Direct answer: The UV flatbed carriage board, also called the head board, is the circuit board mounted on the moving print carriage of a UV flatbed printer. It receives print data from the main board, splits it into separate streams for each printhead and colour channel, controls head heating and, on many machines, reads the head height and anti-collision sensors. On A3 and A2 flatbeds it usually drives one to three Epson XP600, TX800 or i3200-U1 heads on a Hoson or Senyang board; on 2513 and 3020 industrial flatbeds it drives four to eight Ricoh Gen5, Gen5i or Gen6 heads on BYHX or Hoson boards. Because it sits beside the UV LED lamps, above reflective substrates and in a cloud of ink mist, it is the board most likely to fail on a flatbed. Most failures come from heat, ink contamination, static from acrylic sheets, head crashes and careless head changes.
If you run an acrylic, glass or gift-printing machine, understanding the UV flatbed carriage board is the fastest way to cut downtime and avoid buying the wrong parts.

Table of Contents
This article opens our 35-part series on UV flatbed printer electronics. If you run a UV flatbed for acrylic signage, glass printing, MDF and wood decor, phone covers, trophies or promotional items, understanding the carriage board will help you diagnose faults faster, protect expensive heads and avoid buying the wrong replacement.
Where the carriage board sits on a UV flatbed
On a UV flatbed, the carriage rides along an X-axis beam mounted on a gantry. On smaller machines the table moves under a fixed gantry; on larger 2513 and 3020 machines the gantry travels along the Y-axis over a fixed vacuum table. In both cases the carriage holds the printheads, their dampers and ink lines, the UV LED lamps on one or both sides, and the carriage board, usually under a metal cover just above the heads. A flat data cable or, on larger machines, a fibre link runs through the cable chain from the main board in the electronics cabinet to the carriage board.
Because the carriage must also move up and down to clear substrates of different thickness, many flatbeds add a Z-axis motor, a height sensor and an anti-collision switch, and these sensors often connect to the carriage board as well. This makes the flatbed carriage board busier than its roll to roll equivalent.
What the carriage board does
| Function | What it means in practice |
|---|---|
| Data distribution | Receives image data from the main board and sends the right dots to each head and nozzle row |
| Head interface | Connects to each head through data cables and, often, small adapter boards |
| Driver section | On many i3200 and Ricoh kits, contains or feeds the driver circuits that generate the firing waveform |
| Head heating | Controls head heaters and reads thermistors so UV ink stays at the right viscosity |
| Sensors | Reads head height, anti-collision, and sometimes lamp and temperature sensors |
| Status reporting | Reports errors such as head not found, overcurrent and over-temperature back to the main board |
Small flatbeds vs industrial flatbeds
| Feature | A3/A2 and 6090 flatbeds | 2513 and 3020 flatbeds |
|---|---|---|
| Typical heads | Epson XP600, TX800, i3200-U1 (1–3 heads) | Ricoh Gen5, Gen5i, Gen6, sometimes Konica 1024i or Kyocera (4–8 heads) |
| Common board systems | Hoson, Senyang | BYHX, Hoson, sometimes maker’s own |
| Data link | Flat cable, sometimes network port | Flat cable bundle or fibre |
| Lamp cooling | Often air-cooled LED lamps with fans | Usually water-cooled LED lamps with a chiller |
| White and varnish | CMYK+W common, varnish on 3-head machines | CMYK+W+V common |
| Typical failure triggers | Head changes, static, ink leaks, lamp heat | Heat, ink mist, cable wear, power, crashes |
For an overview of head choices, see our comparison of Epson i3200 vs XP600 and Ricoh Gen5 vs Gen5i.
How the carriage board works with other boards
The UV flatbed carriage board is one part of a chain. The main board in the cabinet talks to the RIP PC, controls the X, Y and Z motors, reads the encoder and vacuum controls and switches the lamps. It streams print data to the carriage board in step with the encoder position. The carriage board distributes data to the heads, and the driver section fires each nozzle. Adapter boards above the heads connect the head ribbon cables. If any link fails, the symptom often looks like a carriage board fault even when it is not. Our article on driver board vs main board vs head board explains each role.
Why UV flatbed carriage boards fail
1. Lamp heat and UV exposure
UV LED lamps sit within centimetres of the carriage board. On air-cooled A3 machines, a slow fan quickly raises carriage temperatures; on water-cooled machines, a weak chiller does the same. Heat ages capacitors and driver components. Stray UV light can also cure ink mist on board surfaces, building a hard, conductive crust.
2. Ink mist and leaks
Each pass throws a fine mist of UV ink. Over weeks it settles on boards and connectors. A leaking damper or loose ink line can drip ink directly onto the board, causing shorts and corrosion. White ink, with its heavy pigment, is particularly troublesome.
3. Static from rigid substrates
Acrylic sheets, PVC foam board and polycarbonate generate strong static, especially when the protective film is peeled just before printing. Static discharges can jump to the carriage, upsetting data or damaging head and board circuits. Good earthing and anti-static measures are essential on flatbeds.
4. Head crashes
Warped boards, raised edges and incorrect height settings can make heads strike the substrate. A crash can damage nozzle plates, tear cables, crack adapter boards and short a head into the carriage board. See our guide to head crashes, UV reflection and board damage.
5. Careless head changes
Connecting or disconnecting heads with power on, inserting ribbon cables at an angle, or fitting a shorted head are the commonest causes of burnt head boards. See burnt head boards after an i3200 head change.
6. Cable wear
The cable chain flexes thousands of times a day. Flat cables crack, connectors loosen, and intermittent data errors appear long before total failure.
7. Power problems
Voltage fluctuations, surges and poor earthing damage power supplies and the boards they feed. See our UV flatbed power protection guide.
Common symptoms of carriage board trouble
- One head or one colour missing even after cleaning.
- “Head not found”, “head board error” or communication errors.
- Heads failing to warm up or showing wrong temperatures.
- Random missing lines or garbled printing.
- Faults that appear when the carriage is warm.
- Height sensor or anti-collision errors without a real obstruction.
- Burnt smell, visible burn marks or swollen components.
Many of these can also come from heads, cables or the main board. Our guide to UV flatbed head board failure symptoms shows how to tell the difference.
How to protect the carriage board
- Power off for every connection. Never plug or unplug head cables with power on.
- Keep cooling healthy. Clean lamp and carriage fans weekly; service the chiller on water-cooled machines.
- Control ink mist. Clean covers and boards with an anti-static brush; fix leaks immediately.
- Manage static. Earth the machine and table, use anti-static measures when peeling films, maintain moderate humidity.
- Set head height correctly. Measure substrate thickness, check for warping, and keep anti-collision sensors working.
- Inspect cables. Check the cable chain monthly and replace worn cables.
- Protect power. Use a stabiliser, UPS, surge protection and a dedicated earth.
- Keep records. Photograph boards and cables, note versions and head settings.
Identifying your carriage board
Before buying any replacement, identify the board precisely. Photograph both sides and note the brand (Hoson, Senyang, BYHX), the board model or part number, version stickers, the number of head connectors and the head type. Record the main board model and software version too, because carriage boards must match the main board system and version. Our article on Hoson vs Senyang vs BYHX UV flatbed boards helps you recognise each system.
Repair or replace?
Limited damage, such as a burnt connector or a failed regulator, can often be repaired by a specialist with proper testing. Extensive burns, ink corrosion across the board or repeated failures usually justify replacement. Always fix the root cause first, whether that is a shorted head, a leaking damper or poor earthing. See UV flatbed board repair vs replacement.
Example: A3 flatbed in Lucknow
A gift-printing shop running an A3 flatbed with two i3200-U1 heads lost the white head after an operator reseated its cable with the machine switched on. The adapter and the head channel on the carriage board burnt. Replacing the board and adapter cost far more than the few seconds saved.
Carriage board inputs and outputs at a glance
When a technician opens the carriage cover, the number of plugs can look confusing. Grouping them by job makes diagnosis much faster. The table below lists what you will typically find on a Hoson or Senyang i3200 flatbed carriage board, and on a BYHX or Hoson Ricoh board on a larger machine.
| Connector group | Connects to | Fault if disturbed |
|---|---|---|
| Main data input | Flat cable or fibre from the main board | All heads stop, communication errors |
| Power input | Carriage power supply or rail from the cabinet | Board dead, resets, heads not found |
| Head data outputs | One or two ribbon cables per head or adapter | One head or colour missing |
| Heater and thermistor | Head heaters, damper heaters on some machines | Temperature errors, poor jetting of white |
| Height sensor | Optical or mechanical sensor on carriage | Height measurement fails, wrong head gap |
| Anti-collision switch | Bar or micro-switch beside heads | False collision errors or no protection |
| Lamp signals (some kits) | Lamp driver or lamp enable lines | Lamps not switching with print direction |
| Fan outputs (some kits) | Carriage cooling fans | Carriage overheating |
Label every plug before removal and keep a photo set of your own machine.
How the carriage board keeps heads in step with the table
On a flatbed, every droplet must land at the right position on a rigid sheet that cannot be adjusted after printing. The main board reads the linear encoder strip along the X-axis beam and the Y-axis position from the table or gantry motor. It sends firing timing to the carriage board, which triggers each head in sequence. If the encoder signal is dirty or the data link is noisy, the carriage board fires at the wrong moment, producing banding, doubled edges or misregistered white under colour. That is why a “carriage board fault” is sometimes cured by cleaning the encoder strip. Our article on carriage belts, rails, encoder and sensor service covers encoder cleaning step by step.
On gantry-type 2513 machines, two Y-axis motors drive each side of the gantry. If they fall out of sync, the gantry skews slightly and the heads print at an angle to the sheet. The symptom looks like a print fault, but the cause is mechanical or motor-driver related, not the carriage board.
Carriage board health checks you can do weekly
| Check | How | What good looks like |
|---|---|---|
| Cover cleanliness | Look under the carriage cover with power off | No wet ink, no cured crust on components |
| Fan operation | Watch carriage and lamp fans at start-up | All fans spinning freely, no rattling |
| Head temperatures | Compare readings in the software | All heads within a degree or two of the set value |
| Cable locks | Visual check with torch | All locks closed, cables straight |
| Collision switch | Trigger gently with carriage stopped | Software shows the alarm immediately |
| Nozzle check | Print at start of shift | All heads and rows complete |
These checks take ten minutes and catch most developing faults early, long before a board burns.
Why the UV flatbed carriage board deserves a spare
For shops running a single flatbed on deadline-driven work such as wedding gifts, corporate awards or retail signage, a dead carriage board can stop all income for days while a part is imported. Many busy shops in India now keep a tested spare carriage board of the matching version, stored in an anti-static bag with a note of its version and test date. The cost is often recovered by avoiding a single week of downtime. At minimum, keep spare head cables and adapters, which fail far more often than boards. Our guide to UV flatbed electronics spares suggests a sensible stock list.
Bottom line
The UV flatbed carriage board is the hub of everything on the carriage: data, head heating, sensors and status. It works in the harshest environment on the machine, beside hot lamps, above reflective and static-prone substrates and in constant ink mist. Protect it with good cooling, cleaning, static control, correct head height, careful head changes and clean power, and identify it precisely before buying any replacement.
Further reading: For background on the curing process that makes these machines work, see this overview of ultraviolet curing.
Key takeaways
- The carriage board distributes data, controls head heating and often reads height and collision sensors.
- Small flatbeds use Hoson or Senyang boards with Epson heads; industrial flatbeds use BYHX or Hoson with Ricoh heads.
- Heat, ink mist, static, crashes, head changes, cable wear and power cause most failures.
- Always switch off before touching head cables.
- Identify system, version and head type before buying a replacement.
More in the UV flatbed carriage board series
- UV Flatbed Head Board Failure Symptoms
- Hoson vs Senyang vs BYHX UV Flatbed Boards
- Adding White and Varnish Heads to a UV Flatbed
- Head Crashes, UV Reflection and Board Damage
- UV Flatbed Head Cable vs Carriage Board Fault
- UV Flatbed Carriage Board Replacement Checklist
- Burnt Head Board After an i3200 Head Change
- UV Flatbed Carriage Board Price in India
- UV Flatbed Board Connectors and Static
Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.
Running a UV roll to roll machine as well? The matching guide in our roll to roll series is UV Roll to Roll Head Carriage Board Explained.
Frequently Asked Questions
What is a UV flatbed carriage board?
It is the board on the print carriage that receives data from the main board, distributes it to each head, controls head heating and often reads height and collision sensors.
Is the carriage board the same as the head board?
The terms are often used interchangeably. Some machines also have small adapter boards above each head and a separate driver board.
Which heads do UV flatbed carriage boards support?
Small flatbeds commonly use Epson XP600, TX800 or i3200-U1 heads; industrial flatbeds use Ricoh Gen5, Gen5i or Gen6, sometimes Konica or Kyocera.
Why do UV flatbed carriage boards fail?
Lamp heat, ink mist and leaks, static from acrylic and PVC sheets, head crashes, careless head changes, cable wear and power problems.
Can static from acrylic sheets damage the board?
Yes. Peeling protective film creates strong static that can discharge into the carriage. Earthing and anti-static measures help.
How do I know if the carriage board is faulty?
Symptoms include missing heads after cleaning, head not found errors, heating faults and garbled printing. Rule out heads and cables with swap tests first.
Can I plug in a head cable with the power on?
No. Hot-plugging is one of the commonest causes of burnt head boards and heads.
Do I need the same brand of board as my main board?
Yes. Carriage and main boards must come from the same system, such as Hoson, Senyang or BYHX, with compatible versions.
How much does a UV flatbed carriage board cost?
Late 2026 listings showed a Hoson i3200 double carriage board around $430, full i3200 kits about $600–1,120, and Ricoh Gen5 carriage boards around $287–652.
Can a carriage board be repaired?
Limited damage often can be repaired by a specialist; extensive burns or corrosion usually mean replacement.
Does lamp cooling affect the carriage board?
Yes. Weak fans or chillers raise carriage temperatures and shorten board life.
What records should I keep about my carriage board?
Photos of both sides, brand, part number, version, head connectors, head type, main board model and software version.
Can a head crash damage the carriage board?
Yes. Crashes can tear cables, crack adapters and short heads into the board.
Can Unified Engineering Dynamics help identify my carriage board?
Yes. Send clear photos and your machine details and our team will help identify compatible boards and parts.
Does the carriage board control the UV lamps?
On some kits it carries lamp enable signals, but lamp power usually comes from a separate driver controlled by the main board.
Can a dirty encoder strip look like a carriage board fault?
Yes. Dirty encoders cause misfiring, banding and misregistration that can be mistaken for board faults.
Should I keep a spare carriage board?
Busy shops with one machine often keep a tested spare of the matching version to avoid long downtime.