Direct answer: Eco-solvent printer boards are compatible only within a matched kit. A main board, head carriage board, firmware and print control software are designed together for a specific head family (such as XP600, i3200, DX5 or DX7) and a specific head count. In general, you cannot fit an i3200 head on an XP600 board, use a DX5 carriage board with an XP600 main board, or mix board brands such as Hoson and Senyang within one machine. Even within one brand and head family, board version and firmware must match. What can sometimes vary is the head count within the same family (for example, one or two XP600 heads) if the main board supports it and the right carriage board is used. Before buying any board, record the brand, model, version and firmware of both boards and the head type and count, and get written confirmation of compatibility from the supplier.
Use this board compatibility table as general guidance, then confirm your exact boards with the supplier.

Table of Contents
This guide summarises compatibility in tables, explains what must match and why, and gives a checklist for confirming compatibility. Board and firmware versions change often, so treat these tables as general guidance and always confirm with your supplier. It is part of our final printer electronics section; see also our complete electronics guide.
Why boards are so specific
Different printhead families differ in nozzle count, nozzle layout, data format, drive waveform, voltage requirements, connectors and cabling. The fire stage must produce the right waveform for the head; the carriage board must have the right connectors and data handling; the main board must process data at the right rate and in the right format; and firmware and software must know the head’s layout. Change the head family and almost every part of this chain changes. Our article on fire board compatibility explains the waveform side.
Head families at a glance
| Head family | Typical use in eco-solvent | Board kit situation |
|---|---|---|
| XP600 | Entry-level machines, single or double head | Widely available kits from several board makers |
| i3200 (eco-solvent variant) | Production machines, higher speed | Dedicated i3200 kits; often uses adapter boards |
| DX5 | Older high-quality machines | Kits exist, but availability varies; some systems older |
| DX7 | Some older machines | Less common; availability varies |
For more about the heads themselves, see our comparison of i3200 vs XP600 and our XP600 vs i3200 machine guide.
Cross-family board compatibility table
This table shows whether a board designed for one head family can generally be used with another. “No” means not without a complete kit change.
| Board designed for → Head fitted ↓ | XP600 kit | i3200 kit | DX5 kit | DX7 kit |
|---|---|---|---|---|
| XP600 | Yes (correct version and head count) | No | No | No |
| i3200 | No | Yes (correct version and head count) | No | No |
| DX5 | No | No | Yes (correct version) | Generally no; confirm with supplier |
| DX7 | No | No | Generally no; confirm with supplier | Yes (correct version) |
Some board systems offer main boards that support several head families with different carriage boards and firmware. Where this exists, it applies only to specific models and versions and must be confirmed by the board maker or supplier.
Within one head family: what must match
| Item | Must match? | Notes |
|---|---|---|
| Board brand (Hoson, Senyang, BYHX, other) | Yes | Main and carriage boards from different brands do not communicate |
| Main board model and version | Yes, or approved newer version | Newer versions may need matching carriage board or firmware |
| Carriage board model and head count | Yes | Single, double, four-head boards differ |
| Main board firmware | Must match carriage board and software | See firmware guide |
| Carriage board firmware | Must match main board | Often updated together |
| Print control software version | Must match firmware | Newer software may require newer firmware |
| Data cable type and length | Yes | Wrong cable can cause errors or damage |
| Head cables and adapter boards | Yes | Correct type for head and board |
| Machine lock or activation | Yes | Locked boards need maker’s activation |
Our guides to main board kits, carriage board compatibility and firmware updates explain each item.
Changing head count within a family
| Change | Usually needed | Watch out for |
|---|---|---|
| 1 → 2 XP600 | Two-head carriage board, possibly main board support or upgrade, firmware, head plate, capping, dampers, ink lines | Main board support; PSU capacity; alignment |
| 2 → 1 XP600 | Software reconfiguration; sometimes carriage board change | Usually done for cost or repair reasons |
| 1 → 2 i3200 | Two-head i3200 carriage board, firmware, adapters, mechanics, ink system | Carriage load, PSU, heater capacity |
| 2 → 4 heads | Four-head board set, major mechanical and ink changes | Often better as a new machine |
See our guide on single to double head upgrades.
Changing head family
Moving from one head family to another, for example XP600 to i3200, means a complete board kit change plus mechanical and ink system changes. It is a conversion project, not a spare part purchase. Our XP600 to i3200 conversion guide explains the scope and costs.
Board brand compatibility summary
The main board makers used in eco-solvent machines each offer kits for several head families. The table below is a general orientation; exact models, versions and support change over time, so always confirm details with your supplier.
| Board brand | Head families commonly supported | Compatibility notes |
|---|---|---|
| Hoson | XP600, i3200, DX5 and others, in single and multi-head kits | Very common in Indian market machines; many versions exist, so version matching is essential |
| Senyang | XP600, i3200, DX5 and others | Widely used; kits not interchangeable with Hoson |
| BYHX | Various heads, often in higher-end or industrial systems | Often supplied through machine makers with their own configuration |
| Machine maker’s own boards | Heads chosen by that maker | May be locked; replacements usually through the maker |
Within each brand, multi-head kits and different board generations may use different carriage boards, cables and firmware. Treat brand as the first filter, then model, version and head count.
Compatibility of printheads within a family
Even within one head family, there are variants. For example, i3200 heads come in variants intended for different ink types, and an eco-solvent machine needs the eco-solvent variant. XP600 heads may come as new original, new compatible or refurbished units. Ink compatibility, head variant and head quality all affect performance and life, even when the board kit is correct. Our guides on printhead ink compatibility, genuine vs compatible printheads and new vs refurbished printheads explain the differences.
Compatibility of firmware and software versions
Firmware and software versions form their own compatibility layer:
| Scenario | Likely result | Action |
|---|---|---|
| Same main board, older carriage board firmware | Communication errors or missing features | Update carriage board firmware as advised |
| New main board, old PC software | Software may not recognise board | Install matching software version |
| New software, old firmware | Errors or refusal to connect | Update firmware or use matching software |
| Firmware for different head count | Heads not detected or wrong layout | Load firmware for correct configuration |
| Firmware from another machine | Unpredictable behaviour, possible damage | Never use; get correct file from supplier |
Keep a record of firmware and software versions and always update them together as your supplier advises. Our firmware update guide explains a safe procedure.
Common compatibility mistakes
- Buying by brand name only: “Hoson XP600 board” can mean several models and versions.
- Ignoring head count: a single-head carriage board will not drive two heads.
- Ignoring firmware: a replacement board with different firmware may not communicate.
- Assuming same-looking boards are the same: layouts can be similar while versions differ.
- Using the wrong data cable: wrong type or length causes errors.
- Forgetting locks: machine-maker boards may need activation.
- Mixing brands to save money: it almost never works.
Cable and connector compatibility details
| Part | What varies | Risk if wrong |
|---|---|---|
| Head cable | Head family, pin count, length, connector orientation | Heads not detected, damaged channels, burnt connectors |
| Data cable | Board system, cable type, length, shielding | Communication errors, data loss, intermittent faults |
| Adapter or transfer board | Head family, carriage board model | Heads not detected, wrong signals |
| Power cable to carriage board | Voltage, connector, wire gauge | Board damage, overheating |
| Encoder sensor cable | Connector, length | Carriage errors, banding |
Cables that look similar can have different pin assignments or lengths. A head cable that is too long may cause signal problems; one that is too short may be strained in the cable chain. Always match the existing cable exactly or follow the supplier’s specification.
Why “universal” boards and parts need caution
Some sellers advertise boards or cables as “universal” or “fits all XP600 machines”. In practice, compatibility depends on the board system, version and machine configuration. A universal claim is not a substitute for checking brand, model, version, head count and firmware. If a seller cannot answer specific compatibility questions, choose another supplier.
Compatibility after machine modifications
If your machine has been modified, for example converted from one head family to another or upgraded from one to two heads, the original machine documentation may no longer describe the installed boards. Always identify what is actually installed rather than relying on the machine model name. Record the changes in your machine file so future spare purchases are based on the current configuration.
How to identify your boards
- With the machine off and disconnected, open the electronics compartment (technician recommended).
- Photograph the main board, including labels, model codes and connectors.
- Photograph the carriage board and any adapter boards.
- Record firmware and software versions from the print control software.
- Record head type, head count and head labels.
- Record machine model and serial number.
Our article on identifying spares by model and part number gives more tips.
Compatibility confirmation checklist
| # | Item to send the supplier | Done |
|---|---|---|
| 1 | Main board photos, brand, model, version | ☐ |
| 2 | Carriage board photos, model, head count | ☐ |
| 3 | Adapter boards and cable types | ☐ |
| 4 | Firmware and software versions | ☐ |
| 5 | Head type, count and labels | ☐ |
| 6 | Machine model and serial number | ☐ |
| 7 | Lock or activation status | ☐ |
| 8 | Written confirmation of compatibility received | ☐ |
Example compatibility scenarios
Scenario 1: A shop with a single-head XP600 machine on a Hoson kit needs a new carriage board. The shop sends photos of the main board label, carriage board label and firmware version. The supplier confirms the same carriage board model and version is available with matching firmware. Installation is straightforward.
Scenario 2: A shop buys a “Hoson XP600 head board” online at a low price. It arrives as a different version from the main board installed, and the machine reports communication errors. The board must be returned or the main board firmware updated, causing delay. Confirming the version beforehand would have avoided this.
Scenario 3: A shop wants to fit i3200 heads to an XP600 machine by changing only the head board. The supplier explains that a full i3200 kit is required, along with mechanical changes. The shop compares the total cost with a new i3200 machine before deciding.
These illustrative scenarios show that the few minutes spent identifying boards and confirming compatibility save days of downtime.
Compatibility and warranty
Installing an incompatible board, or a correct board with wrong firmware or settings, can damage boards and heads and may void warranties. Keep the supplier’s written compatibility confirmation with your invoice. Our guide to board warranty claims explains what typically voids warranty.
Questions to ask before buying any board
- Is this the same brand, model and version as my installed board, or an approved replacement?
- Is it for my head family and head count?
- Which firmware is loaded, and does it match my other board and software?
- Are the correct cables and adapters included or required separately?
- Is activation required, and who provides it?
- Will you confirm compatibility in writing, and accept a return if it does not fit?
Compatibility of cables and small parts
Cables, adapter boards and small electronic parts follow the same logic. Head cables differ by head family, length and connector type; data cables differ by board system; adapter boards are specific to head and carriage board. Keep the part numbers or photos of your existing cables, and buy replacements matched to them. See our guide to data and printhead cables.
Quick decision guide
| Your situation | What to buy |
|---|---|
| Head board failed, same heads | Same brand, model, version and head count carriage board; confirm firmware |
| Main board failed, same heads | Same brand, model and version main board, or supplier-approved newer version with matching firmware |
| Want more heads, same family | Multi-head carriage board, confirmed main board support, mechanical and ink parts |
| Want different head family | Complete new board kit plus conversion parts, or new machine |
| Older system, parts scarce | Consider spare boards now, repair options, or a planned kit upgrade |
| Used machine purchase | Check board system support status before buying |
For older systems where parts are becoming scarce, our guide to building an electronics spares inventory and our second-hand printer electronics check are useful next reads.
Keep a compatibility record for each machine
Create a one-page compatibility record for each machine listing the board brand, main board model and version, carriage board model and head count, adapter boards, cable types and lengths, firmware and software versions, head type and variant, and lock status. Update it whenever anything changes. With this page, ordering the right spare becomes a two-minute task, and any supplier can confirm compatibility quickly.
Further reading: Boards that look alike can carry different versions; small printed circuit board revisions often change compatibility.
Key takeaways
- Boards are compatible only within a matched kit for a specific head family and head count.
- Cross-family use (XP600, i3200, DX5, DX7) generally requires a complete kit change.
- Within a family, brand, model, version, firmware, software and cables must match.
- Head count changes need the right carriage board and often main board support.
- Identify your boards precisely and get written confirmation before buying.
Send the Unified Engineering Dynamics team photos of your boards and your head configuration, and we will confirm compatibility and recommend the right parts.
More in the printer electronics series
This article is part of our final section on eco-solvent printer electronics as a whole system. Continue with the other guides in this section:
- Eco-Solvent Printer Electronics: The Complete Guide to Main Board, Head Board, Fire Board and Power Supply
- Electronics Fault Isolation: Is It the Main Board, Head Board, Cable or Printhead?
- Building an Electronics Spares Inventory: What Boards and Cables a Print Shop Should Stock
- Warranty Claims on Printer Boards: What Voids Warranty and How to Document Failures
- Monthly Preventive Maintenance for Printer Electronics: A Simple Checklist
Related: for detailed coverage of each board, start with our three board series: the head carriage board explained, what a fire board is and what it does, and main board functions, ports and failure points.
Frequently Asked Questions
Can I use an XP600 board with an i3200 head?
No. i3200 heads need a dedicated i3200 board kit, including carriage board, main board support, firmware and cables.
Can I mix a Hoson main board with a Senyang carriage board?
No. Main and carriage boards from different brands do not communicate. Use a matched kit from one brand.
Will a newer version of my board work as a replacement?
Sometimes, but it may need matching firmware or a matching carriage board. Confirm with the supplier before buying.
Can I go from one to two XP600 heads by changing the head board?
Only if your main board supports two heads with the correct carriage board and firmware. Mechanical, capping and ink changes are also needed.
Are DX5 and DX7 boards interchangeable?
Generally not. Confirm with your supplier for your specific board system.
What should I send a supplier to confirm compatibility?
Photos and models of both boards, firmware and software versions, head type and count, cable types, machine model and serial number, and lock status.