Eco Solvent Printing

Single-Head vs Double-Head Carriage Boards: Upgrading Without Changing the Mainboard

Double Head Carriage Board Upgrade: Complete Guide

Direct answer: Upgrading an eco-solvent printer from one head to two by changing only the carriage board is sometimes possible, but only when the existing mainboard, firmware and software already support two heads and the board maker offers a matching double-head carriage board for that exact kit version. In many entry-level machines the mainboard is built or licensed for a specific head count, so a real single-to-double upgrade also needs a new mainboard or a complete board kit, plus a second head, a dual head plate, extra dampers and ink lines, a wider or modified capping station, more ink supply, new data and head cables, and fresh calibration and colour profiles. Before spending, confirm with the board supplier that your mainboard version supports the upgrade, and compare the total cost with buying a double-head machine.

A double head carriage board is only one part of the upgrade, so this guide covers everything that has to change around it.

Double Head Carriage Board Upgrade: Complete Guide
Double Head Carriage Board Upgrade: Complete Guide

Many shop owners who bought a single-head printer to start their business reach a point where they need more speed. A second head can nearly double production on many jobs, so upgrading is a natural question. This guide explains what is technically involved, which parts must change, and how to decide whether the upgrade is worth it. For the business side of single vs double head machines, see our comparison of single head vs double head eco-solvent printers.

Why a double head carriage board is not the whole upgrade

The carriage board drives the heads, but it is not the only part of the system that “knows” how many heads are installed. In a typical eco-solvent printer:

  • The mainboard manages the data flow from the PC and sends data for each head to the carriage. Its processor, memory and firmware are designed for a certain maximum number of heads and a certain data rate.
  • The carriage board has a fixed number of head channels and connectors. A single-head board physically cannot drive a second head.
  • The firmware and print control software define head arrangement, head spacing, colour channels and printing modes. They must be configured for two heads.
  • The RIP software must have a printer driver or settings that match the new head layout.
  • Licences or authorisation on some board systems are tied to head count, so the same physical board might be unlocked for one head or two.

So when a seller offers a “double-head carriage board” for your machine, the key question is not whether the board exists but whether your current mainboard and firmware will run it.

When a carriage-board-only upgrade can work

A carriage-board-only upgrade (plus heads and mechanical parts) is realistic when:

  1. Your board kit brand offers single-head and double-head carriage boards that use the same mainboard model and version.
  2. Your mainboard version is confirmed by the supplier to support two heads of your chosen type.
  3. The firmware for two-head operation is available for your mainboard version, and the supplier will provide it.
  4. Any authorisation or licence for two-head operation can be enabled for your machine.
  5. The carriage housing has space for the larger board and the second head, or a compatible carriage is available.

Some Hoson and Senyang kit families have been designed this way, with a common mainboard and different carriage boards. Whether your specific machine qualifies depends on the exact versions installed, which is why a photo of the mainboard label and the software version screen is the first thing a supplier will ask for. Our article on Hoson vs Senyang vs BYHX carriage board compatibility explains how versions affect matching.

When you need a new mainboard or full kit

You should plan for a new mainboard or full kit when:

  • The mainboard is a single-head-only model, which is common in budget machines.
  • The board generation is old and no double-head carriage board exists for it.
  • You are changing head type at the same time, for example from one XP600 to two i3200 heads.
  • The machine manufacturer has locked the board configuration and will not unlock two-head operation.
  • The mainboard is the same family but too old to support the data rate needed for two heads in high-speed modes.

In these situations, a complete matched kit (mainboard, carriage board, data cable, adapter boards and software) is usually more reliable than mixing old and new parts.

The full list of parts for a single-to-double head upgrade

The carriage board is only one part of the job. A complete upgrade typically involves the following. Exact parts depend on the machine.

PartWhy it is neededNotes
Double-head carriage boardDrives two headsMust match mainboard brand and version
Mainboard (if not compatible)Supports two-head data and firmwareOften required on budget machines
Second printheadAdditional nozzlesSame type and ink variant as first head, ideally same batch quality
Head plate or head mount for two headsHolds both heads at correct spacing and anglePrecision matters for alignment
Adapter boards and head cablesConnect heads to boardCorrect type and length
Data cableMay need higher capacity or different typeCheck with board supplier
Additional dampers and ink tubesFeed the second headCorrect damper type for head
Capping station for two headsCaps and cleans both headsSingle capping station cannot protect the second head
Wiper and pump capacityCleaning for both headsPump may need upgrade
Ink supply systemMore channels or larger tanksDepends on colour configuration
Carriage cover or housingSpace for larger board and second headSome machines need a different carriage
Power supply checkTwo heads and larger board draw more currentConfirm power supply rating
Software, firmware and RIP settingsTwo-head configuration and print modesNew calibration and colour profiles

The capping station is often forgotten. Without proper capping, the second head dries out and fails quickly. Our guide to capping stations explains why this part is so important.

Two heads: speed or colours?

A second head can be used in different ways, and the configuration affects which carriage board, capping station and ink system you need:

  • Staggered or parallel CMYK + CMYK: both heads print the same four colours, roughly doubling speed in many modes. This is the most common upgrade for production shops.
  • CMYK + light colours or extra colours: the second head adds light cyan, light magenta or other colours for smoother gradients and skin tones. Speed gain is smaller.
  • Colour + white or varnish: mainly used in UV and DTF machines; less common for standard eco-solvent work.

Decide your goal before buying parts. For most Indian eco-solvent shops printing vinyl, stickers, one-way vision and backlit, CMYK + CMYK for speed is usually the right choice.

Realistic speed gain

Two heads do not always mean double speed. Real-world gains depend on print mode, number of passes, media feeding, drying limits and the RIP. In production modes, a well-configured double-head machine can be close to twice as fast. In high-quality modes with many passes, or when drying is the bottleneck, the gain is smaller. Heaters and drying fans may become the new limit, especially with heavy ink coverage. Discuss expected speeds in your most common modes with your supplier before deciding.

Costs and how to compare with a new machine

An upgrade bill typically includes the board or kit, the second head, mechanical and ink system parts, installation labour, and downtime while the machine is converted and calibrated. Board and head prices vary with brand, version and market conditions, so collect current written quotes. When comparing with a new double-head machine, look at:

FactorUpgrade existing machineBuy new double-head machine
Upfront costLower, if the mainboard is compatibleHigher
Mechanical conditionOld rails, belts, motors and heaters remainAll new mechanics
WarrantyOnly on new parts, if anyFull machine warranty
DowntimeMachine out of service during upgradeOld machine keeps working while new one is installed
CapacitySame total machine countTwo machines if you keep the old one
RiskIntegration issues possibleLower, factory-built configuration

If the existing machine is in good mechanical condition and the mainboard supports two heads, an upgrade can be good value. If it needs a full kit, a new carriage, capping station and other major parts, the cost can approach that of a new entry-level double-head machine, and the new machine comes with warranty and better mechanics. Keeping the old single-head machine as a backup or for small jobs is often a smart move. Our article on eco-solvent printer prices in India gives a baseline for comparison.

The upgrade process step by step

The work should be done by a technician experienced with your board system. The general sequence is:

  1. Survey the machine: record board brand, versions, firmware, head type, power supply rating, carriage space and capping station design.
  2. Confirm compatibility in writing: get the supplier to confirm that the mainboard supports the chosen double-head carriage board, or quote a full kit.
  3. Plan mechanics: head plate, capping station, wiper, dampers, tubes and ink supply for two heads.
  4. Back up settings: save existing parameters, calibration values and RIP settings before changing anything.
  5. Install mechanics: fit head plate, capping station, ink lines and dampers, check for leaks.
  6. Install electronics with power off: fit the new carriage board, adapters, head cables and data cable; check routing so cables do not rub or pull.
  7. Update firmware and software: load the correct firmware and configure two-head operation.
  8. Set head voltages: enter the correct voltage values for each head from their labels.
  9. Prime and test: fill ink, run cleanings, print nozzle checks.
  10. Calibrate: head height, head angle, head-to-head alignment, bidirectional alignment and media feed.
  11. Create colour profiles: new ICC profiles for the main media types.
  12. Run production tests: print real jobs in your main modes and check for banding, colour differences between heads and drying.

Head-to-head alignment is critical. If the second head is not precisely aligned, you will see banding or a visible joint between the areas printed by each head. A good head plate and careful calibration are essential. For more on what installation should include, see our printing machine installation checklist.

Risks to manage

  • Version mismatch: a carriage board that does not match the mainboard can fail to work or behave unpredictably.
  • Power supply overload: an undersized power supply may cause random errors or failure. Confirm the rating.
  • Head damage during installation: wrong cable insertion or wrong voltage can damage new heads.
  • Uneven head performance: mixing an old worn head with a new one can give colour or density differences across the print.
  • Capping and cleaning gaps: inadequate capping for the second head leads to drying and nozzle loss.
  • Software licensing: RIP drivers for the new configuration may require an update or new licence.
  • Warranty loss: modifying the machine may affect remaining warranty or AMC terms.

Many shops replace both heads during the upgrade so that both start with equal performance. That raises cost but avoids uneven output and simplifies maintenance planning.

Is your machine a good candidate for an upgrade?

Not every single-head printer is worth upgrading. Use the checklist below to judge honestly before spending money. The more points you can tick, the better the case for upgrading.

CheckGood signWarning sign
Machine ageLess than about four years, regularly maintainedOlder machine with no service history
Rails, bearings and beltsSmooth carriage movement, no noise or playCarriage wobble, noise, visible wear
Media feedAccurate feed, no slipping or skewFrequent feed banding or skewing
Heaters and dryingAll heaters working, good drying at current speedDrying already a bottleneck
Board systemCurrent, supported version with double-head optionsObsolete or locked board system
Power supplyRating confirmed adequate for two headsUnknown or already running near its limit
WorkloadRegularly turning away work or running overtimeMachine sits idle for parts of the day

If the machine shows wear in rails, bearings or feed, fix those first. A faster carriage with two heads exposes mechanical weaknesses more clearly, and banding from mechanical wear will not be solved by more heads. Our guide to carriage belts, rails and bearings explains how to judge their condition.

Special case: one XP600 to two i3200 heads

A popular request is to move from a single XP600 machine to two i3200 heads in one step. This combines a head type change and a head count change, so it is almost always a complete kit change rather than a carriage board swap. The i3200 is a larger head with more nozzles and needs its own head plate, dampers, capping station and board system. The carriage itself may need modification or replacement to fit two i3200 heads with correct spacing. In practice, this conversion is a major rebuild. It can work well on a strong frame with good mechanics, but the cost should be compared carefully with a factory-built double i3200 machine. Our article on i3200 vs XP600 printheads explains the head-level differences that drive these changes.

Questions to ask your supplier

  • Can you confirm from my mainboard photo and software version that a double-head carriage board will work?
  • If not, what is the price of a complete matching kit?
  • Which head plate, capping station and damper parts are needed for my machine?
  • Is my power supply adequate for two heads?
  • Will you provide firmware, software configuration and RIP settings?
  • Who does the calibration and colour profiling, and is it included?
  • What warranty covers the new board, heads and installation work?
  • How many days will the machine be out of production?

Further reading: Because a second head adds electrical load, it helps to understand how a switched-mode power supply works and why its rating matters.

Key takeaways

  • A single-to-double head upgrade by carriage board alone is possible only when the mainboard and firmware already support two heads.
  • Many budget machines need a new mainboard or a complete kit for a reliable upgrade.
  • The upgrade also needs a second head, head plate, capping station, dampers, ink lines, cables and calibration.
  • Compare the full upgrade cost and downtime against a new double-head machine with warranty.
  • Get written confirmation of compatibility and have the work done by a technician experienced with your board system.

Unified Engineering Dynamics can review your current machine, confirm whether a carriage board upgrade is possible, and compare it against a full kit or a new double-head printer so you choose the option that gives the best return.

More in the head carriage board series

Related: our fire board series explains the firing circuit that drives the heads, starting with What Is a Fire Board?, plus fire board failure signs and head voltage settings.

Related: our main board series covers main board functions and failure points, main board failure symptoms, the main board replacement checklist and how lightning, surges and earthing faults damage main boards.

For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.

Frequently Asked Questions

Can I add a second head just by changing the carriage board?

Only if your mainboard and firmware already support two heads and a matching double-head carriage board exists for your board version. Many entry-level machines need a new mainboard or complete kit.

Will two heads double my printing speed?

In production modes, a well-configured double-head machine can be close to twice as fast. In high-quality modes, or when drying limits speed, the gain is smaller.

Should I replace my old head when adding a second one?

It is often recommended. An old worn head and a new head can print with different density, which shows as banding or colour differences. Two new heads give more even output.

Do I need a new capping station for a double-head upgrade?

Yes. Each head needs proper capping and cleaning. Without it, the second head can dry out and lose nozzles quickly.

Is it better to upgrade or buy a new double-head printer?

If your machine is in good mechanical condition and the mainboard supports two heads, an upgrade can be cost-effective. If you need a complete kit and major mechanical parts, a new machine with warranty may be better value.

Will my RIP software work after the upgrade?

Usually it needs a new printer configuration or driver for the two-head layout, new calibration and new colour profiles. Check whether your RIP licence covers the new configuration.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *