UV Printing

UV Flatbed Driver Board vs Main Board vs Head Board: Which Board Does What

UV Flatbed Driver Board vs Main Board vs Head Board Explained

Direct answer: In the UV flatbed driver board vs main board question, the difference is location and job. The main board sits in the electronics cabinet and is the machine’s brain: it talks to the RIP PC, drives the X, Y and Z motors, reads the encoder, limit switches and vacuum controls, switches the UV lamps and streams print data to the carriage. The head board, or carriage board, rides on the carriage and distributes that data to each printhead, controls head heating and reads carriage sensors. The driver board, built into the head board on most Epson-head flatbeds and separate on many Ricoh machines, creates the high-voltage firing pulses for each nozzle. Knowing which board does what tells you where to look when something fails.

Settling the UV flatbed driver board vs main board question tells you exactly where to look when a fault appears, and which board to order.

UV Flatbed Driver Board vs Main Board vs Head Board Explained
UV Flatbed Driver Board vs Main Board vs Head Board Explained

Flatbed owners hear many board names from suppliers and technicians: main board, mainboard, control board, head board, carriage board, driver board, transfer board, adapter, decoder. This guide sorts them out and shows how faults map to each board. It follows our explanation of the UV flatbed head driver board.

The three main boards at a glance

FeatureMain boardHead (carriage) boardDriver board
LocationElectronics cabinetCarriageCarriage (integrated or separate)
Main jobMachine control and dataData distribution to headsFiring pulses for nozzles
Connects toPC, motors, encoder, sensors, lamps, vacuum, carriageMain board, heads, heaters, carriage sensorsHeads, head board
Typical failure symptomsNo connection, no motion, all heads stop, lamp or vacuum faultsOne head missing, heating errors, sensor errorsOvercurrent, faint heads, new heads failing
Common causesPower surges, earth faults, heat in cabinetInk, heat, cables, static, crashesShorted heads, heat, hot-plugging

The main board in detail

The main board receives print jobs from the RIP over USB or network, interprets them, and coordinates the whole machine. On flatbeds it controls more axes than a roll machine: X for the carriage, Y for the table or gantry, and Z for head height. On large gantry machines it synchronises two Y motors. It also controls vacuum zones, lamp switching and sometimes the white ink circulation pump. Because everything passes through it, a main board fault often stops the whole machine. Our guide to UV flatbed main board functions and ports covers it in depth.

The head board in detail

The head board, also called the carriage board, receives data from the main board through a flat cable or fibre and splits it between heads. It also controls head heaters, reads thermistors, and on many flatbeds reads the height sensor and anti-collision switch. On Epson-head machines it usually includes the driver section. See UV flatbed carriage board explained.

The driver board in detail

The driver section creates waveforms and delivers current to each piezo head. On Ricoh flatbeds it may be a separate board per head group. It is the board most often damaged by shorted heads and hot-plugging.

Other boards you may hear about

NameWhat it usually means
Transfer board / adapterSmall board above each head connecting head cables
DecoderBoard or chip that allows certain Epson heads to work with third-party boards
Motor driverSeparate drivers for servo or stepper motors in the cabinet
Lamp driver / power supplyPowers UV LED lamps, controlled by the main board
Ink supply boardControls pumps, level sensors and white circulation
Vacuum control relay boardSwitches vacuum pump and zones

UV flatbed driver board vs main board: fault mapping

SymptomMost likely boardCheck first
PC cannot connectMain boardUSB/network cable, PC settings, software
Carriage or table does not moveMain board or motor driverMotor cables, limit switches, driver alarms
Z-axis will not raise or lowerMain board or Z motor driverZ limit switches, motor cable
All heads stop togetherMain board or data linkMain data cable or fibre
One head missingHead board or headCable swap tests
Overcurrent on one headDriver or headHead resistance, cable
Lamps not switchingMain board or lamp driverLamp power supply, cables
Vacuum zones not switchingMain board or relay boardRelays, valves, wiring
Height sensor errorsHead board or sensorSensor, wiring

How the boards must match

Main board, head board and driver sections must come from the same system and compatible versions. A Hoson main board will not drive a Senyang head board, and different Hoson versions may not communicate. When replacing any one board, record the model and version of all of them. Our guide to UV flatbed board compatibility explains the rules.

Cost comparison

BoardIndicative listed price (late 2026)
Hoson A3 flatbed main board (i3200/XP600/TX800)About $304
Hoson 2-head main boardAbout $380
Hoson i3200 head board (1โ€“4 heads)About $388โ€“450
Hoson i3200 double carriage board (network)About $430
BYHX Gen5 4-head main boardAbout $845โ€“866
Ricoh Gen5 carriage boardsAbout $287โ€“652

Prices exclude shipping, duty and GST. A correct diagnosis avoids buying the wrong board.

Example: “main board fault” that was a cable

A Delhi shop’s flatbed stopped printing on all heads. The supplier suspected the main board. A technician found the main data cable cracked in the Y-axis cable chain. A new cable cost a small fraction of a main board.

Example: driver fault mistaken for head fault

A 2513 lost the same Ricoh head position twice. Rather than buying a third head, the owner had the driver group tested. It was faulty. Replacing it stopped the failures.

Signal path from RIP to nozzle

Following the signal path step by step makes the UV flatbed driver board vs main board distinction clear, and shows where faults can enter.

StepWhereWhat happensTypical failure point
1RIP PCImage is ripped into dot data for each channelRIP settings, profiles
2USB or network linkData sent to the printerCable, port, PC power settings
3Main boardData buffered, synchronised with encoder and motionMain board, firmware, encoder
4Main data cable or fibreData streamed to carriageCable chain wear
5Head boardData split per head and rowHead board logic, connectors
6Driver sectionWaveforms generated and appliedDriver channel, supply rail
7Head cable and adapterSignals carried to the headCable, adapter
8PrintheadPiezo elements fire dropsClogging, damage

A fault at any step can stop printing. Diagnosis works best when you test from the simplest and cheapest steps first: cables and settings before boards.

Power distribution between the boards

Each board needs power. The main board is usually fed from a power supply in the cabinet. The carriage boards receive power through cables in the cable chain, sometimes from a separate carriage power supply. Driver sections need a higher drive rail. Lamp drivers, motor drivers and vacuum pumps have their own supplies. A failed power supply can mimic a board fault, for example a carriage supply failure makes all heads disappear just as a head board fault would. Check power supply indicator lights and, with a technician, measure output voltages before condemning a board.

Power supplyFeedsFailure looks like
Main logic supplyMain boardMachine dead or not connecting
Carriage supplyHead and driver boardsAll heads missing
Motor supplyMotor driversNo motion, driver alarms
Lamp supplyUV LED lampsLamps off, under-curing

Board identification tips

When asking for help, describe boards by location and appearance as well as name. Photograph each board with its labels readable, note the number and type of connectors, and include a wide photo showing where it sits. For example: “board in the cabinet with USB, motor and encoder connectors” is the main board; “board under the carriage cover with four ribbon cable sockets” is the head board. This avoids confusion caused by suppliers using different names.

Which board to suspect after common events

EventBoard most at risk
Hot-plugging a head cableHead board and driver
Head crashHead board, adapter, driver
Lightning storm or surgeMain board, power supplies
Ink leak on carriageHead board
Cabinet fan failureMain board, motor drivers
Generator changeover spikePower supplies, main board
Static discharge from acrylicHead board, sometimes main board

Keeping all boards healthy

The main board benefits from a clean, cool cabinet with working fans and dust filters, plus good power protection. The head and driver boards benefit from clean carriages, working lamp cooling, careful head changes and static control. Schedule a monthly inspection of both areas, with power off, and record what you find. Our UV flatbed preventive maintenance checklist lists the tasks.

UV flatbed driver board vs main board: replacement differences

AspectMain board replacementHead/driver board replacement
Settings affectedMachine parameters, axes, vacuum, lamps, sometimes licenceHead voltages, temperatures, offsets
Licence or dongleOften tied to main boardRarely
Calibration afterAxis, height, step, bidirectionalHead alignment, bidirectional
Typical timeHalf a day or moreTwo to four hours
RiskLosing machine parametersDamaging heads if channel or cable faulty

Main board replacement often involves licence transfer or a new dongle, because many print control systems tie their licence to the main board. Ask the supplier about this before ordering. See our guide to UV flatbed main board replacement and licences.

Backups for each board

Before any board work, back up both machine parameters (stored on or associated with the main board) and head settings (voltages, temperatures, offsets). Machine parameters include axis directions, motor steps, encoder settings, Z-axis limits, height sensor offsets, vacuum zone mapping and lamp timing. Losing these can take a technician many hours to rebuild. Photograph every settings screen if export is not available, and store backups away from the printer PC.

Why naming matters when ordering

Ordering “a board” without specifying which one leads to costly mistakes. Some suppliers call the head board the “carriage board”, others call the main board the “control board” or “mainboard”. Always send photos, part numbers and versions, describe the board’s location, and confirm in writing exactly which board is being supplied. When in doubt, ask the supplier to mark the photo of the board they are quoting.

Which board to call about first

When a fault appears, start with the cheapest and most accessible checks: cables, settings and power supplies. Then work along the signal path. If the PC cannot see the printer, start at the main board end. If one head misbehaves, start at the carriage. Clear thinking about which board does what saves hours of guesswork and avoids ordering the wrong part.

Bottom line

For the UV flatbed driver board vs main board question, remember: the main board controls the machine, the head board distributes data on the carriage, and the driver fires the nozzles. Map symptoms to the right board, check cables first, match versions across all boards, and test drivers before replacing heads.

Further reading: Each of these is a multi-layer printed circuit board carrying its own processors, regulators and connectors.

Key takeaways

  • The main board controls motors, sensors, lamps, vacuum and data from the PC.
  • The head board distributes data to heads and controls heating and carriage sensors.
  • The driver creates firing pulses and is often integrated in the head board.
  • Symptoms point to specific boards; cables often mimic board faults.
  • All boards must come from the same system and compatible versions.

More in the UV flatbed head driver board series

Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.

Running a UV roll to roll machine as well? The matching guide in our roll to roll series is Head Driver Board vs Head Board vs Mainboard.

Frequently Asked Questions

What is the difference between a UV flatbed driver board and main board?

The main board controls the whole machine from the cabinet; the driver creates firing pulses for heads on the carriage.

Is the head board the same as the carriage board?

Yes, the terms are generally used for the same board on the carriage.

Where is the driver on Epson-head flatbeds?

Usually built into the Hoson or Senyang head board.

Which board controls the Z-axis?

The main board, often through a separate motor driver.

What does it mean if all heads stop together?

Usually a main board, data cable or power problem rather than a head board fault.

Which board controls UV lamps?

The main board controls lamp switching through a lamp driver or power supply.

What is a transfer board?

A small adapter board above each head that connects head cables.

Can I mix boards from different systems?

No. Main, head and driver boards must come from the same system and compatible versions.

How much does a Hoson flatbed main board cost?

Late 2026 listings showed about $304 for an A3 flatbed main board and about $380 for a 2-head main board.

How do I know which board has failed?

Map the symptom to the board, check cables and run swap tests before buying.

Which board controls vacuum zones?

The main board, usually through relays or a separate relay board.

Can a cable fault look like a main board fault?

Yes. A cracked main data cable can stop all heads.

What is a decoder?

A board or chip that allows some Epson heads to work with third-party boards.

Can Unified Engineering Dynamics help identify my boards?

Yes. Send photos of each board and our team will help identify them.

Can a power supply failure look like a board failure?

Yes. A failed carriage supply makes all heads disappear, just like a head board fault.

Which board is most at risk after a lightning storm?

Usually the main board and power supplies.

How should I describe a board to a supplier?

Give its location, connectors, labels and clear photos, not just a name.

What path does print data take?

From the RIP PC to the main board, through the data cable to the head board, then the driver and head.

Is the licence tied to the main board?

Often yes. Ask the supplier about licence transfer or dongles before replacing a main board.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *