UV Printing

Burnt Ricoh Head Board After a Head Change: Causes and Prevention on UV Roll to Roll Printers

Burnt Ricoh Head Board After a Head Change: Causes and Fixes

Direct answer: A burnt Ricoh head board after a head change is usually caused by one of five things: connecting or disconnecting the head or its cable while the machine was powered, inserting the flat cable at an angle or in the wrong orientation, fitting a head with an internal short, entering wrong voltage or waveform settings, or ink and cleaning fluid entering the connector during installation. Prevention depends on strict power-off procedures, testing heads before connection, careful cable insertion, correct settings entered before the first firing, and keeping connectors dry and clean.

A burnt Ricoh head board after a head change is one of the most expensive mistakes on a UV printer, and almost always preventable.

Burnt Ricoh Head Board After a Head Change: Causes and Fixes
Burnt Ricoh Head Board After a Head Change: Causes and Fixes

Changing a Ricoh Gen5, Gen5i or Gen6 head is one of the most expensive routine jobs on a UV roll to roll printer. A new Ricoh Gen5 head costs around ₹1.25 lakh to ₹1.55 lakh from Indian traders, and Gen6 heads cost more. Yet many owners have experienced the worst outcome: the new head does not work, the head board channel is burnt, and sometimes another head stops working too. This article explains why it happens and how to prevent it. It forms part of our series on UV roll to roll electronics, which begins with the UV roll to roll carriage board explained.

How Ricoh heads connect to the board

Ricoh industrial heads connect to an adapter board or head board through a flexible cable supplied with the head. The cable carries print data, timing signals, firing voltage, and heater and thermistor connections. The head board supplies the firing waveform and controls the heater. Because the cable carries both delicate signals and higher-power circuits, a wrong connection can send voltage where it should not go, damaging the head, the board or both.

Cause 1: Hot-plugging

Connecting or disconnecting a head or cable while the machine is powered is the most common cause of burnt head boards. When a flat cable is inserted, its contacts do not all touch at the same instant. For a brief moment, some pins connect while others do not, so voltages can appear on pins that are not designed to carry them. The result can be instant damage to driver components, the head’s internal circuits or both.

Prevention

  • Always switch off and unplug the machine before connecting or disconnecting heads, cables or boards.
  • Wait for capacitors to discharge as advised by your supplier.
  • Make power-off a written rule for every operator and technician, with no exceptions.

Cause 2: Angled or reversed cable insertion

Flat cables must be inserted straight and fully into their connectors. If a cable goes in at an angle, adjacent contacts can short together, or the cable can make contact on one side only. Some connectors allow a cable to be inserted upside down, reversing the pin order. Either fault can send voltage to the wrong pins.

Prevention

  • Check cable orientation against the original or the board marking before insertion.
  • Insert cables straight, fully seated and evenly, then close locking tabs.
  • Use good lighting and, if needed, a magnifier to confirm correct seating.
  • Do not force a cable; if it resists, check alignment.

Cause 3: A head with an internal short

Heads can develop internal shorts from ink ingress, physical damage, manufacturing defects or previous electrical events. Used, refurbished or grey-market heads carry more risk. When a shorted head is connected, it can draw excessive current from the driver section and burn it instantly. If the original head failed because of an internal short, the board channel may already be damaged too.

Prevention

  • Have a technician test heads with suitable instruments before connection, especially used or refurbished heads.
  • Buy heads from reputable suppliers who guarantee condition.
  • Inspect head cables and connectors for damage or ink before installation.

Cause 4: Wrong voltage or waveform settings

Ricoh heads need correct drive settings for reliable jetting. Each head has recommended settings that the technician enters in the software, based on the head’s data and the ink manufacturer’s guidance. Using settings from the old head, default settings or wrong values can overdrive the head and stress the driver circuit. In some systems, wrong settings cause the head to draw abnormal current or overheat.

Prevention

  • Record the new head’s data before installation.
  • Enter correct settings in the software before the first firing.
  • Follow the supplier’s guidance for your board system, head and ink.
  • Double-check settings on the screen before running a nozzle check.

Cause 5: Ink and fluid in connectors

During a head change, ink and cleaning fluid are everywhere. Drips on the connector or cable end can create leakage paths between pins or corrode contacts. UV ink that is not cleaned off will remain liquid until stray light cures it.

Prevention

  • Cover connectors while handling ink lines.
  • Keep cable ends dry and clean.
  • Wipe away any ink near connectors before power-on.
  • Allow cleaning fluid to dry fully before powering on.

Cause 6: Static discharge during handling

Handling heads and boards without anti-static precautions can damage sensitive components, especially in dry winter conditions. Static damage may not be immediately visible but can cause failures later.

Prevention

  • Wear an earthed anti-static wrist strap.
  • Keep heads in their anti-static packaging until installation.
  • Avoid touching connector pins and board components.

Signs of a burnt Ricoh head board

  • The new head does not fire at all.
  • A neighbouring head on the same adapter board also stops.
  • Burning smell or visible discolouration near the connector or driver components.
  • Software errors indicating head faults or abnormal values.
  • The head board or adapter board becomes unusually hot.

If any of these appear, switch off immediately. Do not try another head on the same channel until the channel has been tested.

What to do after a burnt head board

  1. Switch off and stop. Do not try repeated power cycles or other heads.
  2. Document. Photograph the board, connectors and cable ends, and note settings and events.
  3. Test the head. Have a technician check it for shorts.
  4. Test the board channel. Have the technician check the driver section and connectors.
  5. Identify the root cause. Hot-plugging, insertion, shorted head, settings or contamination.
  6. Repair or replace. Repair the board channel or replace the board, and replace the head if damaged.
  7. Prevent recurrence. Update procedures and train staff.

Our UV carriage board replacement checklist covers the replacement process in detail.

Safe Ricoh head change procedure

  1. Prepare the new head, settings data, tools, absorbent pads and anti-static wrist strap.
  2. Back up current settings.
  3. Switch off and unplug the machine; isolate lamps and chiller.
  4. Close ink valves to the head being changed.
  5. Disconnect the old head’s cable, releasing locking tabs and pulling straight.
  6. Remove the old head and clean the mounting area.
  7. Test the new head for shorts if possible.
  8. Install the new head mechanically, keeping it level and secure.
  9. Connect the cable straight and fully, in the correct orientation, and close the locking tab.
  10. Connect ink lines and check for leaks without power.
  11. Power on and enter correct head settings before firing.
  12. Check head temperature rises normally.
  13. Fill ink, purge gently and run a nozzle check.
  14. Align and calibrate the new head.

Head change risk checklist

RiskPrevention
Hot-pluggingPower off and unplug, always
Angled or reversed cableCheck orientation, insert straight, lock tab
Shorted headTest before connection, buy from reliable suppliers
Wrong settingsEnter correct settings before first firing
Ink in connectorKeep connectors covered and dry
StaticWrist strap, anti-static packaging
Damaged board channelTest channel before fitting new head after a failure

The cost of getting it wrong

A single mistake during a head change can cost a new Ricoh head, a head board or adapter board, and days of downtime. With Ricoh Gen5 heads at around ₹1.25 lakh to ₹1.55 lakh from Indian traders, and Ricoh Gen5 head and carriage boards listed from about $287 to $650 on Chinese marketplaces before shipping, duty and GST, the cost of a burnt board and head together can easily exceed ₹2 lakh. Following procedures carefully is far cheaper. For head prices, see our guide to Ricoh Gen5i printhead prices in India.

Example: hot-plugging during a rush job

A unit in Patna was rushing to finish an election banner order when one head failed. The operator swapped in a spare head without switching off the machine, to save time. The new head did not work, and the adapter board channel was damaged. The unit lost a day waiting for a technician and paid for both a new head and an adapter board repair. A written power-off rule and a simple head change checklist were introduced afterwards.

Example: a used head with a hidden short

Another unit bought a used Ricoh Gen5 head at a low price. On connection, the head board channel burnt instantly. Testing showed the head had an internal short from previous ink ingress. Since then, the unit tests all used heads before connection and buys only from suppliers who guarantee condition.

Why Ricoh head changes are higher risk on UV machines

Head changes are risky on any piezo-head printer, but several factors make them especially sensitive on UV roll to roll machines:

  • Heated heads: Ricoh heads include heaters controlled through the head board. Heater connections carry more current than data lines, so a misaligned connection can cause heat damage quickly.
  • UV ink residue: ink around connectors stays liquid until cured, so contamination is more likely during a messy head change.
  • Two-colour heads: a Ricoh Gen5 MH5420 head may carry two colours, so a damaged channel can take out two colours at once.
  • Lamps on the carriage: lamps must be isolated during the job; accidental lamp activation during testing can cure ink on the new head’s nozzle plate.
  • Static from media: machines printing film and vinyl are more exposed to static, which affects both head and board during handling.

Testing a channel after a failure

If a head failed or a board channel is suspected, never fit a new head until the channel has been checked. A technician can:

  1. Inspect the connector and driver components visually for discolouration, cracks or burnt smell.
  2. Measure supply voltages on the board with heads disconnected.
  3. Use the board system’s diagnostic tools, if available, to check channel status.
  4. Test the channel with a known good test head or test load, if the workshop has one.
  5. Compare readings with a known good channel on the same board.

Only when the channel tests normal should a new head be connected. If the channel is damaged, repair or replace the board first.

Buying heads safely

Ricoh heads are expensive, and the market includes new, refurbished, grey-market and used heads. To reduce risk:

CheckWhy
Buy from established suppliers with a physical address and GST registrationRecourse if something goes wrong
Ask whether the head is new, refurbished or usedCondition affects risk and price
Check packaging, labels and cable condition on arrivalDamage or tampering suggests risk
Ask for the head’s data, such as recommended drive settingsNeeded for correct setup
Confirm the warranty and what voids itMany warranties exclude installation damage
Confirm the exact model: Gen5, Gen5i, Gen6 and variantWrong variant may not work with your board

Unified Engineering Dynamics supplies the Ricoh Gen5 printhead with compatibility and installation guidance. For background on head types, see our comparison of Ricoh Gen5i, Konica KM1024i and Starfire heads.

Head storage before installation

New heads should be stored in their original packaging, at moderate temperature, away from direct sunlight and UV light, and protected from static and physical shock. Do not remove protective caps until installation. If a head has been filled with ink, follow the supplier’s guidance on storage and flushing, because UV ink left in a head exposed to light can cure inside the nozzles.

Training and responsibility

Most burnt boards after head changes are caused by procedural mistakes, often under time pressure. Assign head changes only to trained staff, keep a printed head change checklist at the machine, and require a second person to check cable orientation and settings before power-on. In busy seasons, resist the urge to rush. A careful head change that takes an extra half hour is far cheaper than a burnt board and head.

What a technician will check when called after a failure

  • Visual inspection of the head, cable, connector and board.
  • Electrical tests on the head for shorts.
  • Voltage checks on the board with heads disconnected.
  • Review of software settings entered for the new head.
  • Questions about the procedure followed and any unusual events.

Answering honestly helps the technician find the root cause quickly and prevents a repeat.

Signs that a head was faulty before installation

Sometimes a head is damaged before it ever reaches the machine. Warning signs include damaged or dented packaging, a cable that is creased or kinked, ink residue on a supposedly new head, missing protective caps, labels that look altered, or a nozzle plate with visible scratches. If you notice any of these, do not install the head. Photograph it, contact the supplier, and ask for a replacement or testing. Installing a suspect head risks both the head board and your warranty claim, because suppliers may argue the damage occurred during installation.

Recording each head change

Keep a record of every head change: date, head position, head serial number, supplier, settings entered, technician and any problems. If a board channel later fails, the record helps identify whether one position, one supplier or one procedure is linked to repeated failures. It also supports warranty claims for both heads and boards.

Using a test load before fitting expensive heads

Some workshops keep an old but electrically healthy head, or a dedicated test fixture, to check a channel before fitting a new head. Connecting the test head first, with power off, then powering on and checking for normal behaviour, confirms that the channel is safe. This simple step can save a new Ricoh head worth more than a lakh of rupees.

Further reading: Ricoh heads jet ink using piezoelectric actuators, which need a precisely controlled drive voltage.

Key takeaways

  • A burnt Ricoh head board after a head change is usually caused by hot-plugging, wrong cable insertion, a shorted head, wrong settings, contamination or static.
  • Always switch off and unplug before handling heads and cables.
  • Test heads before connection, especially used or refurbished heads.
  • Enter correct settings before the first firing.
  • After a failure, test both head and channel before fitting another head.

More in the UV carriage board series

Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.

Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine head carriage board and the eco-solvent head carriage board.

Frequently Asked Questions

Why did my head board burn after changing a Ricoh head?

The most common causes are hot-plugging, angled or reversed cable insertion, a head with an internal short, wrong voltage or waveform settings, ink in the connector and static discharge.

Can a new Ricoh head damage the head board?

Yes, if it has an internal short or is connected incorrectly. Test heads before connection and follow correct procedures.

Is hot-plugging really that dangerous?

Yes. During insertion, contacts connect at different times, which can send voltage to the wrong pins and damage the head and board instantly.

Can I try another head on the same channel after a failure?

Not until the channel has been tested. A damaged channel can destroy another head.

How do I set the voltage for a new Ricoh head?

Use the head’s data and your board supplier’s and ink manufacturer’s guidance, and enter correct settings in the software before the first firing.

Can a burnt head board be repaired?

Often yes, if damage is limited to driver components or connectors. A technician can evaluate the board.

Should I buy used Ricoh heads?

Used heads carry more risk of hidden faults. Test them before connection and buy only from suppliers who guarantee condition.

Does ink in the connector cause damage?

Yes. Ink and cleaning fluid can create leakage paths between pins and corrode contacts. Keep connectors clean and dry.

Do I need an anti-static wrist strap for head changes?

Yes. Static can damage head and board electronics, especially in dry conditions. Use an earthed wrist strap.

What are the signs of a burnt head board?

The new head does not fire, a neighbouring head also stops, a burning smell or discolouration appears, or the board becomes unusually hot.

How much does a burnt head board cost to fix?

Costs vary. Board repair may be modest, but replacing both a head and a board can exceed ₹2 lakh including a Ricoh Gen5 head.

Who should change Ricoh heads?

Trained technicians who follow strict power-off, testing and settings procedures. Unified Engineering Dynamics can help with head changes and board repairs.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *