Direct answer: On a UV roll to roll printer, the mainboard sits in the electronics cabinet and controls the whole machine: it receives the print job from the PC, drives the carriage and media motors, reads the encoder and sensors, and sends print data to the carriage. The head board (also called the carriage board) rides on the carriage and splits that data into streams for each printhead, controls head heaters and reads head temperatures. The driver board, or driver section, generates and applies the high-voltage firing waveform that makes each head eject ink. In a UV driver board vs mainboard comparison, the driver is closest to the heads and handles power, while the mainboard is the “brain” that coordinates everything. Knowing which board does what helps you diagnose faults and avoid buying the wrong part.
Getting the UV driver board vs mainboard question right is the first step to a correct diagnosis and avoids buying an expensive board you never needed.

Table of Contents
Technicians, traders and owners often use these names loosely. One person’s “head board” is another person’s “carriage board”, and some board systems combine the driver and head functions on one board. This guide clears up the confusion for UV roll to roll printers using BYHX, Hoson, Senyang and similar board systems with Ricoh, Konica, Kyocera or Epson heads. For background, see our explanation of the UV roll to roll head driver board and our guide to the UV carriage board.
UV driver board vs mainboard vs head board at a glance
| Board | Location | Main jobs | Typical failure clues |
|---|---|---|---|
| Mainboard | Electronics cabinet | PC communication, motion control, encoder, sensors, data to carriage | Machine not connecting, wrong movement, all heads affected, sensor errors |
| Head board / carriage board | On the carriage | Data distribution to heads, heater control, head temperature reading | One or more heads not printing, heater errors, data errors |
| Driver board / driver section | On the carriage, often with heat sinks | Generating and applying firing waveform | Weak jetting, overcurrent errors, faults when warm, burnt components |
The mainboard in detail
Communication with the PC
The mainboard connects to the RIP and print control software through USB, Ethernet or a fibre link, depending on the system. It receives the processed print data and settings and reports machine status back to the software.
Motion control
It controls the carriage motor (often a servo), the media feed motor, take-up and feed rollers, and sometimes lamp shutters or lifting mechanisms. It reads the linear encoder strip to know exactly where the carriage is, so drops land in the right place.
Sensors and safety
Media sensors, limit switches, ink level sensors and emergency stops usually connect to the mainboard or a sub-board linked to it.
Data to the carriage
The mainboard sends print data and timing signals through data cables or fibre to the carriage board. This link carries large amounts of data at high speed.
Licence and configuration
On many systems, the mainboard holds firmware, configuration and links to the software licence or dongle. Replacing it may require reconfiguration, which we explain in our guide to UV main board replacement.
The head board (carriage board) in detail
Data distribution
The head board receives combined data from the mainboard and splits it into separate data streams for each head and colour, synchronised with carriage position.
Heater and temperature control
Ricoh and Konica heads have internal heaters and thermistors. The head board powers the heaters and reads temperatures so the software can keep UV ink at the right jetting viscosity.
Connection hub
Head data cables, heater wires, sometimes lamp signals and carriage sensors connect to this board. It is often the busiest connector area on the machine.
The driver board in detail
Waveform generation
The driver creates the precise voltage pulses that flex the piezo actuators in each head. Waveform shape and voltage affect drop size, speed and placement.
Power delivery
The driver must supply current to many nozzles at once. Power components and heat sinks are usually visible on this board or section.
Per-head settings
Voltage settings in software are applied by the driver to each head. Correct settings are essential, as we explain in our guide to Ricoh Gen5 head voltage and waveform for UV ink.
When boards are combined
Different board systems divide work differently:
- Some combine the head board and driver on one carriage board, with power components and heat sinks on the same PCB.
- Some use a carriage board plus separate driver boards for each pair or group of heads.
- Some use small adapter boards on each head, which may include part of the driver circuitry.
- Small machines with Epson heads may use a compact two-board set: mainboard plus carriage board.
Marketplace listings reflect this. A “Ricoh Gen5 4H board kit” usually includes mainboard, carriage board and adapters, while a “G5 driver board” might be sold separately for systems that use one. Always identify your board system before ordering. Our article on Hoson, Senyang and BYHX carriage boards for Ricoh Gen5 helps with identification.
How to tell which board is faulty
A structured approach based on what the symptoms affect is the quickest way to narrow down a fault.
| Symptom | Most likely board | Also check |
|---|---|---|
| Printer not detected by PC | Mainboard or connection | USB/network cable, PC port, drivers, power |
| Carriage moves wrongly or hits limits | Mainboard or motor driver | Encoder strip, motor, belt, limit sensors |
| All heads stop printing together | Mainboard data link or carriage board | Data cable or fibre between cabinet and carriage |
| One head stops printing | Head board channel or driver | Head, head cable, settings |
| Weak jetting on one head, worse when warm | Driver | Cooling, head temperature, ink supply |
| Heater or temperature error | Head board | Head thermistor, heater wiring |
| Overcurrent error | Driver or head | Head short, cable damage |
Fault-following tests are the most reliable method. Swap heads or cables between channels with power off and see whether the fault moves with the head, the cable or the board channel. Our article on head data cable vs carriage board faults explains this technique.
Cost differences
Board costs vary widely with system and head type. Indicative prices from marketplaces in late 2026:
| Item | Indicative price | Source |
|---|---|---|
| BYHX G5 driver board | About $200–220 | Chinese marketplace |
| Ricoh Gen5 carriage boards | About $287–652 | Chinese marketplaces |
| BYHX Gen5 4-head main board | About $845–866 | Chinese marketplace |
| Ricoh Gen5 4-head board kit | About $1,360–1,770 | Chinese marketplaces |
| BYHX KM512 head plus main board set | About ₹75,000 | Indian trader |
Add shipping, customs duty and GST for imported parts. Prices are indicative and change often. Our guide to UV roll to roll main board prices in India covers this in more detail.
Why the distinction matters
Avoid buying the wrong part
Ordering a mainboard when the fault is in a driver section wastes money and time. Clear diagnosis comes first.
Protect new heads
A faulty driver can damage a new head. Knowing the driver’s role helps you check it before fitting expensive heads.
Plan spares
Driver and head boards on the carriage face heat, ink and cable stress, so they fail more often than mainboards in clean cabinets. Many units keep a spare carriage board or driver board but not a spare mainboard.
Communicate with suppliers
Using the right names, plus board photos and labels, helps suppliers confirm compatibility quickly.
Example: “mainboard” that was a driver fault
A unit in Kanpur was told by a local technician that their mainboard had failed because the cyan and magenta channels printed weakly. Before buying a new mainboard, they asked for a second opinion. Testing showed motion, encoder and PC communication were fine and the other heads printed normally. Swapping heads proved the fault stayed with the channel, and measurements found a weak driver section with a failed cooling fan. Replacing the fan and repairing the driver solved the problem at a fraction of the cost of a mainboard.
Example: data link fault mistaken for a head board
Another unit lost all printing while motion still worked. They suspected the head board. A technician found the data cable between the cabinet and carriage had worn through in the cable chain. A new cable fixed the problem. Symptoms affecting all heads point to shared parts, such as the data link, rather than individual channels.
Other boards you will find on a UV roll to roll printer
Besides the three main boards, most UV roll to roll printers have several smaller boards. Knowing them avoids confusion when a technician mentions them.
| Board | Typical location | Function |
|---|---|---|
| Adapter or transfer board | Directly above each head | Connects the head to its data cable; may include part of the driver or heater circuit |
| Motor driver or servo driver | Electronics cabinet | Powers carriage and media motors on commands from the mainboard |
| Ink control board | Near ink tanks or cabinet | Controls ink pumps, level sensors and white ink circulation |
| Lamp driver or lamp power supply | Cabinet or carriage | Powers and switches the UV LED lamps |
| Sensor or interface board | Various | Connects media sensors, limit switches and safety interlocks |
| Power supplies | Cabinet | Convert mains to the voltages each board needs |
A fault in any of these can look like a mainboard or carriage board fault. For example, a failing lamp power supply can cause lamp errors that the mainboard reports, and a failing servo driver can cause carriage errors. Always check the smaller boards and power supplies before replacing a major board.
Signals that travel between the boards
Understanding what passes between boards helps you think about where a fault could be.
Mainboard to carriage board
Print data, timing signals derived from the encoder, configuration and commands such as heater set points. On many systems this travels through a set of flat cables, a high-speed data cable or a fibre-optic link running along the cable chain. Because the carriage moves constantly, these cables flex millions of times over their life and are a common failure point.
Carriage board to driver
Timing and control signals telling the driver when to produce pulses, plus settings for each head. On combined boards, this happens on the same PCB.
Driver to heads
The firing waveform and supporting signals, carried through short cables or adapter boards to each head. Data for nozzle selection usually travels with these signals.
Heads back to carriage board
Temperature readings from each head’s thermistor, and on some systems, status signals. These let the software control heaters and detect faults.
A quick checklist before calling it a “mainboard fault”
- Is the PC connection working? Try a different cable or port.
- Are all power supply voltages present and correct?
- Is the data link between cabinet and carriage intact along its full length?
- Do motion and sensors work normally?
- Do some heads print while others do not? That points away from the mainboard.
- Has anything changed recently: software update, new head, wiring work, a storm?
If motion, sensors and connection all work and only some heads misbehave, the mainboard is rarely the cause. Look first at carriage boards, drivers, cables and heads. Our guide to the UV carriage board replacement checklist covers what to check before replacing the carriage board itself.
Labelling and documentation
When your machine is working well, take time to photograph every board, its labels, connectors and cable routes. Record board versions and firmware shown in the software. Keep these photos in a shared folder. When something fails, you will be able to tell suppliers exactly what you need and reassemble the machine correctly. Mark cables with small labels showing which connector they belong to; it saves hours during repairs and avoids dangerous wrong connections.
Board responsibility and replacement frequency
| Board | Environment | Relative failure rate | Spare stocking |
|---|---|---|---|
| Mainboard | Clean, cool cabinet | Low | Optional for most units |
| Carriage / head board | Heat, ink mist, vibration, static | Higher | Recommended for busy machines |
| Driver board / section | Heat, high current, head faults | Higher | Recommended where separate |
| Adapter boards | Directly above heads | Moderate | Inexpensive; keep one or two |
| Data cables | Constant flexing | Moderate to high | Keep a full set |
Board names used by traders and technicians
Different people use different names for the same board. This glossary helps when you read listings or talk to technicians in India and abroad.
| Name you may hear | Usually means |
|---|---|
| Main board, mainboard, motherboard, control board | The cabinet board that controls the machine |
| Head board, carriage board, print head board | The board on the carriage that distributes data |
| Driver board, head driver, drive board | The board or section producing firing waveforms |
| Adapter board, transfer board, connector board | Small board above each head |
| Board kit, board set | Mainboard plus carriage board, often with adapters and cables |
| Sub-board | Varies: sometimes carriage board, sometimes an extension board |
Because “sub-board” and “head board” can mean different things to different sellers, always rely on photos and part numbers rather than names alone. Chinese listings for Ricoh Gen6 systems, for example, may list a “mainboard”, a “sub-board” and an “adapter board” separately, each at quite different prices.
What to tell a technician on the phone
When you call for remote help, a clear description saves time:
- Printer make, model, width and age.
- Board system and software name.
- Head type and number of heads.
- Exact symptom: what works, what does not, and since when.
- Error messages, word for word or as a screenshot.
- What you have already checked or swapped.
- Any recent events: power cut, storm, head change, software update, ink change.
With this information, an experienced technician can often tell whether the fault is likely in the mainboard, carriage board, driver, cable or head before visiting, and bring the right parts.
Safety when working near boards
Driver boards use voltages that can be dangerous, and power supplies hold charge after switch-off. Always switch off and unplug the machine, wait for capacitors to discharge as advised by the maker, wear an anti-static wrist strap connected to earth, and never touch board components with bare fingers. Keep liquids, including cleaning fluid and UV ink, away from open electronics. UV ink is also a skin sensitiser, so wear gloves when handling ink-contaminated parts.
Bottom line for owners
You do not need to repair boards yourself, but knowing which board does what lets you ask better questions, spot wrong diagnoses and avoid paying for parts you do not need. Keep board photos, version numbers and a fault log, and insist on fault-following tests before any expensive board is replaced.
Further reading: All of these boards are printed circuit boards built for very different jobs, from motion control to high-voltage firing.
Key takeaways
- The mainboard controls the whole machine; the head board distributes data and controls heaters; the driver generates the firing waveform.
- Some systems combine head and driver functions on one carriage board.
- Symptoms affecting all heads suggest the mainboard or data link; single-head symptoms suggest a channel, driver, head or cable.
- Fault-following tests are the best way to locate faults.
- Identify your board system and send photos when ordering parts.
More in the UV head driver board series
- UV Roll to Roll Head Driver Board Explained
- UV Head Driver Board Failure Signs
- Why a Bad Driver Board Can Kill a New Ricoh Head
- Ricoh Gen5/Gen6 Head Voltage and Waveform for UV Ink
- UV Driver Board Compatibility: Ricoh, Konica, Kyocera, Epson
- UV Driver Board Repair vs Replacement
- Power Fluctuation: Stabilizer, UPS and Earthing
- UV LED Lamp Cooling, Chillers and Board Overheating
Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.
Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine head driver board and the eco-solvent printer fire board.
Frequently Asked Questions
What is the difference between a UV driver board and a mainboard?
The mainboard controls the whole printer, including PC communication, motion and sensors. The driver board generates the high-voltage waveform that fires the printheads.
Is the head board the same as the carriage board?
Usually yes. Both names describe the board on the carriage that distributes data to the heads and controls heaters.
Where is the mainboard located?
It is usually in the electronics cabinet at one end of the printer, away from the carriage.
Can one board do both head and driver functions?
Yes. Many board systems combine data distribution and driver circuits on one carriage board.
Which board fails most often on UV roll to roll printers?
Boards on the carriage, including head and driver boards, fail more often because of lamp heat, ink mist, static and cable stress.
How do I know if my mainboard has failed?
Symptoms such as the printer not connecting, wrong carriage movement, sensor errors or all heads failing together point to the mainboard or its links.
Can I replace a driver board without changing the mainboard?
Usually yes, if the replacement matches your board system and version.
Why do suppliers ask for board photos?
Names vary between traders. Photos of labels, connectors and versions help confirm the correct part.
Is a mainboard more expensive than a driver board?
Generally yes. Main boards often cost several times more than individual driver boards, though prices vary by system.
Can a mainboard fault damage heads?
It is less common than driver faults, but power problems can affect several boards and heads together.
Should I keep a spare mainboard?
Most units keep spare carriage or driver boards instead, because those fail more often. Large operations may keep a spare mainboard.
Can Unified Engineering Dynamics identify my boards?
Yes. Send photos of labels and connectors and our team can help identify boards and advise on compatible replacements.
What is an adapter board on a UV printer?
It is a small board fitted directly above each head that connects the head to its data cable. On some systems it also carries part of the driver or heater circuit.
Can a power supply fault look like a mainboard fault?
Yes. Missing or unstable supply voltages can cause resets, errors and communication failures. Check power supplies before replacing the mainboard.
What does “sub-board” mean in a listing?
It varies by seller. It may mean the carriage board or an extension board. Rely on photos and part numbers rather than the name alone.