Direct answer: A successful UV carriage board replacement follows a clear sequence: confirm the diagnosis and root cause, identify the exact board brand, model and version, order a compatible board, back up all settings and head data, switch off and isolate the machine, remove the old board with static precautions, install the new board and cables correctly, check power and settings before connecting heads, then test, calibrate and monitor. Skipping any step risks damaging the new board or heads, or wasting money on a board that was not the real problem.
A careful UV carriage board replacement restores production in hours, while a rushed one can destroy a new board or a Ricoh head.

Table of Contents
Replacing a carriage board on a UV roll to roll printer is a job that combines electronics, software and careful handling of expensive printheads. Done well, it restores production within hours. Done poorly, it can destroy a new board or a Ricoh head worth more than a lakh of rupees. This checklist is designed for owners and technicians working on UV machines with Ricoh Gen5, Gen5i, Gen6, Konica 1024i, Kyocera or Epson i3200-U1 heads. For background, see our guide to the UV roll to roll carriage board.
Stage 1: Confirm the diagnosis
Before ordering anything, be sure the carriage board really is the problem.
- Record the symptoms with nozzle checks, error messages and photos.
- Rule out ink supply, negative pressure, head temperature and software settings.
- Test cables with swap tests and known good spares.
- Swap heads or channels to see whether the fault follows the head or stays with the board.
- Check that the fault is not upstream, in the mainboard or data link.
Our guides on UV head board failure symptoms and head data cable versus board faults walk through these tests.
Stage 2: Find the root cause
A carriage board rarely fails for no reason. Before installing a new one, identify what damaged the old one, otherwise the new board may fail in the same way:
- Is lamp cooling working? Are fans, filters and chiller in good condition?
- Is there ink contamination from leaks or mist?
- Is earthing good, and are anti-static brushes in place?
- Was there a recent head change, storm or power event?
- Are any heads shorted? A shorted head can destroy a new board immediately.
- Is the power supply output correct and stable?
Have a technician measure power supply voltages and check heads for shorts before the new board is connected.
Stage 3: Identify the board exactly
- Photograph the board in place, showing all connectors and labels.
- Note brand, model and version numbers printed on the board.
- Note the mainboard brand and version.
- Note the print control software name and version.
- Note the head type, head count and channel layout, including white and varnish.
- Note the machine brand, model and serial number.
Stage 4: Order the right board
- Send photos and details to the supplier, and ask them to confirm compatibility in writing.
- Confirm whether the board is new, refurbished or used.
- Ask whether firmware or authorisation is needed.
- Confirm warranty terms and the return process.
- Consider ordering spare cables at the same time.
For help choosing between board systems, see our guide to Hoson, Senyang and BYHX carriage boards, and for current price ranges, see UV roll to roll carriage board prices in India.
Stage 5: Back up everything
Before touching the machine, back up:
- Print control software settings files.
- Head voltage and waveform settings for each head.
- Head temperature settings.
- Calibration values: head alignment, bidirectional correction, step and feed.
- White, varnish and channel mapping settings.
- Lamp and negative pressure settings, if stored in the software.
Write down critical values on paper as well as saving files. Photograph the settings screens.
Stage 6: Prepare the work area
- Switch off the machine and unplug it from the mains. Wait for capacitors to discharge as advised by your supplier.
- Switch off and isolate lamps and chiller.
- Wear an anti-static wrist strap connected to a proper earth point.
- Prepare a clean, dry surface and anti-static bags for removed parts.
- Have good lighting and the right tools.
- Protect heads from dust and light, and cap them if possible to prevent drying.
Stage 7: Remove the old board
- Photograph all connections before disconnecting anything.
- Label each cable with its connector position.
- Release locking tabs before removing flat cables; pull straight, not at an angle.
- Remove screws and standoffs carefully; keep them in a container.
- Place the old board in an anti-static bag and label it for warranty or repair.
Stage 8: Inspect before installing
- Inspect the new board for shipping damage, bent pins or loose components.
- Compare it with the old board: connectors, layout and version.
- Inspect cables and connectors for wear, ink or damage; replace any doubtful cables.
- Clean the mounting area of ink residue and dust.
Stage 9: Install the new board
- Mount the board with the original screws and standoffs, ensuring no contact with metal parts that could cause shorts.
- Connect power and data cables according to your photos and labels.
- Insert flat cables straight and fully, then close locking tabs.
- Leave the head cables disconnected for the first power-up if your technician recommends this, so that power and communication can be checked without risking heads.
- Route cables as originally, with no twists or tension.
Stage 10: First power-up and checks
- Power on and observe for smoke, smell or unusual sounds; switch off immediately if anything seems wrong.
- Check that the software detects the carriage board.
- Have the technician measure key voltages on the board.
- Load firmware or authorisation if required.
- Enter head voltage, waveform and temperature settings from your backup before connecting heads.
- Switch off, connect heads, then power on again.
Stage 11: Test heads
- Confirm all heads are detected.
- Check that head temperatures rise to set points.
- Run nozzle checks and purge as needed.
- Watch for missing heads, unusual patterns or errors.
Stage 12: Calibrate
- Run head alignment and bidirectional calibration.
- Check step and feed calibration.
- Verify white and varnish alignment if used.
- Print colour test charts and compare with previous output.
Stage 13: Production test and monitoring
- Run a typical production job for at least an hour.
- Monitor for heat-related faults, especially on warm days.
- Record the replacement in the machine logbook: date, board details, settings and cause of failure.
- Keep the old board for warranty claim or repair evaluation.
Printable UV carriage board replacement checklist
| Step | Check | Done |
|---|---|---|
| 1 | Diagnosis confirmed with swap tests | ☐ |
| 2 | Root cause identified and fixed | ☐ |
| 3 | Heads checked for shorts | ☐ |
| 4 | Power supply voltages verified | ☐ |
| 5 | Board brand, model and version identified | ☐ |
| 6 | Compatibility confirmed in writing | ☐ |
| 7 | Settings and calibrations backed up | ☐ |
| 8 | Machine, lamps and chiller isolated | ☐ |
| 9 | Anti-static precautions in place | ☐ |
| 10 | Connections photographed and labelled | ☐ |
| 11 | New board inspected | ☐ |
| 12 | Cables inspected or replaced | ☐ |
| 13 | Board installed and cables routed | ☐ |
| 14 | First power-up checks done | ☐ |
| 15 | Head settings entered | ☐ |
| 16 | Heads connected and tested | ☐ |
| 17 | Calibration completed | ☐ |
| 18 | Production test passed | ☐ |
| 19 | Logbook updated | ☐ |
Common mistakes
- Replacing the board without confirming the diagnosis.
- Not checking heads for shorts, so the new board is damaged immediately.
- Ordering by appearance instead of exact version.
- Forgetting to back up head settings.
- Hot-plugging cables or heads.
- Inserting flat cables at an angle.
- Leaving the root cause, such as poor cooling or leaks, unfixed.
Example: a smooth replacement
A unit in Indore had a confirmed carriage board failure caused by ink ingress from a leaking damper. Before ordering, the technician photographed the board, confirmed the version with the supplier and checked heads for shorts. The damper was replaced and a drip shield fitted. Settings were backed up. The new board arrived in three days, was installed in two hours, and after calibration, production resumed the same day.
Example: a second board lost to a shorted head
Another unit replaced a burnt carriage board without checking the heads. The new board failed within seconds of power-on. A technician later found that one head had an internal short, which had caused both failures. Testing the heads first would have saved the cost of the second board.
Planning for downtime
A carriage board failure usually stops production. Good planning reduces the impact:
- Know your supplier in advance. Identify one or two reliable suppliers for your board system before you need them.
- Keep board details ready. A machine file with photos, versions and software details lets you order within minutes.
- Consider a spare board. For machines that run busy seasons, a tested spare carriage board may pay for itself by preventing several days of lost production.
- Arrange backup printing. Agree with a partner unit to print urgent jobs during breakdowns.
- Tell customers early. If deliveries will be late, informing customers early protects relationships.
Firmware and authorisation details
Some replacement boards arrive with firmware that does not match your mainboard or software. In that case, the software may not recognise the board, or some features may not work. Your supplier should confirm whether the board is preloaded with the correct firmware and, if not, provide the file and procedure. Never load firmware from an unknown source, and never interrupt a firmware update, because a failed update can make a board unusable.
Machines with authorisation systems may need a code from the original supplier after a board change. Contact the supplier before the job, so the code is ready when the board is installed. If the original supplier is no longer available, ask your board supplier whether the replacement is supplied without authorisation requirements.
Head settings: getting them right after replacement
After a carriage board replacement, head settings are among the most important values to restore. They typically include:
| Setting | Why it matters |
|---|---|
| Drive voltage per head | Too high stresses heads and driver circuits; too low causes weak jetting |
| Waveform selection | Must suit head type and ink |
| Head temperature set point | Controls UV ink viscosity for stable jetting |
| Head mapping and channel order | Ensures each colour prints from the right head |
| White and varnish channel settings | Controls layer printing and circulation timing |
Enter these from your backup before the first firing. If your backup is missing, use the data printed on each head and your supplier’s guidance; never guess.
Safety around UV lamps during the job
UV LED lamps emit intense ultraviolet light that can harm eyes and skin. During a board replacement, ensure lamps are switched off and isolated, so they cannot turn on unexpectedly during testing. When testing after installation, keep covers in place and avoid looking at lamps. Our guide to UV ink handling and operator safety covers safe practices with UV inks, which are also present during carriage work. Wear gloves when handling inked parts, as uncured UV ink can irritate skin.
Testing over several days
A board that works perfectly for an hour may still develop heat-related or intermittent faults. After replacement:
- Run normal production for several days while watching closely for errors.
- Note room temperature and lamp cooling performance during the hottest part of the day.
- Print nozzle checks at the start and middle of each shift and compare them.
- Keep the old board until you are confident the new one is stable and the warranty process, if needed, has started.
Warranty claims for failed boards
If the failed board was under warranty, contact the supplier promptly with photos, symptoms, test results and the purchase invoice. Many warranties exclude damage from surges, water, ink ingress or incorrect installation, so honest, detailed records help. Keep the failed board in an anti-static bag and do not attempt repairs that could void the warranty. Our guide on comparing UV spare parts suppliers and service covers warranty considerations when choosing suppliers.
Documenting the job
Record the replacement in the machine logbook:
- Date and technician.
- Symptoms and diagnosis.
- Root cause and the corrective action taken.
- Old and new board details, including versions and serial numbers.
- Settings restored and any changes made.
- Test results and production performance afterwards.
This record speeds up future repairs and supports warranty claims.
Tools and materials for the job
| Item | Use |
|---|---|
| Anti-static wrist strap and mat | Protect boards and heads from static |
| Correct screwdrivers and nut drivers | Remove and fit board mounting screws without damage |
| Multimeter | Check power supply voltages and continuity |
| Labels and marker | Mark cables and connector positions |
| Camera or phone | Photograph every connection before removal |
| Lint-free swabs, cloths and suitable cleaning fluid | Clean mounting area and connectors |
| Absorbent pads | Catch ink drips from the carriage |
| Anti-static bags | Store old and spare boards |
| Spare cables | Replace worn cables during the job |
| Gloves | Protect hands from uncured UV ink |
Having everything ready before starting keeps the machine open for the shortest possible time and reduces the risk of contamination and mistakes.
Who should do the replacement
A carriage board replacement involves electronics, software settings and expensive heads. It should be done by a technician trained on your board system, or under remote guidance from your board supplier if your in-house technician is experienced. Operators can help by preparing settings backups, photos and the work area, and by describing symptoms clearly. If you are unsure, the cost of a qualified technician is small compared with the risk of damaging a new board or a Ricoh head worth more than a lakh of rupees.
Replacement cost overview
For a typical Ricoh Gen5 machine, the board itself is listed from about $287 to $650 on Chinese marketplaces before shipping, duty and GST, and Indian traders add import costs, margin and support. Add technician time, any cables or adapter boards replaced at the same time, and downtime. Compare this with the value of the heads on the carriage, often over ₹5 lakh at Indian trader prices, and the case for careful procedure is clear. Our guide to UV roll to roll carriage board prices gives more detail.
Further reading: Carriage boards are multilayer printed circuit boards, so physical damage and contamination can be hard to repair.
Key takeaways
- Confirm the diagnosis and find the root cause before a UV carriage board replacement.
- Check heads for shorts and verify power supply voltages before connecting a new board.
- Identify the exact board version and get compatibility confirmed in writing.
- Back up all settings, follow anti-static precautions, and never hot-plug.
- Test, calibrate and monitor after installation, and record everything.
More in the UV carriage board series
- UV Roll to Roll Head Carriage Board Explained
- UV Head Board Failure Symptoms
- Hoson vs Senyang vs BYHX Carriage Boards for Ricoh Gen5/Gen6
- Adding White and Varnish: Head and Carriage Board Upgrade
- UV Lamp Heat, Ink Mist and Carriage Board Damage
- Head Data Cable vs Carriage Board Fault
- Burnt Head Board After a Ricoh Head Change
- UV Roll to Roll Carriage Board Price in India
- UV Carriage Board Connectors, Pins and Static
Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.
Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine head carriage board and the eco-solvent head carriage board.
Frequently Asked Questions
How long does a carriage board replacement take?
Installation typically takes a few hours, plus calibration and testing. The main delay is usually sourcing the correct board.
Do I need to back up settings before replacing the board?
Yes. Back up head voltages, waveforms, temperatures, calibrations and channel mapping, both as files and on paper.
Why did my new carriage board fail immediately?
The most common reason is an unresolved root cause, such as a shorted head, faulty power supply or wrong settings. Check these before installing a new board.
Can I install a carriage board myself?
Experienced technicians can, but the risk to heads and boards is high. If you are not trained, use a qualified technician.
Should I connect heads during the first power-up?
Many technicians power up without heads first to check the board and settings, then connect heads after confirming voltages.
What anti-static precautions are needed?
Use an earthed wrist strap, anti-static bags and a clean work area, and avoid touching board components and connector pins.
Do I need new firmware for a replacement board?
Sometimes. Ask the supplier whether firmware or authorisation is needed for your board version.
Should I replace cables when replacing the board?
Inspect all cables and replace any that are worn, stiff, cracked or contaminated with ink.
What should I do with the old board?
Keep it in an anti-static bag for warranty claims or repair evaluation. Some boards can be repaired and kept as spares.
How do I know if a head is shorted?
A technician can test heads with appropriate instruments before connection. Never connect a suspected shorted head to a new board.
Does lamp cooling matter when replacing the board?
Yes. If poor cooling caused heat damage, fix it before installing the new board, or the new board may fail too.
What warranty should I expect on a replacement board?
Terms vary; some Chinese suppliers list three months. Confirm warranty terms and claim procedures before buying.