Direct answer: A failing head board in an eco-solvent printer usually shows up in three ways: the software cannot detect one or more heads, whole colours or whole heads disappear from the nozzle check even though ink is reaching the head, or nozzles fire randomly and the print fills with garbage lines and blocks. The same symptoms can also be caused by the printhead, the head cable, the data cable, the power supply, the encoder or simply an ink supply problem. The fastest and cheapest way to a correct diagnosis is to rule out the simple causes first, observe the exact pattern of the fault, and only then suspect the board.
Recognising head board failure symptoms early helps you avoid replacing healthy printheads and shortens downtime.

Table of Contents
This guide explains each symptom, what it usually means, how to separate a head board fault from other faults, and what information to give your technician. It applies to common eco-solvent printers in India built on Hoson, Senyang, BYHX and similar board kits with Epson i3200, XP600, DX5 and DX7 heads. If you are new to the role of this board, first read our explainer on what the head carriage board does and why it fails.
Safety and ground rules before you start checking
Most of the checks in this article are observation-based and can be done by an operator. Anything involving opening the electronics, unplugging head cables or measuring voltages must be done with the power switched off and by someone trained to do so. Three rules prevent most self-inflicted damage:
- Never plug or unplug head cables or data cables with the printer switched on. This is one of the most common ways boards and heads are destroyed.
- Do not swap heads between boards or slots casually. If a head is shorted, moving it can damage a second board channel. If a board channel is faulty, it can damage a good head.
- Keep ink and cleaning fluid away from the electronics. Cover the carriage board when doing manual cleaning near the heads.
Symptom 1: Head not detected or head communication error
The print control software shows messages such as “head not found”, “head error”, “printhead not detected”, “head ID error” or the head status shows blank or red. Sometimes the printer refuses to print at all; sometimes it prints with one head missing.
What it usually means
The system cannot communicate with the head’s electronics. The chain involved is: mainboard, data cable, head board, (adapter board on some i3200 setups), head cable, and the head itself. A break or fault anywhere in that chain gives the same message.
How to narrow it down
| Observation | More likely cause |
|---|---|
| All heads not detected at once | Data cable, head board power, head board itself, mainboard communication or power supply |
| Only one head not detected on a multi-head machine | That head, its head cable, its adapter board or that channel of the head board |
| Fault started right after a head change | Cable inserted wrongly, wrong head type or settings, damaged new head, or board channel damaged during installation |
| Fault started after an ink leak or manual cleaning | Ink in the head connector or on the head board |
| Fault started after a power cut, storm or voltage fluctuation | Surge damage to power supply, head board or head |
| Fault comes and goes with carriage movement | Cracked or worn data cable, loose connector, cable chain pulling on connector |
| Fault appears only after the machine warms up | Heat-sensitive component or solder joint on the board, marginal cable contact |
A technician will typically confirm power reaching the head board, check the board’s indicator lights, inspect and reseat connectors (power off), and then test with a known-good cable before suspecting the board or head. Swapping a known-good head onto a suspect board, or a suspect head onto a known-good board, is done only after checking for signs of short circuit, because of the damage risk mentioned above.
Symptom 2: Whole colours or whole heads missing
The nozzle check shows that one or more colours are completely blank, or one head prints nothing while others are fine. In some cases, half a head (one group of nozzle rows) is missing.
Rule out ink supply first
Before suspecting electronics, confirm that ink is actually reaching the head. A completely missing colour is far more often an ink problem than a board problem. Check:
- Ink level in the tank or cartridge and whether the ink valve is open.
- Whether the damper for that colour is full or has air. Our damper checks guide explains what to look for.
- Kinked or blocked tubes and clogged ink filters, covered in our guides to ink filters and connectors and ink pumps and lines.
- Whether the capping station seals properly and whether cleaning pulls ink through. A missing colour that returns partly after cleaning points to a supply or clog problem, not electronics.
When the electronics become suspects
Electronics become more likely when ink clearly flows through the head during cleaning (you can see ink drawn into the waste), the nozzle check shows absolutely nothing for an entire head or a sharply defined group of rows, and the pattern does not change at all after cleanings. A sharply defined block of missing rows that exactly matches one connector or one channel strongly suggests a cable, connector or board channel fault. A gradually fading or patchy pattern suggests clogging or ink starvation instead.
Head or board?
A technician may check the head’s resistance and connector condition, inspect the head cable under good light for burnt or discoloured contacts, and look for burn marks on the head board near that channel. Discoloured contacts on both the cable and head connector suggest a short that may have damaged both ends. In that case, replacing only one part can lead to a repeat failure.
Symptom 3: Random firing, garbage prints and lines
The printer prints unexpected patterns: random dots across the media, repeated blocks of the image, solid bars, horizontal lines that are not in the file, or a nozzle check that looks different each time without any cleaning in between.
What it usually means
Random firing generally indicates corrupted data or unstable drive signals reaching the head. Possible causes include:
- A damaged or partly broken data cable between mainboard and head board, especially where it flexes in the cable chain.
- Electrical interference from poor earthing or nearby heavy equipment.
- A failing memory or processing chip on the head board or mainboard.
- Unstable power from a failing power supply, which can corrupt signals.
- A head cable with cracked tracks or ink in the connector.
- Wrong firmware or mismatched mainboard and head board versions.
- On the software side: a corrupt RIP file, wrong printer settings or a damaged installation of the print control software.
Quick checks that separate software from hardware
- Print the built-in nozzle check several times in a row. If it changes randomly with no cleaning in between, the fault is in hardware.
- Print a small, simple test file you know printed correctly before. If only certain files misprint, look at the RIP file and settings first.
- Try a different network cable or USB cable and port on the PC side. Communication faults between PC and mainboard can look like random printing.
- Note whether the random firing appears at a particular position on the carriage stroke. Position-related faults point towards cables flexing or the encoder.
Other symptoms worth knowing
Heads detected but no ink fires at all
If heads are detected, ink supply is confirmed, the nozzle check shows nothing from all heads, and cleaning draws ink normally, the drive section (the part of the board that generates the firing pulse) or the head voltage setting is a strong suspect. Check that the head voltage values in the software match the heads installed. If a separate fire board or driver board is used, it becomes a suspect too.
Weak, pale or faded output across a whole head
A head that prints but looks uniformly weaker than others may have a low voltage setting, a weak drive signal, or simply a partially clogged or ageing head. Compare with the voltage on the head label and with the setting in the software before suspecting the board. Our article on weak colour: printhead, ink supply or maintenance station explains the non-electronic causes.
Board gets hot, smells burnt or shows visible damage
A burning smell, discoloured areas, bulging capacitors, cracked components or melted connector housings are clear signs of a hardware fault. Switch off immediately and do not power the machine again until it has been inspected. Repeated power-on attempts with a shorted component can spread damage to the head and other boards.
Printer freezes or stops mid-print
Stopping during printing, with or without an error message, can come from data communication errors between head board and mainboard, a loose data cable, overheating, or a PC-side issue such as sleep settings, antivirus interference or a faulty network adapter. Rule out the PC side by checking that the PC does not go to sleep, and by trying another cable and port.
Banding or misalignment that appears suddenly
Sudden misalignment or banding is usually mechanical or encoder-related rather than a board fault. Check the encoder strip, media feed calibration and head alignment first. Our guide to narrowing down the cause of banding walks through the order of checks.
A practical diagnostic order
When a head-related fault appears, following a fixed order prevents unnecessary part replacements. The order below moves from cheapest and safest checks to more expensive and higher-risk steps.
| Step | Check | Who |
|---|---|---|
| 1 | Note the exact error message, nozzle check pattern and what happened before the fault | Operator |
| 2 | Confirm ink level, valves, dampers, tubes and cleaning performance | Operator |
| 3 | Restart PC and printer, check PC-to-printer cable and software settings | Operator |
| 4 | Check incoming power, stabiliser or UPS output and earthing | Electrician or technician |
| 5 | Power off, inspect head cables and data cable for creases, burns and ink, reseat correctly | Trained technician |
| 6 | Check head voltage settings and firmware versions | Trained technician |
| 7 | Inspect head board visually for burns, corrosion, ink residue and loose connectors | Trained technician |
| 8 | Measure supply voltages at the board and test with known-good cable | Trained technician |
| 9 | Test head and board separately using safe methods before swapping | Experienced technician |
| 10 | Decide repair, replacement or upgrade based on findings | Owner with technician |
Following this order matters because parts such as heads and boards are expensive, and the wrong swap at the wrong time can damage good parts. When the board is confirmed faulty, use our repair vs replace guide to decide the next step.
Head board failure symptoms: quick reference
| Symptom | Check first | Then suspect |
|---|---|---|
| All heads not detected | Power supply, data cable, board indicator lights | Head board, mainboard |
| One head not detected | Head cable seating and condition, adapter board | Head, board channel |
| Whole colour missing | Ink supply, damper, tubes, filters | Head cable, board channel, head |
| Block of rows missing, sharply defined | Head cable and connector | Board channel, head |
| Patchy or gradual missing nozzles | Clogging, cleaning, capping | Head condition |
| Random dots and garbage lines | Data cable, earthing, PC connection | Head board, mainboard, power supply |
| Heads detected but no firing | Head voltage settings | Drive section or fire board |
| Uniformly weak head | Voltage setting, cleaning, ink | Head wear, drive signal |
| Fault only after warm-up | Carriage fans and ventilation | Board components, solder joints |
| Burning smell or visible burn | Switch off immediately | Board and anything connected to it |
Why the head board is often blamed wrongly
Because the head board sits at the centre of the electronic chain, it is easy to blame for every head problem. In practice, a large share of “head board faults” reported to us turn out to be ink supply issues, cable damage or wrong settings. On the other hand, some genuine board faults are missed because a new head is fitted first, and that new head then fails too. Both mistakes cost money and production time. Clear observation and a fixed diagnostic order avoid most of them.
It also helps to keep a simple log: date, symptom, nozzle check photo, what was done, and the result. Over time, the log shows patterns, such as faults that always follow cleaning or power cuts, that point straight to the root cause. Our guide to recording and reporting nozzle checks shows how to capture this information in a useful way.
What to tell your technician or supplier
When you contact your service provider, give them:
- Printer model, head type and number of heads, board brand and version.
- Exact error text or a screenshot.
- Photos of the latest nozzle check and, if possible, earlier ones for comparison.
- When the problem started and what happened just before.
- Whether the fault is constant, intermittent, position-related or heat-related.
- What has already been checked or changed, including any parts swapped.
This lets a technician arrive with the right parts and test tools, or confirm remotely whether a board replacement is really needed. If you need replacement parts, our part identification guide explains how to match the exact board version.
Further reading: If you are new to structured fault finding, this short introduction to troubleshooting methods explains the general logic used here.
Key takeaways
- Head not detected, whole colours missing and random firing are the three classic head board symptoms, but each also has non-board causes.
- Always confirm ink supply before suspecting electronics for a missing colour.
- Sharply defined, unchanging missing blocks point towards cables, connectors or a board channel; gradual or patchy loss points towards clogging.
- Random patterns that change every test indicate a hardware data or power problem, not a clog.
- Never hot-plug cables and never swap heads and boards without checking for shorts first.
- Follow a fixed diagnostic order and keep a fault log to avoid wasting money on wrong parts.
More in the head carriage board series
- Eco-Solvent Head Carriage Board Explained
- Hoson vs Senyang vs BYHX Carriage Boards
- Single-Head vs Double-Head Carriage Board Upgrade
- How Ink Leaks and Solvent Vapour Damage the Carriage Board
- Head Cable vs Carriage Board: Finding the Fault
- Carriage Board Replacement Checklist
- Burnt Head Board After Printhead Change
- Carriage Board Price in India
- Carriage Board Connectors: Handling Rules
Related: our fire board series explains the firing circuit that drives the heads, starting with What Is a Fire Board?, plus fire board failure signs and head voltage settings.
Related: our main board series covers main board functions and failure points, main board failure symptoms, the main board replacement checklist and how lightning, surges and earthing faults damage main boards.
For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.
Frequently Asked Questions
How do I know if the problem is the head or the head board?
Look at the pattern. A problem that affects all heads at once points towards the board, data cable or power. A problem limited to one head may be that head, its cable or one board channel. A technician confirms by checking for shorts and testing with known-good parts in a safe order.
Can a missing colour be caused by the head board?
Yes, but it is less common than ink supply problems. If ink clearly flows during cleaning and the colour is completely and consistently missing, the head cable, connector, board channel or head becomes a suspect.
Why does my nozzle check change every time without cleaning?
A nozzle check that changes randomly without cleaning usually indicates unstable data or power, such as a damaged data cable, poor earthing, a failing power supply or a faulty board, rather than a clog.
Is it safe to swap heads between slots to test them?
Only after a technician has checked that neither the head nor the board channel is shorted. Swapping a shorted head onto a good channel, or a good head onto a damaged channel, can destroy the second part.
My printer shows head error after an ink leak. What should I do?
Switch off immediately and keep it off. Have a technician remove the ink from the connectors and board and inspect for damage before powering on again. Powering on with ink in a connector can turn a cleanable problem into a burnt board.
Can software problems look like head board failure?
Yes. Wrong printer settings, corrupt RIP files, PC sleep settings or a faulty PC network port can cause stops or strange prints. Testing with the built-in nozzle check and a known-good file helps separate software from hardware.