Direct answer: When the print control software cannot find an eco-solvent printer, or the connection drops during printing, the main board’s network or USB port is rarely the first culprit. Most connection problems come from the PC side and can be fixed by operators: a loose or damaged cable, the PC’s network adapter set to the wrong IP address range after a Windows update, firewall or antivirus blocking the software, Windows power saving switching off the network adapter or USB port, a router or switch in between causing conflicts, or a long or poor-quality USB cable. Operators can check link lights, replace the cable with a short known-good one, verify the PC’s network settings against the installation record, allow the software through the firewall, disable power saving, and connect the printer directly to a dedicated network port. If the link lights stay off with a known-good cable and PC, especially after a storm, the board’s port may be damaged and a technician is needed.
Most network and USB problems on eco-solvent printers start on the PC side, which is good news for operators.

Table of Contents
This guide gives a step-by-step approach for both network-connected and USB-connected printers. It is part of our main board series; for broader symptoms see main board failure symptoms.
Before you start: record your working setup
The single most useful thing you can have is a record of how the connection was set up when it worked. At installation, or now if it is working, record:
- Connection type: network or USB.
- For network: the printer’s IP address, the PC network adapter’s IP address and subnet mask, and which PC port the printer cable uses.
- For USB: which USB port is used and the driver version.
- Print control software version and installation folder.
- Firewall and antivirus exceptions that were added.
Write this on a card and keep it near the PC. Many connection problems are solved in minutes by comparing current settings with this record.
How network connection usually works
Many current eco-solvent board kits connect to the PC with a standard network cable. The printer’s main board has a fixed IP address set by the board maker or machine supplier. The PC’s network adapter must be set to an address in the same range, so they can talk to each other. Usually the printer is connected directly to a dedicated network port on the PC, not through the shop’s internet router. The print control software then finds the printer at its IP address.
If the PC’s address changes, for example because Windows switched the adapter to automatic addressing after an update, or because someone connected the printer cable to the port used for internet, the software can no longer find the printer.
Step-by-step network checks
Step 1: Restart properly
Close the print control software, switch off the printer, wait at least a minute, switch it on and wait for initialisation, then restart the PC and open the software. Many temporary glitches clear this way.
Step 2: Check link lights
Look at the network port on the printer and on the PC. Most ports have small lights that show a link and activity. If the lights are off on both ends with the printer powered on, the problem is the cable, a port, or the printer not powering its network circuit.
Step 3: Replace the cable
Use a short, good-quality network cable (Cat5e or Cat6) known to work. Plug it directly between the printer and the PC’s dedicated port. Network cables in print shops are often stepped on, pinched by doors or chewed by rodents. A cable that looks fine can still be broken inside.
Step 4: Check the PC’s network adapter settings
Open the network adapter settings on the PC and check the IPv4 settings for the adapter connected to the printer. Compare the IP address and subnet mask with your installation record. If they have changed to “obtain automatically” or a different address, set them back to the recorded values. If you do not have a record, ask your machine supplier for the printer’s IP address and the recommended PC settings.
Step 5: Check the right port is used
If the PC has two network ports, one for the internet and one for the printer, make sure the printer cable is in the port configured for the printer. Swapping cables between ports is a common cause of sudden connection failures.
Step 6: Check firewall and antivirus
Windows Firewall or third-party antivirus can block the print control software, especially after updates. Make sure the software is allowed through the firewall on the relevant network. If you are unsure, ask your IT person or supplier for help rather than turning off protection entirely.
Step 7: Remove intermediate devices
If the printer is connected through a switch, router or Wi-Fi bridge, connect it directly to the PC to test. Routers can assign conflicting addresses, and cheap switches can drop data under load, causing mid-print disconnections.
Step 8: Disable power saving on the network adapter
Windows can switch off network adapters to save power. In the adapter’s properties, under power management, disable the option that allows the computer to turn off the device to save power. Also set the PC’s power plan so it does not sleep during printing.
Step 9: Test with ping (optional)
If you are comfortable using the command prompt, you can ping the printer’s IP address. Replies indicate the network link works and the problem is likely in the software or firewall. No replies indicate a cable, setting or port problem.
Step 10: Try another PC
If another PC with the print control software is available, configure its adapter with the same settings and connect it. If it connects, the original PC is the problem. If it does not, the printer side is more likely.
Step-by-step checks for USB problems
Step 1: Restart properly
As above, fully switch off the printer and restart the PC.
Step 2: Check the cable
Use a short, good-quality USB cable. Long cables, cheap cables and USB extension cables commonly cause dropouts. Avoid USB hubs between PC and printer.
Step 3: Try another USB port
Use a USB port directly on the PC’s motherboard, usually at the back of a desktop PC, rather than front panel ports. Some ports provide less stable power or signal.
Step 4: Check Device Manager
Open Device Manager and see whether the printer’s USB device appears when connected. A device with a warning symbol suggests a driver problem. No device at all suggests a cable, port or printer-side problem.
Step 5: Reinstall drivers
Reinstall the USB driver provided with the print control software, following the supplier’s instructions.
Step 6: Disable USB power saving
In Windows power options, disable USB selective suspend, and in Device Manager disable power saving for USB root hubs. This prevents Windows from cutting power to the port during printing.
Step 7: Never hot-plug during operation
Connect or disconnect the USB cable only when the software is closed and, preferably, the printer is off. Hot-plugging during operation can corrupt communication and, in rare cases, damage ports.
Common causes and fixes
| Symptom | Likely cause | Fix |
|---|---|---|
| Software cannot find printer after Windows update | Adapter settings changed or firewall rules reset | Restore IP settings, re-allow software in firewall |
| Connection drops mid-print | Power saving, poor cable, switch or router, PC sleep | Disable power saving, direct short cable, remove intermediate devices |
| No link lights | Damaged cable, port, or printer not powered | Replace cable, check other port, check printer power |
| Works on one PC but not another | PC settings or software installation | Compare settings, reinstall software |
| USB device not recognised | Cable, port, driver | Short cable, rear port, reinstall driver |
| Random disconnects when heavy equipment starts | Power disturbance, earthing, interference | Check earthing and power protection; route cables away from power cables |
| Connection lost after storm | Surge damage to PC or printer port | Test with another PC; technician check of ports |
Windows changes that commonly break the connection
Many sudden connection failures follow a Windows change rather than a hardware fault. Watch for these after any update or new software installation:
- Network adapter switched back to automatic IP addressing.
- Network profile changed from private to public, with stricter firewall rules.
- Firewall rules reset, removing the exception for the print control software.
- New antivirus or security software quarantining parts of the print software.
- Power plan reset, re-enabling sleep and USB power saving.
- Network adapter driver updated to a version with different power management defaults.
Checking these points first after a Windows update saves a lot of unnecessary troubleshooting.
Protecting network cables in the shop
The network cable between PC and printer is simple but vulnerable. Keep it short and direct, route it along walls or inside conduit rather than across walkways, and keep it away from heater and motor power cables to reduce interference. Avoid sharp bends and pinch points under doors or furniture. In shops with rodent problems, protect cables with conduit. If the PC must be some distance from the printer, use a good-quality shielded cable and consider surge protection for the network line, because long cables can pick up surges during storms.
Remote support
Many suppliers can help with connection and software problems remotely, using remote desktop tools on the printing PC. To make this possible, keep the PC connected to the internet through a separate network port or Wi-Fi, so the printer link remains on its own dedicated port. Have the remote support tool installed in advance and know how to start it. Remote support can resolve many configuration problems within minutes, without waiting for a technician visit.
Earthing and interference
When the PC and printer are plugged into different sockets with different earth quality, or when earthing is poor, small voltage differences between them can disturb communication and, during surges, damage ports. Plug the PC and printer into sockets on the same protected supply, ideally the same UPS, with a proper earth. Route network and USB cables away from heater and motor power cables. Our guide to stabiliser, UPS and earthing explains the basics.
Keep the PC dedicated and stable
The PC that runs the print control software is part of the printing system. To keep connections reliable:
- Use the PC mainly for printing and RIP work, not general browsing and downloads.
- Control Windows updates so they do not install and restart during production.
- Keep antivirus exceptions for the print software and RIP.
- Avoid installing unnecessary software that changes network settings.
- Keep a backup of the print software installer and settings.
When it is a main board port problem
Suspect the main board’s communication port when:
- Link lights stay off at the printer with a known-good cable, and the printer otherwise powers up.
- Another PC with correct settings also cannot connect.
- The problem started after a storm, surge or electrical event.
- The port is physically damaged or loose.
In these cases, call a technician. The port may be repairable at board level, or the main board may need replacement. Our articles on main board failure points and lightning and surge damage explain what happens next.
What to tell the technician or supplier
If you need help, provide this information so the problem can be diagnosed quickly, often remotely:
- Connection type (network or USB) and when the problem started.
- Any recent changes: Windows updates, new software, new PC, moved machine, storm or power event.
- State of link lights on both ends.
- Current PC adapter IP settings, compared with your installation record.
- Results of cable swaps, port swaps and testing another PC.
- Exact error messages, with screenshots.
- Whether the printer otherwise powers up and initialises normally.
This information lets the supplier separate PC-side issues from main board faults and avoids unnecessary visits and part replacements.
Preventing connection problems
A few habits keep connections reliable: keep the installation record up to date, control Windows updates, keep a spare known-good network or USB cable near the PC, plug PC and printer into the same protected and earthed supply, and avoid moving cables during printing. Review the connection set-up whenever the PC is replaced or reinstalled.
Operator connection checklist
| # | Check | Done |
|---|---|---|
| 1 | Full restart of printer and PC | ☐ |
| 2 | Link lights checked (network) or device seen in Device Manager (USB) | ☐ |
| 3 | Short known-good cable connected directly | ☐ |
| 4 | PC adapter settings match installation record | ☐ |
| 5 | Correct PC port used | ☐ |
| 6 | Software allowed through firewall and antivirus | ☐ |
| 7 | No router, switch or hub in between | ☐ |
| 8 | Power saving disabled for adapter and USB; PC sleep off | ☐ |
| 9 | Another PC tested if available | ☐ |
| 10 | Technician called if all checks fail | ☐ |
Further reading: Most current board kits use standard Ethernet networking between the PC and the printer.
Key takeaways
- Most printer connection problems are PC-side and can be fixed by operators.
- Keep a record of the working IP settings, ports and software versions.
- Use short, good cables connected directly, and avoid routers, switches and hubs in between.
- Restore adapter settings after Windows updates, allow the software through the firewall and disable power saving.
- Suspect the main board port only when known-good cables and PCs fail, especially after a storm.
If your printer still will not connect after these checks, the Unified Engineering Dynamics team can help diagnose the port and main board and arrange repair or replacement.
More in the main board series
This article is part of our series on eco-solvent printer main boards. Continue with the other guides:
- Eco-Solvent Printer Main Board: Functions, Ports and Common Failure Points
- Main Board Failure Symptoms: No Connection to PC, Carriage Not Moving, Error Codes
- Hoson vs Senyang vs BYHX Main Boards: Which Board Kit Suits Your Printer?
- Main Board Firmware Updates: When to Update, Risks and Backup Steps
- Board Kit Upgrade: Converting an XP600 Printer to i3200 (Main + Head Board Changes)
- Main Board Replacement Checklist: Dongle, Software Licence, Maintop/PhotoPrint Settings
- Lightning, Surges and Earthing Faults: Why Main Boards Die in Monsoon Season
- Eco-Solvent Main Board Price in India: XP600, i3200, DX5 Kits Compared
- Buying a Second-Hand Eco-Solvent Printer? How to Check the Main Board and Electronics
Related: our head carriage board series starts with the head carriage board explained, and our fire board series starts with what a fire board is and what it does. For a side-by-side view of all three boards, read fire board vs head board vs mainboard.
For a system-wide view, see our complete guide to eco-solvent printer electronics, our step-by-step electronics fault isolation guide and the monthly electronics maintenance checklist.
Frequently Asked Questions
Why can my print software not find the printer?
Common causes are a changed PC network setting, firewall or antivirus blocking, a damaged cable, the wrong PC port, or power saving. Restore settings and test with a short known-good cable.
How do I find my printer’s IP address?
Check your installation record, the machine manual, or ask your machine supplier. The PC’s network adapter must be set to the same address range.
Why does my printer disconnect in the middle of printing?
Typical causes are Windows power saving, PC sleep, poor cables, a router or switch in between, or power and earthing disturbances.
Can I connect the printer through my shop’s router?
It is usually better to connect directly to a dedicated network port on the PC. Routers can assign conflicting addresses and add instability.
Is a long USB cable a problem?
Yes. Long or low-quality USB cables and extension cables commonly cause dropouts. Use a short, good-quality cable in a rear PC port.
When should I suspect the main board?
When link lights stay off with a known-good cable, another PC cannot connect either, or the problem started after a storm or surge.