Eco Solvent Printing

Carriage Board Price in India: New, Refurbished and Repaired Options Compared

Carriage Board Price in India 2026: New vs Refurbished

Direct answer: In the Indian market in late 2026, a new genuine carriage (head) board for a single-head XP600 eco-solvent printer typically costs in the range of about ₹10,000 to ₹22,000, a single-head i3200 board about ₹14,000 to ₹28,000, and a double-head i3200 carriage board about ₹22,000 to ₹45,000, before GST and installation. Complete board kits (mainboard plus carriage board) usually run from about ₹28,000 for basic single-head kits to ₹70,000 or more for double i3200 kits, and kits bundled with heads can exceed ₹1,00,000. Refurbished boards often sell at roughly 40 to 70 percent of the new price, and board-level repair commonly costs a few thousand rupees up to around ₹12,000 depending on the damage. These are indicative ranges only; actual prices depend on brand, version, supplier, exchange rates and whether installation, cables and warranty are included.

The carriage board price you pay depends on head type, board brand, condition and support, so the ranges below are indicative only.

Carriage Board Price in India 2026: New vs Refurbished
Carriage Board Price in India 2026: New vs Refurbished

Price is only one part of the decision. A cheap board that fails in a month, or damages a ₹40,000 printhead, is not cheap. This guide gives indicative price bands, explains what drives the differences, compares new, refurbished and repaired options, and shows how to calculate the true cost of each choice. For an overview of what the board does, see our explainer on the eco-solvent head carriage board.

Important note about the prices in this article

Board prices in India change often. Most boards are imported, so exchange rates, freight, customs duty and supplier margins all affect the final price. The same board can be quoted very differently by different sellers, and online listings may show prices that include or exclude GST, cables, firmware support or heads. The ranges below are based on market listings and supplier quotes seen in the Indian market in late 2026. Use them to judge whether a quote is reasonable, then get current written quotes for your exact board model and version.

Indicative carriage board price ranges for new boards

Board typeIndicative price range (excl. GST)Notes
Single-head XP600 carriage board₹10,000 – ₹22,000Wide variation by brand and version; older versions may be harder to find
Double-head XP600 carriage board₹16,000 – ₹32,000Must match mainboard version
Single-head i3200 carriage board₹14,000 – ₹28,000Check head variant support
Double-head i3200 carriage board₹22,000 – ₹45,000Most common in current production machines
DX5 / DX7 carriage board₹15,000 – ₹40,000Older systems; availability varies
Three- or four-head carriage boards₹35,000 – ₹70,000+Higher-end machines; often supplier-specific
i3200 adapter / transfer board₹800 – ₹3,000 eachSmall but frequently damaged

BYHX boards and boards for industrial machines usually sit at the higher end or above these ranges. Hoson and Senyang boards for common machines generally fall within them, with Senyang often slightly lower. Our article on Hoson vs Senyang vs BYHX carriage boards explains the differences between systems.

Indicative prices for complete board kits

Kit typeIndicative price range (excl. GST)Typical contents
Single-head XP600 kit₹28,000 – ₹45,000Mainboard, carriage board, data cable, head cables, software
Double-head XP600 kit₹35,000 – ₹55,000As above, for two heads
Single-head i3200 kit₹32,000 – ₹50,000Mainboard, carriage board, adapter boards, cables, software
Double-head i3200 kit₹45,000 – ₹70,000Most common upgrade kit for production shops
Kits bundled with heads₹1,00,000 – ₹1,50,000+Board kit plus one or two heads; price depends heavily on heads

When comparing kit quotes, check exactly what is included. Some quotes include only the two boards; others include cables, adapter boards, software dongle or licence, firmware support and installation. A kit that looks cheaper may need ₹5,000 to ₹10,000 of extra parts.

ItemIndicative cost
Head cable (each)₹300 – ₹1,500
Data cable₹1,000 – ₹5,000 depending on type and length
Technician visit (local, diagnosis and installation)₹1,500 – ₹5,000 per visit
Outstation technician visitVisit charge plus travel and stay
Calibration and colour profilingOften included in installation; otherwise charged separately
Board-level repair₹2,500 – ₹12,000 depending on damage
Courier to and from repair centreA few hundred rupees plus packaging

What drives price differences

Two quotes for “the same” board can differ by thousands of rupees. The main reasons are:

  • Brand and authenticity: genuine boards from the original board maker cost more than copies or unbranded boards.
  • Version: newer versions supporting more features or heads may cost more; obsolete versions may cost more because of scarcity.
  • Head count: double-head and multi-head boards have more channels and components.
  • New, refurbished or repaired: condition and testing affect price and risk.
  • Supplier type: authorised distributors, machine suppliers, spare parts traders and online marketplaces have different costs and margins.
  • Import route: exchange rates, freight, customs duty and stock levels.
  • Inclusions: cables, adapter boards, firmware support, activation, installation and warranty.
  • Machine locking: boards that need manufacturer activation may only be available through the machine supplier, sometimes at higher prices.

New boards: pros, cons and when to choose

Pros: correct version is easier to confirm, components have full life, warranty is usually offered, and support for firmware and installation is more likely.

Cons: highest upfront cost; for obsolete versions, new stock may not exist.

Choose new when: the machine is a key production asset, the board is a current version, the old board has extensive burn or ink damage, or when you are installing new expensive printheads and want to minimise risk.

Refurbished boards: pros, cons and when to choose

A refurbished board is a used board that has been inspected, cleaned, repaired where necessary and tested. Quality varies greatly between suppliers.

Pros: lower price, typically around 40 to 70 percent of new; sometimes the only option for obsolete versions.

Cons: unknown history, components have some wear, shorter or no warranty, and testing quality varies. A poorly refurbished board can damage heads.

Choose refurbished when: the supplier is reliable, the board has been tested with the correct head type, a warranty of at least a few weeks to months is offered, and the machine is a secondary or backup machine, or the version is obsolete.

Ask exactly what was done: which components were replaced, how the board was tested, with which heads, and for how long. Avoid “pulled from working machine” boards with no testing or warranty.

Repaired boards: pros, cons and when to choose

Board-level repair means sending your own failed board to a repair technician who identifies and replaces failed components.

Pros: often the lowest cost; you keep your original board, so version matching is not a concern; useful for obsolete or locked boards.

Cons: turnaround time can be several days to weeks; not every board can be repaired; repaired boards may fail again if other components were stressed; warranty on repairs is usually short.

Choose repair when: the damage is limited (for example a connector, a regulator or a few driver components), the board is otherwise clean and not corroded, the version is hard to replace, and you can tolerate the downtime or have a backup board.

Boards with heavy ink corrosion, large burned areas or damaged processors are usually poor repair candidates.

Comparison table

FactorNewRefurbishedRepaired (own board)
Typical costHighestAbout 40–70% of newOften lowest
Version match riskLow if confirmedMediumNone (same board)
ReliabilityHighVariableVariable; depends on damage
WarrantyUsually offeredShort or noneShort
TurnaroundFast if in stockFast if in stockDays to weeks
Best forMain production machinesBackup machines, obsolete versionsLimited damage, obsolete or locked boards

The true cost: more than the board price

The real cost of a board decision includes downtime, labour, related parts and risk to heads. Consider an example for a double-head i3200 machine producing steady daily work. The figures are illustrative; plug in your own numbers.

Cost elementNew boardRefurbished boardRepair own board
Board or repair cost₹35,000₹20,000₹8,000
Head cables and adapters₹3,000₹3,000₹3,000
Technician and installation₹4,000₹4,000₹4,000
Downtime (days)227
Lost gross margin at ₹6,000/day₹12,000₹12,000₹42,000
Total visible cost₹54,000₹39,000₹57,000

In this example, repair looks cheapest at first but becomes the most expensive once downtime is counted, unless you have a backup board or another machine to cover the work. The refurbished option looks best on paper, but if it fails early or damages a head worth ₹35,000 to ₹45,000, the picture changes completely. The point is not that one option is always best, but that you should include downtime and risk in the comparison. Our repair vs replace decision guide explains this way of thinking in more detail.

The risk factor: protecting your printheads

A carriage board directly drives printheads that often cost more than the board itself. A board with a weak or faulty drive section can damage new heads. When comparing a ₹15,000 saving on a cheaper board, remember that one damaged i3200 head can wipe out that saving several times over. This is why many shop owners choose new or well-tested boards for their main production machine, and use refurbished or repaired boards only where the risk is acceptable.

Keeping a spare board: is it worth it?

For shops that depend heavily on one eco-solvent machine, a spare carriage board can be worth considering. If your machine earns several thousand rupees of margin per day, a week of downtime waiting for a board can cost more than the board itself. Options include keeping a new spare board, keeping your old repaired board as a backup after replacement, or agreeing with your supplier to hold stock for you. A spare also allows quick diagnosis: swapping a known-good board (with proper precautions) can confirm a fault in minutes. Our spare parts inventory guide discusses which spares are worth keeping.

Local supplier, online marketplace or direct import?

Indian shop owners usually buy boards through one of three routes. Each has a different balance of price, speed and support.

RoutePriceSpeedSupport and warrantyBest for
Machine supplier or local spare parts dealerMedium to higherFast if in stockBest chance of version confirmation, installation help and local warrantyMain production machines, locked boards
Online B2B marketplaces and listing sitesVaries widelyDepends on sellerVaries; check seller history, GST invoice and return policyCommon boards when you can confirm version yourself
Direct import from overseas sellersOften lowest board priceSlowest: shipping and customsLimited; returns are difficult and costlyExperienced buyers with spare machines or planned upgrades

A low import price can rise significantly once freight, customs duty, GST and payment charges are added, and a wrong or faulty board is hard to return. For an urgent breakdown on your only machine, a reliable local supplier is usually the better value even at a higher price, because days of downtime cost more than the price difference.

Hidden costs to include in your budget

When budgeting for a board replacement, include these often-forgotten items:

  • New head cables and adapter boards, which are frequently damaged along with the board.
  • A replacement printhead if the head was involved in the failure.
  • Technician time for diagnosis, not just installation.
  • Activation or licence fees on locked systems.
  • Media and ink used for calibration and test prints.
  • Fixing the root cause: dampers, tubes, stabiliser or earthing work.
  • Lost production during downtime, and any rush delivery charges.

Adding these items early prevents a ₹20,000 board job from quietly becoming a ₹60,000 repair without anyone noticing until the bills arrive.

Red flags in board quotes

  • Price far below the market range with no clear explanation.
  • Seller cannot confirm the exact version from your photos.
  • No mention of whether the board is new, refurbished or repaired.
  • No warranty, or warranty that excludes nearly everything.
  • Seller says any board “for i3200” will work, regardless of brand or version.
  • No support offered for firmware, voltage setting or activation.
  • Pressure to pay fully in advance with no invoice or GST bill.

Our guides on genuine vs compatible parts and comparing spare parts suppliers provide more detailed checks.

How to get an accurate quote

Send your supplier:

  1. Printer make, model and width.
  2. Clear photos of the current carriage board, both sides, with all labels visible.
  3. Photo of the mainboard label.
  4. Head type and number of heads.
  5. Firmware and software version screenshots.
  6. Description of the fault and what has been checked.
  7. Whether you need installation, calibration and activation.

Ask for a written quote that states the board brand, model, version, condition (new, refurbished, repaired), inclusions, warranty period and terms, delivery time and GST. This makes it easy to compare offers fairly.

GST, invoices and warranty documentation

Always ask for a proper GST invoice. Besides being required for business accounting and input tax credit, it is your proof of purchase for warranty claims. Keep the invoice with photos of the installed board, its labels and the installation record. If a board fails under warranty, suppliers usually ask for this information.

When a board price suggests a bigger decision

If your machine is old, uses an obsolete board system, and needs a board that is expensive or hard to find, the board price can be a signal to consider a bigger decision: a complete kit upgrade or a newer machine. Compare the cost of the board plus likely further repairs with the cost of a full kit upgrade or a new machine with warranty. Our articles on single to double head upgrades and eco-solvent printer prices in India help with that comparison.

Further reading: When comparing quotes, insist on a proper tax invoice; the official GST portal lets you verify a supplier’s GSTIN.

Key takeaways

  • Indicative new carriage board prices in India range from about ₹10,000 for basic single-head XP600 boards to ₹45,000 or more for double-head i3200 boards, before GST.
  • Complete kits run from about ₹28,000 to ₹70,000, and kits with heads can exceed ₹1,00,000.
  • Refurbished boards save money but carry more risk; repair is cheapest but slowest.
  • Include downtime, labour, cables and risk to printheads when comparing options.
  • Get written quotes with exact version, condition, inclusions and warranty, and always insist on a GST invoice.

Unified Engineering Dynamics can quote matched carriage boards and complete kits for common eco-solvent printers, confirm compatibility from your photos, and help you compare new, refurbished and repair options for your situation.

More in the head carriage board series

Related: our fire board series explains the firing circuit that drives the heads, starting with What Is a Fire Board?, plus fire board failure signs and head voltage settings.

Related: our main board series covers main board functions and failure points, main board failure symptoms, the main board replacement checklist and how lightning, surges and earthing faults damage main boards.

For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.

Frequently Asked Questions

What is the price of an i3200 head board in India?

Indicatively, a single-head i3200 carriage board costs about ₹14,000 to ₹28,000 and a double-head board about ₹22,000 to ₹45,000 before GST, depending on brand, version and supplier. Always get a current written quote for your exact version.

Is a refurbished head board a good idea?

It can be, if the supplier is reliable, the board is tested with the correct head type and a warranty is offered. For main production machines with expensive new heads, a new board is usually the safer choice.

How much does head board repair cost?

Board-level repair commonly costs from a few thousand rupees up to around ₹12,000, depending on the damage. Heavily corroded or badly burned boards may not be repairable.

Why do prices for the same board vary so much?

Differences in authenticity, version, condition, supplier type, import costs, included parts and warranty all affect price. Compare quotes on the same basis.

Should I buy a complete kit instead of just a carriage board?

Only if your board version is obsolete, you are changing heads or head count, or the mainboard is also faulty. For a simple failure with an available matching board, a single board replacement is usually cheaper.

Do board prices include installation?

Usually not. Installation, calibration and activation are often charged separately. Ask for these to be listed clearly in the quote.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *