Flex Printing

Flex Board Compatibility Table: Konica 512i, 1024i, Ricoh and Starfire Heads with BYHX, Hoson, Senyang and UMC Boards

Flex Board Compatibility Table: Konica 512i, 1024i & Boards

Direct answer: A flex board compatibility table links each printhead to the board systems, cables, firmware and software it works with. In short: Konica KM512i heads run on KM512-specific boards from BYHX, Hoson, Senyang or UMC; Konica KM1024i heads need 1024-specific head boards, cables and usually a matched main board; Ricoh Gen5 heads need Ricoh boards; Starfire 1024 heads need Starfire-specific boards; and Seiko heads need Seiko boards. Board systems never mix: the main board, head carriage board and driver boards must all come from the same system, with compatible versions, the right head count (4 or 8 heads) and matching firmware and software. Always confirm with the supplier in writing using photos of your labels.

Use this flex board compatibility table before buying any head, board, cable or upgrade kit, because mismatches are expensive.

Flex Board Compatibility Table: Konica 512i, 1024i & Boards
Flex Board Compatibility Table: Konica 512i, 1024i & Boards

Compatibility mistakes are among the costliest in flex printing: a board that will not communicate, a cable that burns a head board, or an upgrade that stalls because the software licence does not cover the new heads. This guide brings the compatibility rules from our flex printer electronics series into reference tables. Use them as a starting point, then confirm details with your supplier.

Flex board compatibility table: head to board system

PrintheadCommon board systemsNotes
Konica KM512i (LNB, MHB, LHB variants)BYHX, Hoson, Senyang, UMCMost common flex configuration in India; match drop size settings
Konica KM512 (older, non-i)Older BYHX, UMC and othersCheck that boards support the older head; spares getting scarcer
Konica KM1024iBYHX and other 1024-capable systemsNeeds 1024 head boards, cables, firmware and software
Ricoh Gen5Ricoh-specific BYHX, Hoson and othersSeen on some solvent and hybrid machines
Starfire 1024Starfire-specific boardsStarfire main boards listed around $650โ€“668
Seiko 510/1020Seiko-specific boards, often maker’s ownUsed on older solvent machines

See head driver board compatibility and carriage board systems for Konica.

Board to board rules

RuleWhy it matters
Main, carriage and driver boards from the same systemDifferent protocols, firmware and connectors
Compatible versionsVersion mismatch causes “board not found” or recognition errors
Matching head countA 4-head board cannot drive 8 heads
Cables matched to board revisionPinouts and lengths can differ between revisions
Power supplies matched to boardsWrong voltage destroys boards and heads

See 4-head vs 8-head carriage board upgrades.

Board system to software and RIP

ItemCompatibility rule
Print control softwareSupplied with the board system; version must match firmware
Licence or dongleMay be tied to the main board or a USB dongle
RIP (PhotoPrint, Maintop, Onyx and others)Must support the printer model and board system
Colour profilesSpecific to ink, media, mode and head type; rebuild after major changes

Head to ink

RuleDetail
Use solvent ink approved for the headAsk the ink maker for head approval and recommended settings
Match temperature to the ink data sheetViscosity changes with temperature
Match waveform to head and inkWrong waveform causes satellites, weak drops or misfiring
Flush properly when changing ink brandMixing incompatible inks can gel or clog heads
Do not run eco-solvent and solvent in the same head without full flushingDifferent chemistry and settings

See eco-solvent vs solvent flex printers.

Head variants and settings

Head familyVariant differencesCompatibility impact
KM512i LNB / MHB / LHBDifferent drop sizes (about 14, 30 and 42 pl)Different waveforms, voltages and profiles
KM512 vs KM512iOlder and newer generationsBoard support and settings may differ
KM512i vs KM1024i1024 has twice the nozzles per headNew head boards, cables, firmware and profiles

See Konica 512i head voltage settings.

Cables and connectors

Head data cables look similar across systems but differ in length, pin count, shielding and pinout. Using the wrong cable can damage boards and heads. Replace cables with the type specified for your board system and head, and check orientation marks. KM1024i heads use different cables from KM512i heads. Fibre links, where fitted, must match the transceivers on both boards. See data and printhead cable compatibility.

Power supplies

Each board needs specific voltages and current capacity. A replacement power supply must match output voltages, current rating, connectors and mounting. A higher current rating at the correct voltage is usually acceptable; a different voltage never is. See power supplies for flex printers.

Heater and dryer compatibility

Heater elements, thermocouples, controllers and relays must match the machine’s voltage, wattage and sensor type. A thermocouple of the wrong type gives false readings, leading to overheated media or poor drying. Replace like for like and check the controller’s sensor setting.

Firmware and software versions

Within a board system, firmware on main, carriage and sometimes driver boards must match each other and the print software. When replacing one board, the supplier may need to update the others. Record all versions and follow the supplier’s update sequence. See our firmware update guide.

Upgrade compatibility

UpgradeWhat usually changes
KM512i to KM1024iHead boards, cables, main board or firmware, software, waveforms, profiles
4 heads to 8 headsCarriage board capacity, cables, ink system, software licence
Changing ink brandWaveforms, temperatures, profiles, flushing
Changing RIPPrinter driver support, profiles, workflows
Changing board systemAlmost all electronics and software

The typical 1024 kit was listed at $1,000โ€“1,420 from China. See our 512i to 1024i upgrade guide.

Used and refurbished parts

Used boards can be good value but carry extra compatibility risk: older versions, unknown firmware, modifications and missing accessories. Ask for photos of labels and version stickers, test evidence and written return terms, and test the part as soon as it arrives.

Questions to ask suppliers

  • Is this part compatible with my board system, version and head count?
  • Will firmware on other boards need updating?
  • Does it need different cables or adapters?
  • Will my software licence or dongle still work?
  • Are voltages or waveforms different?
  • What warranty applies, and what voids it?
  • Can you confirm compatibility in writing?

Quick reference by part type

Buying aโ€ฆConfirm
Konica headModel, variant, drop size, board support, waveform, ink approval
Head carriage boardSystem, version, head type and count, firmware, cables
Driver boardSystem, version, head type, firmware
Main boardSystem, version, head support, firmware, software, licence, ports
CableSystem, head type, length, pin count, revision
Power supplyVoltages, current, connectors, mounting
Heater partVoltage, wattage, sensor type, mounting
RIPPrinter and board support, version, licence

Recording your machine’s compatibility profile

Create a one-page profile for each machine listing the model and width, board system and versions, firmware, software and licence, RIP version, head types, serials, positions and label voltages, ink brand, heater controller and sensor types, power supply types and cable types. Update it after every change. With this profile, checking any new part takes minutes.

Compatibility in the Indian market

Most flex machines in India are imported from China with BYHX, Hoson, Senyang or UMC electronics and Konica 512i heads. Traders in Delhi, Mumbai, Lucknow and other cities stock common boards for these configurations; for example, BYHX 512i kits were listed around โ‚น75,000โ€“76,000 and UMC kits around โ‚น40,000โ€“85,000 depending on contents. Less common configurations may need imports taking one to three weeks. Standard configurations make long-term ownership easier.

Example: board version mismatch

A unit bought a replacement BYHX head board from the correct system but a newer version. The main board did not recognise it until its firmware was updated. The supplier sent the files and the correct sequence, and the machine was back in production the same day.

Example: wrong cable after upgrade

Another shop upgraded to 1024i heads but reused the old 512i cables. The heads were not detected, and one adapter was damaged. Fitting the correct 1024 cables solved the problem; checking the kit contents beforehand would have avoided the damage.

Compatibility over the machine’s life

Over a flex machine’s working life of eight to twelve years, board versions, firmware, software and ink formulations all change. The boards available today may differ from those fitted when your machine was new, even from the same maker. Keep your machine profile current, ask suppliers about long-term availability of your board versions, and consider buying key spares while compatible versions are still easy to find. When a part is discontinued, suppliers often offer an upgrade kit that replaces several boards together. Plan such upgrades during a quiet season rather than waiting for a failure in the middle of an election rush.

Compatibility and print applications

The application also affects the right combination. Large outdoor hoardings printed at speed on frontlit flex suit KM512i heads with larger drop sizes, while backlit flex, vinyl and closer-viewing work benefit from smaller drops or 1024i heads. Changing applications may therefore mean changing head variants, waveforms, profiles and sometimes boards. Test the complete combination of head, ink, media and RIP settings, and build profiles before taking orders in a new segment.

Example: an 8-head expansion that needed a licence

A shop in Kanpur wanted to expand a 4-head Konica machine to 8 heads to double output. The carriage board supported 8 heads, and the supplier sent the correct cables. However, the print software licence covered only 4 heads, and the ink system needed four more dampers and sub-tanks. After the licence was upgraded and the ink system completed, the expansion worked well. Checking every compatibility point beforehand saved them from buying parts that would have sat unused.

Example: changing ink brand

Another unit switched to a cheaper solvent ink without asking the ink maker about head approval or settings. Nozzles dropped out more often and colours shifted. After flushing properly, setting the temperature and waveform recommended for the new ink and rebuilding profiles, quality returned. The lesson: ink is part of the compatibility chain, not just a consumable.

Why written confirmation matters

Verbal assurances such as “it will work” are easy to give and hard to enforce. A short written confirmation listing your machine, board system, versions and the part being supplied protects both you and the supplier. If the part turns out to be incompatible, the confirmation makes a return or exchange straightforward. Good suppliers are happy to provide it, and their willingness to do so is itself a sign of reliability.

Compatibility of motion electronics

Servo and stepper drivers, motors, encoder readers and sensors also have compatibility rules. A replacement servo driver must match the motor type, power rating, encoder feedback and control signals from the main board, and often needs parameters copied from the old driver. Encoder strips and readers must match in resolution; a strip with the wrong lines per inch will cause position errors and banding that no amount of head adjustment can fix. Sensors must match voltage, type (NPN or PNP) and mounting. Record motion part numbers in your machine profile alongside the boards and heads, so a motion failure is as quick to resolve as a board failure.

Compatibility checks after any repair

After a board repair or replacement, run a short compatibility check before returning to production: confirm the software recognises every board and head, read back firmware versions and compare them with your profile, check that each head’s voltage and temperature settings survived, print a nozzle check and a colour test, and run a long job to confirm stability. Recording these results also gives you evidence if the replacement part later develops a fault under warranty.

Bottom line

A flex board compatibility table is only as useful as the information you keep. Maintain an up-to-date machine profile, check every new part against heads, boards, firmware, software, RIP, ink, cables, power supplies and heaters, and get written confirmation from suppliers. That avoids the most expensive mistakes in flex machine repair and upgrades.

Further reading: Each board runs its own firmware, and versions must stay compatible across the system.

Key takeaways

  • A flex board compatibility table links heads, boards, cables, firmware, software and ink.
  • Board systems never mix; versions, head counts and cables must match.
  • KM1024i upgrades need new head boards, cables, firmware and profiles.
  • Ink must be approved for the head, with correct temperature and waveform.
  • Always get written confirmation from suppliers.

More in the flex electronics planning series

Related reading on our site: Konica KM512i printhead price and lifespan, KM512i vs KM1024i printheads, flex printer mainboard and head board buyer checks, data and printhead cable handling and the flex printing machine maintenance checklist.

Running an Epson-head eco-solvent machine as well? Our sister series starts with the eco-solvent head carriage board guide and the complete guide to eco-solvent printer electronics.

Frequently Asked Questions

Which boards work with Konica 512i heads?

KM512-specific boards from systems such as BYHX, Hoson, Senyang and UMC. Check version and head count.

Can I use 512i head boards with 1024i heads?

No. 1024i heads need 1024-specific head boards, cables, firmware and software.

Can I mix BYHX and Hoson boards?

No. Main, carriage and driver boards must come from the same system.

Are head data cables interchangeable?

No. Cables differ in length, pin count, shielding and pinout between systems and head types.

Do different 512i variants need different settings?

Yes. LNB, MHB and LHB variants have different drop sizes and need matching waveforms, voltages and profiles.

Does my RIP work with any board system?

Not necessarily. Check that your RIP supports your printer model and board system.

Will my software licence work after a main board change?

It depends on whether the licence is tied to the board or a dongle. Ask the supplier before replacing.

Can I change ink brand without changing settings?

No. Waveforms, temperatures and profiles usually need adjusting, and the heads must be flushed properly.

Can I upgrade from 4 to 8 heads?

Only if the carriage board, cables, ink system and software licence support 8 heads.

Are used boards compatible?

They can be, but check versions, firmware, modifications and return terms, and test on arrival.

How much does a 1024 upgrade kit cost?

Chinese listings showed 1024 kits at about $1,000โ€“1,420, before shipping, duty and GST.

Does heater sensor type matter?

Yes. The wrong thermocouple type gives false readings and causes overheating or poor drying.

How do I confirm compatibility before buying?

Send photos of labels, version details, head information and software versions to the supplier and get written confirmation.

Can Unified Engineering Dynamics check compatibility?

Yes. Send details and photos and our team will help confirm compatible boards, heads and parts.

Do board versions change over a machine’s life?

Yes. Versions, firmware and software change. Keep your profile current and plan upgrades when parts are discontinued.

Why ask for written compatibility confirmation?

It protects you if a part proves incompatible and makes returns or exchanges straightforward.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *