Direct answer: The most common UV head board failure symptoms on a roll to roll printer are a head or pair of heads missing completely from the nozzle check, “head not detected” or head communication errors, head temperature errors, random nozzles dropping out across several heads, and faults that appear only after the machine warms up. Each of these can also be caused by the printhead, flat cables, ink supply, negative pressure or software settings, so a careful isolation routine is essential before you replace an expensive board.
Recognising true UV head board failure, and ruling out ink, cable and static look-alikes, prevents expensive and unnecessary board and head purchases.

Table of Contents
When a UV roll to roll printer starts dropping heads or showing errors, the pressure to get back into production is intense. It is tempting to order the first part someone suggests. This guide explains what a real UV head board failure looks like on machines with Ricoh Gen5, Gen5i, Gen6, Konica KM1024i, Kyocera and Epson i3200-U1 heads, which faults imitate it, and how to narrow down the cause with simple, safe tests. It follows on from our explanation of what the UV roll to roll carriage board does.
Why diagnosis needs care on UV machines
On a UV roll to roll printer, the head board (or carriage board) sits in a chain of parts: PC and print software, mainboard, data link, carriage board, adapter boards, flat cables, and finally the printheads. On top of that electrical chain sit the ink system, the negative pressure system, white ink circulation, head heaters and UV lamps. A fault anywhere in these systems can produce a symptom that looks like a head board failure.
The costs of guessing wrong are high. A Ricoh Gen5 head costs around ₹1.25 lakh to ₹1.55 lakh from Indian traders, and carriage boards and board kits cost tens of thousands of rupees. Fitting a new head to a faulty driver channel can damage the new head. Fitting a new board when the real fault is a cracked cable wastes money and leaves the problem unsolved. Methodical diagnosis protects both your budget and your parts.
Symptom 1: One head completely missing
A single head prints nothing in the nozzle check, while all other heads print normally.
Possible causes
- The head’s flat cable is loose, cracked or inserted at an angle.
- The adapter board for that head has failed.
- The channel on the carriage board’s driver section has failed.
- The head itself has failed electrically.
- Ink is not reaching the head because of an empty sub-tank, a closed valve, a blocked filter or an air lock.
- The head is disabled or mapped incorrectly in the software.
How to narrow it down
First check ink supply: is the sub-tank filled, the valve open, and does ink appear when you perform a gentle purge? If ink flows but nothing prints, the problem is electrical. Then, with power off, reseat the flat cable at both ends. If the head still does not fire, a technician can swap that head’s cable to a neighbouring channel. If the fault moves with the head, the head or its cable is likely faulty; if the fault stays with the channel, the adapter board or carriage board is suspect.
Symptom 2: Two heads on the same adapter board missing
On many Ricoh systems, adapter boards serve two heads. When both heads connected to one adapter stop together, the shared parts become the main suspects: the adapter board itself, its connection to the carriage board, or the carriage board channel that feeds it. Two heads failing simultaneously because of two separate head faults is much less likely, unless a power event damaged both.
Check whether both heads share an ink supply, as a shared ink problem could also explain both missing. If ink is fine, inspect the adapter board for damage, ink contamination or a loose connector.
Symptom 3: Head not detected or head communication errors
The software reports that one or more heads are not detected, or shows communication errors, sometimes intermittently.
Possible causes
- Loose or damaged flat cable or data cable.
- Hardened ink or corrosion on connector pins.
- Failing adapter board or carriage board.
- A failed head that no longer responds.
- Problems in the data link between the mainboard and carriage board.
- Interference from lamp power cables running too close to data cables.
If the error affects all heads at once, look upstream at the data link from the mainboard, the mainboard itself or the power supply to the carriage. Our article comparing head data cable and carriage board faults explains how to separate these causes.
Symptom 4: Head temperature errors
UV inks need heating to reach the correct viscosity for jetting. Ricoh and Konica industrial heads have built-in heaters and thermistors controlled through the head board. Temperature-related symptoms include:
- A head that never reaches its set temperature.
- A head that shows an impossible reading, such as zero or a very high value.
- Heating errors that appear only on cold mornings.
- One head heating much slower than the others.
Possible causes
The heater or thermistor inside the head may have failed, the heater circuit on the head board may be faulty, a cable conductor carrying the heater or sensor signal may be broken, or the temperature setting may be wrong. Swapping head positions helps: if the error follows the head, suspect the head’s internal heater or sensor; if it stays with the position, suspect the board or cable. Note that heaters draw more current than data lines, so a weak connection here may show signs of heat discolouration.
Symptom 5: Random nozzles dropping across several heads
Nozzles disappear randomly across several heads, rather than a clean block or a single head failing. This symptom is usually not a head board fault. More common causes include:
- Air in the ink system or unstable negative pressure.
- Ink that is too cold and therefore too thick.
- Partially cured ink on the nozzle plate from stray UV light.
- White ink settling because circulation has stopped.
- Static discharge from film media disturbing the jetting.
- Head height set too high, creating mist and satellite drops.
However, if nozzles drop out in a pattern that matches one adapter board or the timing of the carriage reaching one end of travel, a weak connection or cracked cable that opens with movement may be the cause. Watch the pattern carefully. Our guide on white ink circulation engineering covers the white ink causes.
Symptom 6: Faults that appear after warming up
The machine prints perfectly for thirty minutes to an hour, then heads begin dropping out or errors appear. Turning the machine off for a while seems to fix it temporarily.
Heat-related intermittent faults often point to a failing component on a board, such as a capacitor or regulator, or to a solder joint or connector that opens when it expands. On UV machines, the lamps add heat to the carriage, so check lamp cooling first. A clogged lamp fan, a chiller low on coolant, or a hot room can push carriage temperatures beyond what the electronics can handle. If cooling is fine and the fault persists, a technician can use gentle cooling spray or a hot-air tool to locate the heat-sensitive component.
Symptom 7: Ink spray, ghost images or uncontrolled firing
Ink sprays from a head in random patterns, or the head fires when it should not. This is a serious symptom that can indicate a driver section fault on the head board, a damaged head, or static discharge disturbing the signals. Stop printing immediately, as uncontrolled firing can flood the carriage with ink, damage heads, and further damage the board. Check earthing and static control before restarting.
Symptom 8: Visible damage, smell or smoke
A burning smell, discoloured components, cracked chips or melted connectors are clear signs of electrical damage. Switch off immediately and do not power on again until the board has been inspected. Common causes include a head with an internal short, hot-plugging a head or cable, ink entering a connector, or a power surge. Before fitting a new board, the root cause must be found; otherwise the new board may fail in the same way. See our article on burnt Ricoh head boards after a head change.
Look-alike faults: UV head board failure or something else?
| Symptom | Board possible? | More common causes to check first |
|---|---|---|
| One head missing | Yes | Ink supply, flat cable, software mapping |
| Two heads on one adapter missing | Likely | Adapter board, connector |
| All heads missing | Less likely | Data link, mainboard, carriage power supply |
| Head temperature error | Possible | Head heater or thermistor, cable, settings |
| Random nozzles across heads | Unlikely | Air, negative pressure, ink temperature, cured ink on nozzle plate, static |
| Faults after warm-up | Possible | Lamp cooling, room temperature, connectors |
| Uncontrolled firing | Possible | Static, damaged head, settings |
| Burning smell or visible damage | Yes | Find root cause: head short, ink ingress, surge |
A step-by-step isolation routine
Use this routine whenever you suspect a head board problem. Steps involving connectors should be done only with the machine switched off and unplugged.
- Record the symptom. Print a nozzle check, photograph it, and note error messages, time of day, media and how long the machine had been running.
- Check ink supply. Confirm sub-tanks are filled, valves are open, filters are clear and negative pressure is stable.
- Check temperatures. Confirm head temperatures reach their set points and that lamp cooling is working.
- Check software settings. Confirm heads are enabled, mapped correctly and have the correct voltage and waveform settings for your head and ink.
- Inspect cables and connectors. Look for cracks, twists, ink deposits and loose connections. Reseat connectors carefully.
- Swap test. Exchange the cable or position of the suspect head with a known good one, following your technician’s guidance.
- Inspect the board. Look for discolouration, swollen capacitors, ink contamination or corrosion.
- Decide. Repair or replace only the part that the tests have pointed to, and fix the root cause.
Information to collect before calling a technician
- Machine brand, model and width.
- Head type and number of heads, including white and varnish channels.
- Board system and version, with photos of the boards.
- Software name and version.
- Photos of nozzle checks before and after the fault started.
- Any recent events: head change, storm, power cut, ink change, media change or relocation.
With this information, a technician can often suggest likely causes over the phone and bring the right parts on the first visit.
Common mistakes
- Replacing the head board because one head is missing, without checking ink and cables first.
- Fitting a new head to a channel that just burnt a head, without testing the channel.
- Connecting or disconnecting heads with power on.
- Ignoring lamp cooling and blaming heat-related faults on boards.
- Cleaning connectors with excess fluid, which leaves residue behind.
- Removing anti-static brushes and forgetting to refit them.
Example: a missing head that was an ink problem
A unit in Kanpur reported that the cyan head on their Ricoh Gen5 roll to roll printer had stopped completely overnight. The operator suspected the head board. The technician found that the cyan sub-tank float sensor had stuck, the sub-tank had emptied, and air had entered the head. After freeing the sensor, refilling and purging, the head printed normally. No electrical parts were needed.
Example: an adapter board with hardened ink
In another case, a pair of heads on one adapter board kept showing intermittent communication errors. Inspection found a thin layer of partially cured ink on the adapter board connector, caused by a slow drip from a damper above. The connector was cleaned carefully, the damper was replaced, and a small shield was added to keep drips away from the board. The errors stopped. This illustrates how UV ink residue, which does not evaporate, can gradually cause electrical faults.
Preventing head board failures
The best way to avoid these symptoms is prevention:
- Keep lamp cooling working and the room ventilated.
- Fix ink leaks above the carriage immediately.
- Maintain good earthing and static control, especially when printing film media.
- Route cables carefully in the cable chain and replace worn ones.
- Always switch off before touching heads, cables or boards.
- Use a stabilizer and surge protection appropriate for the machine’s load.
Our full guide to UV carriage board damage from lamp heat and ink mist covers prevention in detail.
Machine-specific notes: Ricoh, Konica, Kyocera and Epson heads
Symptoms differ slightly with the head type fitted to your UV roll to roll printer:
| Head type | What to watch for |
|---|---|
| Ricoh Gen5 / Gen5i | Two-colour heads mean one failed channel can remove two colours; heater and thermistor errors are common clues |
| Ricoh Gen6 | Faster firing makes waveform and voltage settings critical; confirm settings before blaming the board |
| Konica KM1024i | Head boards often serve several heads; group failures point to the shared board or cable |
| Kyocera | Usually on high-end machines with specific board systems; follow the manufacturer’s diagnostic routine |
| Epson i3200-U1 | Smaller machines on Hoson or Senyang boards; cable and ink faults are very common look-alikes |
Whatever the head, the logic is the same: find out whether the fault follows the head, the cable or the board channel, and fix the root cause before fitting new parts.
Keep a fault log
A simple notebook or spreadsheet beside the machine makes diagnosis far easier. Record the date, symptom, nozzle check photo, media, room temperature, what was checked and what fixed it. After a few months, patterns appear: faults that come on hot afternoons, with a particular film, or after a particular operator’s shift. Those patterns point to the real cause much faster than guesswork, and they help your technician when a fault does need a board repair.
Further reading: The isolation routine above follows standard troubleshooting practice: test the simplest, most likely causes first.
Key takeaways
- UV head board failure symptoms include missing heads, communication errors, temperature errors, faults after warm-up and visible damage.
- Random nozzle loss across several heads is usually an ink, temperature, air or static problem rather than a board fault.
- Use swap tests, with power off, to see whether a fault follows the head or stays with the channel.
- Always find the root cause before fitting a new head or board.
- Lamp cooling, leak control, earthing and careful cable handling prevent most failures.
More in the UV carriage board series
- UV Roll to Roll Head Carriage Board Explained
- Hoson vs Senyang vs BYHX Carriage Boards for Ricoh Gen5/Gen6
- Adding White and Varnish: Head and Carriage Board Upgrade
- UV Lamp Heat, Ink Mist and Carriage Board Damage
- Head Data Cable vs Carriage Board Fault
- UV Carriage Board Replacement Checklist
- Burnt Head Board After a Ricoh Head Change
- UV Roll to Roll Carriage Board Price in India
- UV Carriage Board Connectors, Pins and Static
Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.
Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine head carriage board and the eco-solvent head carriage board.
Frequently Asked Questions
What are the signs of a bad head board on a UV printer?
Common signs include one or two heads missing completely, head not detected or communication errors, head temperature errors, faults that appear after warm-up, uncontrolled firing and visible damage or burning smell.
Can a bad head board cause random missing nozzles?
It can, but random missing nozzles across several heads are more often caused by air in the ink system, unstable negative pressure, cold ink, cured ink on the nozzle plate or static from film media.
How do I know if the head or the head board is faulty?
With power off, swap the suspect head’s cable or position with a known good one. If the fault follows the head, suspect the head; if it stays with the channel, suspect the cable, adapter board or head board.
Why does my UV printer lose heads only after it warms up?
Heat-related faults often come from poor lamp cooling, high room temperature, or a failing board component or connector that opens when hot. Check lamp fans and the chiller first.
What causes head temperature errors on Ricoh heads?
A failed heater or thermistor inside the head, a faulty heater circuit on the head board, a broken cable conductor or incorrect temperature settings.
Is it safe to keep printing with one head missing?
You can sometimes print in a reduced mode, but find the cause quickly. If the fault is electrical, continued operation may cause further damage, especially if there is any burning smell.
Can UV ink damage the head board?
Yes. UV ink does not evaporate, so drips and mist can stay on connectors and boards, partly cure, attract dust and cause poor contacts or leakage between pins.
Should I replace the head board if all heads stop working?
Not straight away. When all heads stop, check the data link from the mainboard, the carriage power supply and the mainboard before suspecting the carriage board.
Can static cause head board failures?
Yes. Film and vinyl media can create strong static charges. Without good earthing and anti-static brushes, discharges can disturb jetting and damage head driver circuits over time.
What information should I give my technician?
Machine model, head type and count, board system and version, software version, nozzle check photos and any recent events such as head changes, storms or ink changes.
How much does a Ricoh Gen5 head cost in India?
IndiaMART traders list Ricoh Gen5 heads at around ₹1.25 lakh to ₹1.55 lakh in late 2026, which is why diagnosis before replacement is so important.
Can a cracked flat cable look like a head board fault?
Yes. A cracked cable can cause missing heads or intermittent errors that come and go with carriage movement, which is easy to mistake for a board failure.