UV Printing

UV Flatbed Head Board Failure Symptoms: Missing Heads, Random Nozzles and Head Errors

UV Flatbed Head Board Failure: 7 Symptoms and Look-Alikes

Direct answer: The classic signs of UV flatbed head board failure are a head or colour channel that stays blank after good cleaning and a confirmed ink supply, “head not found” or head board communication errors, heads that will not heat or show impossible temperatures, faults that move with the board channel rather than with the head, intermittent missing lines that worsen as the carriage warms up, and visible burn marks or a burning smell. However, the same symptoms often come from clogged nozzles, air in the dampers, cracked head cables, a failing power supply or a faulty main board. Confirm a head board fault with careful swap tests, done with the power off, before buying a new board.

Recognising true UV flatbed head board failure, and ruling out clogging, white ink and cable look-alikes, prevents costly and unnecessary board and head purchases.

UV Flatbed Head Board Failure: 7 Symptoms and Look-Alikes
UV Flatbed Head Board Failure: 7 Symptoms and Look-Alikes

On a UV flatbed, missing print can cost a whole sheet of acrylic, glass or MDF, so operators are often tempted to replace the head board at the first sign of trouble. That can be an expensive mistake. This guide lists the real symptoms of head board failure, the look-alike faults, and a step-by-step way to confirm the cause. It follows our explanation of the UV flatbed carriage board.

Seven symptoms of head board failure

1. A head stays blank after good cleaning

If a head prints nothing even after cleaning, a fresh nozzle check and confirmed ink flow, the problem may be electrical: the head board channel, the cable, the driver section or the head itself.

2. “Head not found” or head board errors

Software messages such as “head not detected”, “head board communication error” or similar codes point to a broken link between the main board, carriage board and heads. Loose cables are as likely as failed boards.

3. Heating faults

UV ink must be kept warm to jet properly. A head that never reaches temperature, shows a reading far from its neighbours or jumps erratically may have a heater channel fault on the board, a loose connector or a failed thermistor.

4. Faults that follow the channel

If you swap two head cables at the board end and the fault stays in the same board position, the channel is suspect. If it moves with the head, the head or its cable is suspect.

5. Faults that appear when warm

A board with a cracked solder joint or ageing component may work in the morning and fail after an hour of printing, as lamp heat warms the carriage.

6. Random missing lines or garbled printing

Data errors on the carriage board, or in its link to the main board, can cause scattered missing bands, garbled patterns or prints that stop halfway.

7. Burn marks and smells

Brown or black marks, melted connectors, swollen capacitors or a burning smell are definite signs of damage. Switch off immediately and investigate before powering up again.

Look-alike faults

SymptomPossible non-board causes
Head blankClogged nozzles, cured ink on nozzle plate, empty damper, air, closed valve
White head blankSettled white pigment, stopped circulation, blocked filter
Head not foundLoose or cracked cable, wrong cable orientation, software or firmware mismatch
Heating faultLoose heater connector, failed thermistor, wrong temperature setting
Random linesEncoder dirt, static discharge from acrylic, cable damage in cable chain
All heads stopData link, main board, power supply, PC or USB setting
Faults when warmSlow carriage fan, weak lamp cooling, failing power supply

White ink problems are particularly common on flatbeds. See our guide to UV white ink circulation parts.

Step-by-step confirmation

  1. Record the symptom. Which head, which colour, when it started, what changed, any error codes.
  2. Check ink. Damper levels, filters, valves, white circulation, negative pressure.
  3. Clean and test. Run cleaning, print a nozzle check, inspect the nozzle plate for cured ink.
  4. Check temperature. Compare the head’s temperature with its neighbours.
  5. Inspect cables. With power off, check both ends of the head cable for seating, damage and ink.
  6. Swap cables. With power off, swap with a known good spare or with a neighbouring head’s cable.
  7. Swap channels. With power off, swap two heads’ cables at the board end, unless one head might be shorted.
  8. Inspect the board. With power off, look for burns, ink, corrosion and swollen parts.
  9. Call a technician for measurements if the fault follows the channel.

Our article on head cable vs carriage board faults explains safe swap testing in detail.

Small flatbeds: Epson head specifics

On A3 and A2 flatbeds with XP600, TX800 or i3200-U1 heads, each head connects through flat ribbon cables that are easily inserted at an angle. A single misaligned cable can short pins and burn both the head and the board channel. The i3200-U1 is particularly sensitive; at around ₹78,000–95,000 per head in Indian listings, an error is costly. If a board channel burns, always replace the cable, check the head’s resistance with a technician and inspect the adapter before fitting anything new.

Industrial flatbeds: Ricoh head specifics

On 2513 and 3020 flatbeds with Ricoh Gen5 or Gen6 heads, the board often drives several heads per section. A fault affecting a group of heads together points to a shared section, cable bundle or power rail. A fault affecting one head points to that head’s channel, cable or adapter. Overcurrent errors on Ricoh heads should always be investigated before replacing the head, because a damaged driver channel can destroy a new head worth well over a lakh of rupees.

Error codes

Error codes vary by board system and software. Note the exact wording and code, check the software manual, and ask your supplier. Typical meanings:

Type of messageLikely meaning
Head not found / not detectedCable, adapter, head, board channel or firmware
Head board communication errorData link, cable, carriage board or main board
Overcurrent / head shortShorted head, cable or driver channel
Temperature errorHeater, thermistor, connector or heater channel
Height sensor or collision errorSensor, wiring, real obstruction or carriage board input

What causes head board failure

  • Hot-plugging head cables.
  • Fitting a shorted head.
  • Ink leaks onto the board.
  • Ink mist build-up cured by stray UV light.
  • Lamp heat and slow fans.
  • Static discharges from acrylic and PVC sheets.
  • Head crashes on warped or raised substrates.
  • Power surges and poor earthing.

After confirming a board fault

  1. Find and fix the root cause.
  2. Identify the board precisely: system, model, version, head type.
  3. Decide between repair and replacement.
  4. Replace damaged cables and adapters at the same time.
  5. Test heads before connecting them to the new board.
  6. Restore settings and print test files.

See our UV flatbed carriage board replacement checklist.

Example: white head blank on an A3 flatbed

A phone-cover printer in Delhi lost the white head on an i3200 flatbed. The owner assumed the head board had failed. Checks showed the white circulation pump had stopped and pigment had settled in the damper. After restoring circulation and cleaning, the head printed normally. No board was needed.

Example: head 3 dead on a 2513

A signage unit’s Ricoh Gen5 flatbed showed head 3 blank. Cleaning did nothing. Swapping cables at the board end moved the fault to head 4’s position, proving the board channel was fine and the head or cable was at fault. A spare cable restored head 3. The old cable had cracked in the cable chain.

Symptom-to-cause quick table for UV flatbed head board failure

Use this table as a first filter. It lists each common symptom, the probability that the head board is responsible, and the cheaper checks to complete first.

SymptomBoard likely?Check first
One colour missing, others fineLow to mediumDamper, nozzle plate, cable seating, cable swap
White head blankLowCirculation pump, white filter, pigment settling
All heads blankLow for carriage boardMain data cable, main board, power supply, PC link
Head not found after head changeMediumCable orientation, offset insertion, locks
Overcurrent alarm on one headMedium to highHead resistance, cable short, ink on pins
Temperature reads zero or maximumMediumThermistor plug, heater connector
Fault after warm-up onlyMediumFans, chiller, lamp heat, then board
Burn mark visibleHighRoot cause before replacement

Reading the nozzle check correctly

The nozzle check is the most useful diagnostic print on a flatbed, but it is often misread. Print it on a white or light-coloured material, or on transparent film over white paper for the white channel. Look at the pattern carefully:

  • Scattered missing nozzles across a row usually mean clogging or air, not electronics.
  • A whole row missing on an i3200-U1 can be an ink supply problem for that colour or a data problem for that row. Check the damper first, then the cable.
  • Every row of one head missing points to the head, its cable or its board channel.
  • Blocks of nozzles missing in a regular pattern can indicate a cable conductor fault, because each conductor carries data for a group of nozzles.
  • Deflected or misty lines often mean static or a damaged nozzle plate, not a board problem.

Keep dated nozzle check prints for each head. Comparing today’s pattern with last week’s shows whether a fault is new, worsening or long-standing.

Environmental triggers that mimic board failure

Flatbeds in Indian workshops face heat, dust, humidity swings and unstable power. Each of these can produce symptoms that look like head board failure:

ConditionEffectFix
Room above 35°C in summerCarriage overheats, random faultsVentilation or air conditioning, clean fans
Dry winter airStatic on acrylic, feathered prints, data errorsEarthing, ionising bar, moderate humidity
Monsoon humidityCondensation, corrosion on connectorsKeep room dry, avoid cold starts in humid air
Dust from cutting MDF or acrylic nearbyClogged fans and encoderSeparate cutting area, weekly cleaning
Voltage dips and surgesResets, communication errorsStabiliser, online UPS, proper earth

Our article on UV flatbed printer problems and fixes lists many more environment-related issues.

Keeping a fault log

A simple notebook or spreadsheet can save hours of diagnosis. For each fault, record the date, machine hours if available, symptom, error message, room temperature, what changed, tests done and result, and parts replaced. After a few months, patterns appear: faults every afternoon point to heat, faults after acrylic jobs point to static, faults after head changes point to handling. A log also supports warranty claims, because suppliers want to see what was tested before a board was condemned. Our UV flatbed warranty claim guide explains what evidence suppliers usually ask for.

When the board really has failed

If the fault follows the board channel, visible damage exists, or a technician measures a failed component, the board needs repair or replacement. Before ordering, make sure every head that was connected to the failed channel has been checked, because a shorted head will destroy a new board. Replace any cable involved, clean ink from the carriage, and correct the root cause, whether that is a leaking damper, a weak fan, missing earth or careless handling.

Head board failure on rotary and jig jobs

Flatbeds that print bottles and tumblers on a rotary attachment, or many small items on a jig, raise the carriage higher than usual and often run long jobs with heads idling over empty areas. Higher head gaps increase ink mist, and long jobs heat the carriage. If faults appear mainly on rotary or jig work, clean the carriage more often, check fans and lamp cooling, and confirm the rotary’s own cable and connector to the board are secure. A loose rotary connector can produce errors that look like a head board failure.

Bottom line

UV flatbed head board failure has clear symptoms, but most of them have cheaper look-alikes. Check ink, white circulation, cleaning, temperature and cables first, then use careful swap tests with power off to see whether the fault follows the head, cable or board channel. Only then buy a board, and fix the root cause before fitting it.

Further reading: The isolation routine above follows standard troubleshooting practice: test the simplest, most likely causes first.

Key takeaways

  • Blank heads after cleaning, head not found errors, heating faults and burn marks suggest head board failure.
  • Clogging, white ink settling, cables, encoder dirt and static often cause the same symptoms.
  • Swap tests with power off show whether a fault follows the head, cable or channel.
  • Never move a possibly shorted head onto a healthy channel.
  • Fix the root cause and replace damaged cables with the board.

More in the UV flatbed carriage board series

Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.

Running a UV roll to roll machine as well? The matching guide in our roll to roll series is UV Head Board Failure Symptoms.

Frequently Asked Questions

What are the signs of UV flatbed head board failure?

Heads blank after cleaning, head not found errors, heating faults, faults that follow the board channel, faults when warm, garbled printing and burn marks.

Can a clogged head look like a board failure?

Yes. Clogged nozzles, cured ink and air in dampers often look like board faults. Clean and check ink first.

Why is my white head blank?

Usually settled white pigment, stopped circulation or a blocked filter, not a board fault.

How do I test whether the board channel is faulty?

With power off, swap two head cables at the board end. If the fault stays in the same position, suspect the channel.

Is it safe to swap heads between channels?

Only with power off, and never move a head that might be shorted onto a healthy channel.

What does a head not found error mean?

A broken link involving the cable, adapter, head, board channel or firmware.

Can static from acrylic sheets cause random lines?

Yes. Static discharges can disrupt data on the carriage. Good earthing reduces the problem.

Why do faults appear only when the machine is warm?

Heat from lamps can expose cracked solder joints or ageing parts, or overload weak cooling.

What should I do if I see burn marks?

Switch off, investigate the cause and do not power up until damaged parts are replaced.

Should I replace the cable when the board fails?

Yes. Cables involved in a short are often damaged and can harm a new board.

Are i3200-U1 heads expensive to replace?

Yes. Indian listings in 2026 ranged from about ₹78,000 to ₹95,000 per head.

Can a bad board damage a new Ricoh head?

Yes. Test the driver channel before fitting a new head after any failure.

How do I know which board to buy?

Note system, model, version, head type and main board details, and confirm with the supplier.

Can Unified Engineering Dynamics help diagnose head board faults?

Yes. Send symptoms, error codes and photos and our team will help identify the cause and the right parts.

What does a whole row missing on an i3200 head mean?

It can be an ink supply problem for that colour or a data problem for that row. Check the damper first, then the cable.

Can hot weather cause head board errors?

Yes. High room temperatures overload carriage cooling and can cause random faults.

Why should I keep a fault log?

It reveals patterns such as heat, static or handling problems and supports warranty claims.

Can rotary printing cause head board errors?

Indirectly. Higher head gaps and long jobs increase mist and heat, and a loose rotary connector can trigger errors.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *