UV Printing

UV Flatbed Board Compatibility: Matching Boards to i3200, XP600, Ricoh and Konica Heads

UV Flatbed Board Compatibility: i3200, Ricoh and Konica Guide

Direct answer: UV flatbed board compatibility depends on five things matching: the board system (Hoson, Senyang or BYHX), the head type (XP600, TX800, i3200-U1, Ricoh Gen5/Gen6, Konica or Kyocera), the head count, the board version and firmware, and the software and RIP. Main board, head board and driver boards must all come from the same system and compatible versions; a board built for XP600 cannot drive i3200, and a Ricoh Gen5 board will not run Gen6 heads unless the supplier confirms it. Flatbed features such as Z-axis, height sensing and vacuum control must also be supported. Always confirm compatibility in writing with photos of your existing boards before buying.

Getting UV flatbed board compatibility right the first time avoids the most common and expensive mistake flatbed owners make: buying a board that will not work.

UV Flatbed Board Compatibility: i3200, Ricoh and Konica Guide
UV Flatbed Board Compatibility: i3200, Ricoh and Konica Guide

Buying the wrong board is one of the most common and expensive mistakes UV flatbed owners make. This guide explains the compatibility rules and gives practical tables for common configurations. It follows our article on i3200-U1 head voltage.

The five compatibility factors

FactorWhy it matters
Board systemDifferent communication, firmware and software
Head typeDifferent connectors, driver circuits and waveforms
Head countBoards have a fixed number of channels
Version and firmwareBoards from the same brand may not communicate across versions
Software and RIPMust support the system, heads and configuration

Head and board compatibility table

HeadCompatible board typesNot compatible with
XP600XP600-specific Hoson or Senyang boardsi3200, TX800 or Ricoh boards
TX800TX800-specific boards (some shared with XP600 on certain kits)i3200 or Ricoh boards
i3200-U1i3200-specific Hoson or Senyang boards (some BYHX)XP600 boards
Ricoh Gen5/Gen5iRicoh Gen5 BYHX or Hoson boardsEpson boards; Gen6 boards unless confirmed
Ricoh Gen6Gen6-capable BYHX or Hoson boardsGen5-only boards
Konica 1024iKonica-specific BYHX or Hoson boardsRicoh or Epson boards
KyoceraKyocera-specific industrial boardsOthers

For head comparisons, see Konica vs Ricoh vs Epson printheads.

Version matching within a system

Hoson, Senyang and BYHX release new board versions over time. A newer head board may not work with an older main board, or may need a firmware update. When replacing one board, record the version of every board in the set and the software version. Send photos to the supplier and ask them to confirm the exact version. If your version is no longer available, a full kit may be needed.

Flatbed feature compatibility

FeatureCheck
Z-axis motorMain board supports Z control and limit switches
Height sensorBoard input and software support
Anti-collisionInput available and configured
Vacuum zonesOutputs and relay support
Dual Y motorsMain board and drivers support gantry sync
RotarySoftware and board support rotary mode
White and varnishChannel count and licence
Lamp controlOutputs for leading and trailing lamps

A board that drives your heads correctly but lacks Z-axis or vacuum support will not run your flatbed properly.

Cable and adapter compatibility

Cables and adapters must match the board and head. i3200 cables differ from XP600 cables in pin count and pitch. Ricoh adapters differ between Gen5 and Gen6. Lengths matter too: a cable too short strains connectors, while one too long can pick up noise. Order cables by part number or with photos.

Software and RIP compatibility

Print control software must match the board system and version. RIPs must support the printer configuration and board system. When changing heads or boards, confirm the RIP supports the new setup and that you have the right profiles. Licences may limit head count or white and varnish channels.

UV flatbed board compatibility checklist

  1. Photograph all boards (both sides), labels and versions.
  2. Record head type, count and layout.
  3. Record software version and RIP.
  4. List flatbed features used: Z-axis, height sensor, collision, vacuum, rotary, white, varnish.
  5. Send all information to the supplier.
  6. Get written confirmation of compatibility, firmware needs and included cables.
  7. Check return policy if the board does not work.

Common compatibility mistakes

MistakeResult
Buying by head type onlyVersion mismatch
Assuming Gen5 and Gen6 boards are interchangeableBoard will not drive heads
Using XP600 board for i3200Will not work
Ignoring flatbed featuresZ-axis or vacuum not working
Forgetting licencesExtra channels locked

Upgrades and compatibility

Changing head type, for example from XP600 to i3200-U1 or from Ricoh Gen5 to Gen6, nearly always requires new boards, cables and software settings. See our UV flatbed head upgrade guide.

Example: Gen5 board for Gen6 heads

A unit planning to upgrade a 2513 to Ricoh Gen6 heads assumed its BYHX Gen5 boards would work. The supplier confirmed they would not. The upgrade required new head boards, cables and software, which changed the project budget.

Example: version mismatch

A Lucknow trophy maker ordered a Hoson i3200 head board online. It was a newer version, and the main board did not recognise it. The supplier provided a firmware update for the main board, but only after several days.

UV flatbed board compatibility by machine size

MachineTypical headsTypical board systemKey compatibility checks
A3 desktop1โ€“2 ร— XP600 or i3200-U1Hoson or SenyangHead type, rotary support, Z-axis
A2 / 60902โ€“4 ร— i3200-U1Hoson or SenyangHead count, white/varnish licence, vacuum
1313 / 16103โ€“4 ร— i3200-U1 or RicohHosonGantry type, dual Y motors
25134โ€“8 ร— Ricoh Gen5/Gen6BYHX or HosonHead generation, driver boards, fibre link
3020+8+ ร— Ricoh, Konica or KyoceraBYHXMachine maker customisation

Compatible clone boards

Some suppliers sell boards described as “compatible” with a given system. These may be clones of popular Hoson or Senyang designs. Some work well; others have firmware differences, weaker components or missing features. If you consider a clone, ask whether it works with your existing main board version and software, what warranty applies, and whether other customers use it in similar machines. Avoid mixing clones and originals in one set unless the supplier confirms compatibility.

Firmware compatibility

Firmware is the software inside each board. Main boards and head boards must run firmware versions designed to work together. When a new board arrives with different firmware, the software may refuse to connect or may show errors. Only update firmware with files supplied for your exact board pair, following the supplier’s instructions, with stable power from an online UPS. Interrupting a firmware update can make a board unusable. See UV flatbed firmware update guide.

Compatibility of lamps and power supplies

Board compatibility is not only about heads. Lamp drivers, power supplies and motor drivers must match the main board’s control signals and voltages. Replacing a UV LED lamp with a different model may require a different power supply or control signal. Replacing a motor driver may need parameter settings. Always check these items with the supplier as part of any electronics change. Our UV flatbed compatibility table brings heads, boards and lamps together.

Documenting your configuration

Create a single page describing your machine’s electronics: board system, model and version of each board, firmware versions, head types and serials, head layout, cable part numbers, lamp model and power supply, motor drivers, software and RIP versions, and licence details. Update it after every change. When something fails, this page lets any supplier confirm compatibility in minutes.

ItemExample entry
Board systemHoson, network version
Main boardModel, version, firmware
Head boardModel, version, firmware, head count
Headsi3200-U1 ร— 3 (CMYK, W, V), serials
LampsModel, wavelength, cooling type
SoftwarePrint control version, RIP version

When compatibility cannot be confirmed

If a supplier cannot confirm compatibility from your photos and details, do not buy on hope. Ask another supplier, contact the machine maker, or consider a complete matching kit. Buying a board that may not work costs money and, more importantly, downtime.

UV flatbed board compatibility for cables and adapters

ItemMust matchCommon mistake
Head data cableHead type, pin count, pitch, length, connector orientationUsing XP600 cable on i3200
Adapter / transfer boardHead type and board systemUsing Gen5 adapter for Gen6
Main data cableBoard system, length, connectorWrong length strains connectors
Fibre linkConnector type, lengthBending too tightly
Power cablesVoltage, current rating, connectorUndersized wire

Compatibility when buying a used flatbed

A used flatbed’s electronics determine how easy it will be to maintain. Before buying, photograph and identify all boards, check that spares for those versions are still available, confirm the software licence transfers with the machine, and check the head type and condition. A cheap machine with discontinued boards can become expensive when the first board fails. See our used UV flatbed electronics check.

Mixing new and old boards

When replacing one board in an older set, the new board may be a newer version. Sometimes this works with a firmware update to the other boards; sometimes it does not. Ask the supplier specifically: “Will this version work with my existing main board version X and software version Y?” If they cannot confirm, consider replacing the set together.

Software licences and compatibility

Print control software licences are often tied to the main board or a dongle and may limit head count, head type, white and varnish channels or features such as rotary printing. When upgrading boards or heads, check that the licence covers the new configuration. Licence upgrades may cost extra and take time to arrange.

Compatibility and warranty

Using incompatible or unapproved parts can void warranties on boards and heads. If your machine is still under warranty, check with the machine supplier before fitting third-party boards, cables or heads. Keep invoices and part details for every replacement.

Practical example of a compatibility request

A good request to a supplier might read: “Hoson network version kit on A2 flatbed, main board model and version shown in photo 1, head board in photo 2, three i3200-U1 heads (CMYK, white, varnish), print software version shown in photo 3, RIP shown in photo 4. Z-axis, height sensor, collision switch and four vacuum zones in use. Head board channel 2 burnt. Please confirm a replacement head board that works with this main board without firmware change, and quote cables.” Requests like this get accurate answers quickly.

Compatibility questions summary

  1. Same board system as my existing boards?
  2. Correct head type and generation?
  3. Enough channels for my head count, including white and varnish?
  4. Version and firmware compatible with my main board?
  5. Supports Z-axis, height sensor, collision, vacuum, rotary and lamp control as used?
  6. Correct cables and adapters included or available?
  7. Software and RIP support, and licence coverage?
  8. Warranty and return terms if it does not work?

If the answer to every question is a confident yes in writing, the purchase is low risk. Any uncertain answer is a reason to pause and ask more questions before paying.

Compatibility and future upgrades

When choosing boards for a new machine or a major repair, think ahead. If you may add white or varnish heads, choose a board with spare channels. If you may move from XP600 to i3200-U1, consider going straight to i3200 boards. If your RIP PC is far from the printer, choose a network version. A little planning now avoids buying a second set of boards within a year, and keeps your configuration simple for technicians and operators.

Bottom line

UV flatbed board compatibility depends on system, head type, head count, version and software, plus flatbed features. Photograph and record everything, confirm compatibility in writing, and remember that changing head types usually means a full board kit.

Further reading: Version matching is really about firmware: the boards must run code designed to talk to each other.

Key takeaways

  • Main, head and driver boards must come from the same system and compatible versions.
  • Boards are head-specific: XP600, i3200, Ricoh Gen5, Gen6 and Konica differ.
  • Check flatbed features such as Z-axis, height sensor and vacuum.
  • Cables, adapters, software and licences must match.
  • Get written compatibility confirmation before buying.

More in the UV flatbed head driver board series

Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.

Running a UV roll to roll machine as well? The matching guide in our roll to roll series is UV Driver Board Compatibility: Ricoh, Konica, Kyocera, Epson.

Frequently Asked Questions

What determines UV flatbed board compatibility?

Board system, head type, head count, version and firmware, and software and RIP support.

Can an XP600 board drive i3200 heads?

No. i3200 heads need i3200-specific boards.

Are Ricoh Gen5 and Gen6 boards interchangeable?

Not usually. Confirm with the supplier.

Do board versions matter?

Yes. Different versions may not communicate without firmware updates.

Can I mix Hoson and Senyang boards?

No. All boards must come from the same system.

What flatbed features should I check?

Z-axis, height sensor, anti-collision, vacuum zones, dual Y motors, rotary, white, varnish and lamp control.

Do cables need to match?

Yes. Pin count, pitch, connector type and length must match.

Does my RIP need to support the boards?

Yes. Confirm RIP support for the system and configuration.

Can licences limit compatibility?

Yes. Licences may limit head count or white and varnish channels.

What should I send the supplier?

Photos of all boards, versions, head details, software version and features used.

Is a full kit easier than single boards?

Often, if versions are hard to match or heads are being changed.

Can Konica heads run on Ricoh boards?

No. They need Konica-specific boards.

What if my board version is discontinued?

A full kit may be required.

Can Unified Engineering Dynamics confirm board compatibility?

Yes. Send photos and details and our team will confirm compatible boards.

Are compatible clone boards safe to use?

Some work well, but confirm compatibility with your main board version, software and warranty first.

Can firmware differences stop a new board working?

Yes. Boards must run firmware versions designed to work together.

Do lamps and power supplies affect compatibility?

Yes. They must match the main board’s control signals and voltages.

What should my configuration record include?

Board models, versions, firmware, heads, cables, lamps, drivers, software, RIP and licences.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *