slightly elevated current for a long time without triggering an alarm, slowly heating the driver. Treat protection as a last line of defence, not a reason to skip careful handling. If alarms are disabled or ignored, the board and head lose that safety net.
Spare strategy for driver boards
On Epson-head flatbeds, a spare head board is effectively a spare driver. For shops running one machine on tight deadlines, a tested spare head board of the matching version can cut downtime from weeks to hours. On Ricoh flatbeds with separate driver group boards, one spare driver board can often cover several positions. Store spares in anti-static bags with a label showing model, version and test date. See our UV flatbed electronics spares stock list for other items worth keeping.
Questions to ask your supplier about the driver
- Is the driver integrated into the head board on my machine or separate?
- Which waveform file is correct for my heads and ink?
- What head voltage range is safe for my head type?
- Can you test a channel before I fit a new head?
- Do you stock spare head or driver boards of my version?
- What warranty applies to driver boards?
Quick reference: driver health signs
A healthy driver section runs warm but not hot, produces consistent nozzle checks at label voltage, and never raises unexplained overcurrent alarms. If any of these change, investigate before the next long job.
Bottom line
The UV flatbed head driver board turns data into the firing pulses that make piezo heads work. It is integrated into the head board on most Epson-head flatbeds and separate on many Ricoh machines. Heat, shorted heads, hot-plugging, power problems and ink damage cause most failures. Protect it with cooling, clean power, careful handling and correct voltages, and always test the channel before fitting a new head.
Further reading: Each nozzle is fired by piezoelectricity: the element flexes when the driver applies voltage.
Key takeaways
- The driver generates waveforms, applies head voltage and protects against overcurrent.
- Epson-head flatbeds usually integrate the driver into the head board; Ricoh flatbeds often use separate driver boards.
- Heat, shorted heads, hot-plugging and power problems cause most failures.
- Correct head voltage from the label is essential.
- Test the driver channel before fitting a new head.
More in the UV flatbed head driver board series
- Driver Board vs Main Board vs Head Board
- UV Flatbed Driver Board Failure Signs
- Why a New UV Flatbed Head Fails Fast
- Epson i3200-U1 Head Voltage on UV Flatbeds
- UV Flatbed Board Compatibility
- UV Flatbed Board Repair vs Replacement
- UV Flatbed Stabilizer, UPS and Earthing
- UV Flatbed Lamp Cooling and Board Overheating
Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.
Running a UV roll to roll machine as well? The matching guide in our roll to roll series is UV Roll to Roll Head Driver Board Explained.
Frequently Asked Questions
What is a UV flatbed head driver board?
It is the circuit that converts print data into firing pulses for the piezo heads, applies head voltage and protects against overcurrent.
Is the driver board separate from the head board?
On most Epson-head flatbeds the driver is built into the head board. On many Ricoh flatbeds it is a separate board.
Why do driver channels burn?
Heat, shorted heads, hot-plugging, angled cables, power disturbances, ink and static.
Can a bad driver damage a new head?
Yes. Always test the channel before fitting a new head after a failure.
What does head voltage do?
It controls how hard each piezo element pushes ink, affecting drop size and head life.
Where do I find the correct head voltage?
On the head’s label for Epson heads, or from the board maker for Ricoh heads.
How much does a Hoson i3200 head board cost?
Late 2026 listings showed about $388–450 for 1–4 head versions, and about $570–620 for original four-head boards.
What are signs of driver trouble?
Overcurrent alarms, faint heads, new heads failing quickly, warm-up faults and burn marks.
Does lamp heat affect the driver?
Yes. Drivers sit near UV lamps, so weak cooling raises their temperature.
Do power problems damage drivers?
Yes. Surges, dips and poor earthing stress regulators and driver components.
How much do Ricoh Gen5 heads cost?
About ₹1.25–1.55 lakh each in India in 2026.
Should I investigate every overcurrent alarm?
Yes. Continuing to print can burn the head and driver.
Can I copy voltage from one head to another?
No. Each head has its own recommended value.
Can Unified Engineering Dynamics supply driver and head boards?
Yes. Send photos and machine details and our team will help identify compatible boards.
What is a firing waveform?
A shaped voltage pulse with fill, fire and damping stages that controls drop size and stability.
Can a weak power supply cause faint printing?
Yes. A sagging drive supply lowers the waveform peak, especially on heavy solids.
Does overcurrent protection always save the head?
No. Fast shorts or slow partial faults can still cause damage, so careful handling remains essential.
Should I keep a spare driver or head board?
Busy single-machine shops often keep a tested spare of the matching version to avoid long downtime.