Direct answer: A UV flatbed i3200 head change burns the head board when a cable is plugged or unplugged with power on, a ribbon cable is inserted at an angle or one pin off, a damaged or shorted head is fitted, ink leaks onto connectors during the change, the wrong voltage is entered, or static from the operator or substrate discharges into the head. To change an i3200-U1 head safely, switch off and isolate power, use an anti-static strap, inspect the new head and cables, insert cables straight and fully, prime and check for leaks before power-up, enter the voltage from the head label, then test one head at a time. Following these steps protects a head worth about โน78,000โ95,000 and a carriage board worth hundreds of dollars.
A careless UV flatbed i3200 head change can burn a head worth about โน78,000โ95,000 and the board behind it within seconds.

Table of Contents
Epson i3200-U1 heads are now the most popular choice on A3, A2 and 6090 UV flatbeds because of their speed and resolution. They are also expensive and sensitive. This guide explains why head changes go wrong and how to do them safely. It builds on our carriage board replacement checklist.
About the i3200-U1 on UV flatbeds
The i3200-U1 is the UV-ink version of Epson’s i3200 head family. It has four rows of nozzles and is used for CMYK, white or varnish depending on the layout. Indian listings in 2026 priced genuine i3200-U1 heads at about โน78,000โ95,000, compared with about โน12,000โ15,000 for an XP600. See our i3200 vs XP600 comparison.
Using the wrong head variant matters: the i3200-U1 is intended for UV ink, while A1 and E1 variants are intended for water-based and eco-solvent inks. Fitting the wrong variant on a UV flatbed shortens head life.
Why head boards burn during head changes
| Cause | What happens |
|---|---|
| Hot-plugging | Connecting or disconnecting with power on causes voltage spikes that damage the driver channel and head |
| Angled or offset cable | Adjacent pins short, sending drive voltage to the wrong pins |
| Shorted head | A damaged head draws excessive current and burns the channel |
| Ink on connectors | UV ink bridges pins, causing shorts |
| Wrong voltage | Overdriving the head shortens its life; very wrong settings can cause damage |
| Static discharge | Operator or acrylic sheets discharge into exposed pins |
| Wrong head variant | Reduced compatibility and life with UV inks |
Before the head change
- Find out why the old head failed. If it was electrical, have the board channel tested first.
- Check the new head. Confirm it is genuine i3200-U1, inspect the nozzle plate and connectors, and note the voltage on the label.
- Check cables. Replace any cable that was connected to a failed head or shows damage.
- Back up settings. Record head voltages, temperatures, alignment and offsets.
- Prepare the area. Lint-free cloths, gloves, cleaning fluid compatible with your ink, anti-static strap, torch and magnifier.
Step-by-step head change
- Switch off the printer and disconnect mains power. Switch off lamps.
- Wait for the recommended discharge time.
- Wear an anti-static strap connected to machine earth.
- Close ink valves or clamp lines to the old head.
- Remove the carriage cover carefully.
- Disconnect the old head’s cables, pulling straight out after releasing locks.
- Remove the damper connections and the head mounting screws.
- Clean the mounting area and check for ink on the carriage board below.
- Fit the new head, tightening screws evenly without overtightening.
- Connect dampers and check for leaks.
- Inspect cable ends, then insert cables straight and fully, with correct orientation, and close the locks. Check under good light.
- Prime the head with ink and inspect for leaks with power still off.
- Refit covers, restore power and start the software.
- Enter the new head’s voltage from the label.
- Check detection and temperature, then run a nozzle check.
- Align the head mechanically and in software, and calibrate.
Priming and leak checks
UV ink leaking from a loose damper or line during priming can run onto connectors and the board. Always prime with power off, wipe away any spills, and check connections again before powering up. Cured UV ink on connectors is hard to remove and can cause intermittent faults.
Head voltage and temperature
Each i3200-U1 head carries a recommended voltage on its label. Enter it exactly in the print control software for that head channel. Set head temperature according to your ink maker’s guidance. See i3200-U1 head voltage settings.
If the new head does not work
| Symptom | Check |
|---|---|
| Head not detected | Cable orientation, seating, locks, cable damage, firmware |
| Missing rows | Priming, air, nozzle plate, cable seating |
| Temperature error | Heater connector, setting |
| Overcurrent error | Switch off immediately; check cable and head |
| Burning smell | Switch off immediately; inspect board and cables |
Static control during head changes
UV flatbed shops often handle acrylic and PVC sheets that build strong static. Before touching a head or board, touch earthed machine metal and wear an anti-static strap. Keep new heads in their anti-static packaging until fitting. Avoid working near freshly peeled acrylic. See board connectors and static handling.
Genuine vs refurbished heads
Refurbished or decrypted heads are sometimes offered at lower prices. Some are fine, but others have damaged nozzles or internal faults that can short a board channel. Buy from trusted suppliers and ask for test prints and warranty terms. Our guide to genuine and compatible parts identification explains what to check.
Example: hot-plug disaster
An operator in Noida reseated a white head cable with the machine on to fix an intermittent fault. The head and the white channel burnt instantly. The repair cost a new i3200-U1 head, a cable and a carriage board. A thirty-second shutdown would have prevented it.
Example: offset cable
A technician fitted a new head, but one cable was inserted one pin off. The head showed an overcurrent error. He switched off immediately, reinserted the cable correctly, and the head worked. Quick action saved the head and board.
Tools for a UV flatbed i3200 head change
| Tool or supply | Purpose |
|---|---|
| Anti-static wrist strap | Prevents static damage to head and board |
| Screwdrivers of correct size | Avoid stripping head mounting screws |
| Nitrile gloves | Protect skin from UV ink |
| Lint-free cloths and swabs | Clean nozzle area and spills |
| Cleaning fluid compatible with your ink | Remove uncured ink |
| Syringe and tubing | Prime the head |
| Bright torch and magnifier | Check cable insertion |
| Calipers or feeler gauges | Check head height |
| Masking tape and marker | Label cables and lines |
| Phone camera | Photograph connections before removal |
UV inks can irritate skin and eyes. Follow the safety advice in our UV ink handling and operator safety guide.
Diagnosing why the old head failed
Before fitting a new head, work out why the old one failed. Common causes on UV flatbeds include cured ink in nozzles from reflection or poor capping, physical damage from a crash, electrical damage from hot-plugging or a board fault, and wear after long service. Each cause needs a different fix:
| Failure cause | Evidence | Fix before fitting new head |
|---|---|---|
| Cured ink | Hard deposits on nozzle plate | Check lamp shields, capping, idle settings |
| Crash damage | Scratches, dents | Fix height setting habits and sensors |
| Electrical damage | Overcurrent errors, burn marks | Test board channel and cable |
| Wear | Gradual nozzle loss after long use | Normal replacement |
| Ink incompatibility | Swelling, leaks | Check ink is suitable for i3200-U1 |
Head alignment after the change
A new i3200-U1 head must be aligned with the others to avoid banding and misregistration between colour, white and varnish. Typical steps:
- Check head height with calipers or the machine’s reference so the nozzle plate sits level with the other heads.
- Print the head angle test and adjust the head’s rotation screw until lines are straight.
- Print vertical alignment tests and adjust in software or mechanically.
- Run bidirectional calibration for each print mode.
- Run step or feed calibration as required by your machine.
- Print a test image with fine text, gradients, white and varnish.
Capping and idle care for new heads
New heads last longer with good capping. At the end of each shift, park the carriage on the capping station and make sure caps seal properly. Clean capping station sponges and wiper blades regularly. For short idle periods, use the software’s automatic flash or spit settings to keep nozzles wet. UV ink should never be left exposed to light on the nozzle plate. See our UV printer maintenance schedule and head care guide.
XP600 vs i3200-U1 head change differences
| Aspect | XP600 | i3200-U1 |
|---|---|---|
| Indian price (2026) | About โน12,000โ15,000 | About โน78,000โ95,000 |
| Cables | Ribbon cables, fine pitch | Ribbon cables, fine pitch, more conductors |
| Board | XP600-specific board | i3200-specific board; not interchangeable |
| Voltage setting | Set per head | Set per head from label |
| Risk of costly mistakes | Moderate | High |
The basic steps are similar, but the i3200’s higher price makes every precaution more important.
Warranty and documentation
Most head suppliers do not cover heads damaged by electrical faults, crashes or incorrect handling. Keep evidence that the head was installed properly: photos of the head label and serial, photos of correct cable insertion, the voltage entered, and the first nozzle check print. If the head fails early, this documentation helps support a claim. Buy heads from suppliers who provide test prints before shipping.
When to ask for professional help
If you have never changed an i3200 head, if the old head failed electrically, or if the machine has a history of burnt boards, ask a technician for the first change. Watch and learn the steps. Many owners handle later changes themselves once they have seen it done correctly.
UV flatbed i3200 head change: common mistakes and their cost
| Mistake | Possible damage | Typical cost impact |
|---|---|---|
| Hot-plugging a cable | Head and board channel burnt | New head (about โน78,000โ95,000) plus board |
| Cable one pin off | Overcurrent, possible burn | Head and/or board |
| Fitting head to untested channel | New head destroyed | New head |
| Ink spilled on connectors | Short, corrosion | Cable, adapter, board |
| Guessing voltage | Poor print, shorter head life | Early head replacement |
| Skipping alignment | Banding, misregistration | Wasted substrates |
| Wrong head variant | Reduced life with UV ink | Early replacement |
Head change on multi-head i3200 machines
On three- and four-head i3200 machines, heads are mounted close together, and access is tight. Remove only the head being changed, and protect the neighbouring heads’ nozzle plates from drips and tools. Label each head’s ink lines and cables before disconnection. After fitting, check that the new head sits at exactly the same height as its neighbours, because even small differences affect gloss and dot size, especially between white and colour heads.
Keeping a head history
Record each head’s serial number, installation date, voltage setting, position, ink type and replacement reason. Over time this history shows average head life on your machine, highlights positions that fail more often (often white), and helps you plan head purchases and budgets. It also supports warranty discussions with suppliers.
Cost planning for head changes
Most busy shops replace i3200 heads every so often depending on usage, ink quality and maintenance. Build head replacement into your pricing by estimating cost per square metre or per job. Shops that treat heads as a running cost rather than a surprise are better able to buy genuine parts and avoid risky cheap alternatives.
Checking the capping station after a head change
A new head is only as healthy as the capping station that protects it overnight. After any head change, inspect the cap for that head: the rubber lip should be clean, soft and level, and the cap should rise fully to seal against the nozzle plate. Replace hardened or torn caps, clean the wiper blade, and check that the cleaning pump draws ink properly. A poor seal lets UV ink dry and cure on the nozzle plate, undoing the benefit of an expensive new i3200-U1 head within days. Many shops replace caps and wipers at the same time as the head.
Bottom line
Most burnt head boards after a UV flatbed i3200 head change are caused by hot-plugging, misaligned cables, shorted heads, ink leaks, wrong voltages or static. Switch off, earth yourself, inspect heads and cables, insert cables carefully, prime with power off, enter the correct voltage and test one head at a time. These habits protect both your heads and your boards.
Further reading: The i3200-U1 is a piezo head; this overview of inkjet printing explains how such heads fire droplets.
Key takeaways
- Never plug or unplug head cables with power on.
- Insert ribbon cables straight, fully and with correct orientation.
- Test the board channel before fitting a new head after an electrical failure.
- Prime with power off and check for leaks.
- Enter the voltage from the head label and control static.
More in the UV flatbed carriage board series
- UV Flatbed Carriage Board Explained
- UV Flatbed Head Board Failure Symptoms
- Hoson vs Senyang vs BYHX UV Flatbed Boards
- Adding White and Varnish Heads to a UV Flatbed
- Head Crashes, UV Reflection and Board Damage
- UV Flatbed Head Cable vs Carriage Board Fault
- UV Flatbed Carriage Board Replacement Checklist
- UV Flatbed Carriage Board Price in India
- UV Flatbed Board Connectors and Static
Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.
Running a UV roll to roll machine as well? The matching guide in our roll to roll series is Burnt Head Board After a Ricoh Head Change.
Frequently Asked Questions
Why do head boards burn after an i3200 head change?
Hot-plugging, misaligned cables, shorted heads, ink on connectors, wrong voltage and static are the main causes.
How much does an i3200-U1 head cost in India?
Indian listings in 2026 ranged from about โน78,000 to โน95,000.
Which i3200 variant should I use on a UV flatbed?
The i3200-U1 is the UV-ink variant. A1 and E1 variants are for water-based and eco-solvent inks.
Can I reseat a head cable with the power on?
No. Always switch off and isolate power first.
Where do I find the head voltage?
On the head label. Enter it exactly for that channel.
What should I do if I see an overcurrent error?
Switch off immediately and check cable seating and the head.
Should I replace the cable with the head?
Replace any cable connected to a failed head or showing damage.
How do I prevent ink leaks during priming?
Prime with power off, check damper connections and wipe any spills before powering up.
Can static damage a new head?
Yes. Use an anti-static strap and keep heads in their packaging until fitting.
Are refurbished i3200 heads safe?
Some are, but others have faults. Buy from trusted suppliers with test prints and warranty.
Why is my new head not detected?
Check cable orientation, seating, locks, damage and firmware.
Should I test the board after a head failure?
Yes. A damaged channel can destroy a new head.
How long does a head change take?
Usually one to two hours including priming and alignment.
Can Unified Engineering Dynamics supply i3200-U1 heads?
Yes. Our team supplies i3200-U1 heads, cables and boards and can advise on safe fitting.
What tools do I need to change an i3200 head?
An anti-static strap, correct screwdrivers, gloves, lint-free cloths, compatible cleaning fluid, syringe, torch, magnifier and labels.
How do I align a new i3200 head?
Check height, adjust head angle, run vertical and bidirectional alignment and calibration, then print a test image.
Is an XP600 board compatible with an i3200 head?
No. i3200 heads need i3200-specific boards.
How do I protect neighbouring heads during a change?
Remove only the head being changed, label lines and cables, and cover neighbouring nozzle plates from drips.