UV Printing

UV Flatbed i3200 Head Change: Why Head Boards Burn and How to Fit an i3200-U1 Head Safely

UV Flatbed i3200 Head Change Without Burning the Head Board

Direct answer: A UV flatbed i3200 head change burns the head board when a cable is plugged or unplugged with power on, a ribbon cable is inserted at an angle or one pin off, a damaged or shorted head is fitted, ink leaks onto connectors during the change, the wrong voltage is entered, or static from the operator or substrate discharges into the head. To change an i3200-U1 head safely, switch off and isolate power, use an anti-static strap, inspect the new head and cables, insert cables straight and fully, prime and check for leaks before power-up, enter the voltage from the head label, then test one head at a time. Following these steps protects a head worth about โ‚น78,000โ€“95,000 and a carriage board worth hundreds of dollars.

A careless UV flatbed i3200 head change can burn a head worth about โ‚น78,000โ€“95,000 and the board behind it within seconds.

UV Flatbed i3200 Head Change Without Burning the Head Board
UV Flatbed i3200 Head Change Without Burning the Head Board

Epson i3200-U1 heads are now the most popular choice on A3, A2 and 6090 UV flatbeds because of their speed and resolution. They are also expensive and sensitive. This guide explains why head changes go wrong and how to do them safely. It builds on our carriage board replacement checklist.

About the i3200-U1 on UV flatbeds

The i3200-U1 is the UV-ink version of Epson’s i3200 head family. It has four rows of nozzles and is used for CMYK, white or varnish depending on the layout. Indian listings in 2026 priced genuine i3200-U1 heads at about โ‚น78,000โ€“95,000, compared with about โ‚น12,000โ€“15,000 for an XP600. See our i3200 vs XP600 comparison.

Using the wrong head variant matters: the i3200-U1 is intended for UV ink, while A1 and E1 variants are intended for water-based and eco-solvent inks. Fitting the wrong variant on a UV flatbed shortens head life.

Why head boards burn during head changes

CauseWhat happens
Hot-pluggingConnecting or disconnecting with power on causes voltage spikes that damage the driver channel and head
Angled or offset cableAdjacent pins short, sending drive voltage to the wrong pins
Shorted headA damaged head draws excessive current and burns the channel
Ink on connectorsUV ink bridges pins, causing shorts
Wrong voltageOverdriving the head shortens its life; very wrong settings can cause damage
Static dischargeOperator or acrylic sheets discharge into exposed pins
Wrong head variantReduced compatibility and life with UV inks

Before the head change

  1. Find out why the old head failed. If it was electrical, have the board channel tested first.
  2. Check the new head. Confirm it is genuine i3200-U1, inspect the nozzle plate and connectors, and note the voltage on the label.
  3. Check cables. Replace any cable that was connected to a failed head or shows damage.
  4. Back up settings. Record head voltages, temperatures, alignment and offsets.
  5. Prepare the area. Lint-free cloths, gloves, cleaning fluid compatible with your ink, anti-static strap, torch and magnifier.

Step-by-step head change

  1. Switch off the printer and disconnect mains power. Switch off lamps.
  2. Wait for the recommended discharge time.
  3. Wear an anti-static strap connected to machine earth.
  4. Close ink valves or clamp lines to the old head.
  5. Remove the carriage cover carefully.
  6. Disconnect the old head’s cables, pulling straight out after releasing locks.
  7. Remove the damper connections and the head mounting screws.
  8. Clean the mounting area and check for ink on the carriage board below.
  9. Fit the new head, tightening screws evenly without overtightening.
  10. Connect dampers and check for leaks.
  11. Inspect cable ends, then insert cables straight and fully, with correct orientation, and close the locks. Check under good light.
  12. Prime the head with ink and inspect for leaks with power still off.
  13. Refit covers, restore power and start the software.
  14. Enter the new head’s voltage from the label.
  15. Check detection and temperature, then run a nozzle check.
  16. Align the head mechanically and in software, and calibrate.

Priming and leak checks

UV ink leaking from a loose damper or line during priming can run onto connectors and the board. Always prime with power off, wipe away any spills, and check connections again before powering up. Cured UV ink on connectors is hard to remove and can cause intermittent faults.

Head voltage and temperature

Each i3200-U1 head carries a recommended voltage on its label. Enter it exactly in the print control software for that head channel. Set head temperature according to your ink maker’s guidance. See i3200-U1 head voltage settings.

If the new head does not work

SymptomCheck
Head not detectedCable orientation, seating, locks, cable damage, firmware
Missing rowsPriming, air, nozzle plate, cable seating
Temperature errorHeater connector, setting
Overcurrent errorSwitch off immediately; check cable and head
Burning smellSwitch off immediately; inspect board and cables

Static control during head changes

UV flatbed shops often handle acrylic and PVC sheets that build strong static. Before touching a head or board, touch earthed machine metal and wear an anti-static strap. Keep new heads in their anti-static packaging until fitting. Avoid working near freshly peeled acrylic. See board connectors and static handling.

Genuine vs refurbished heads

Refurbished or decrypted heads are sometimes offered at lower prices. Some are fine, but others have damaged nozzles or internal faults that can short a board channel. Buy from trusted suppliers and ask for test prints and warranty terms. Our guide to genuine and compatible parts identification explains what to check.

Example: hot-plug disaster

An operator in Noida reseated a white head cable with the machine on to fix an intermittent fault. The head and the white channel burnt instantly. The repair cost a new i3200-U1 head, a cable and a carriage board. A thirty-second shutdown would have prevented it.

Example: offset cable

A technician fitted a new head, but one cable was inserted one pin off. The head showed an overcurrent error. He switched off immediately, reinserted the cable correctly, and the head worked. Quick action saved the head and board.

Tools for a UV flatbed i3200 head change

Tool or supplyPurpose
Anti-static wrist strapPrevents static damage to head and board
Screwdrivers of correct sizeAvoid stripping head mounting screws
Nitrile glovesProtect skin from UV ink
Lint-free cloths and swabsClean nozzle area and spills
Cleaning fluid compatible with your inkRemove uncured ink
Syringe and tubingPrime the head
Bright torch and magnifierCheck cable insertion
Calipers or feeler gaugesCheck head height
Masking tape and markerLabel cables and lines
Phone cameraPhotograph connections before removal

UV inks can irritate skin and eyes. Follow the safety advice in our UV ink handling and operator safety guide.

Diagnosing why the old head failed

Before fitting a new head, work out why the old one failed. Common causes on UV flatbeds include cured ink in nozzles from reflection or poor capping, physical damage from a crash, electrical damage from hot-plugging or a board fault, and wear after long service. Each cause needs a different fix:

Failure causeEvidenceFix before fitting new head
Cured inkHard deposits on nozzle plateCheck lamp shields, capping, idle settings
Crash damageScratches, dentsFix height setting habits and sensors
Electrical damageOvercurrent errors, burn marksTest board channel and cable
WearGradual nozzle loss after long useNormal replacement
Ink incompatibilitySwelling, leaksCheck ink is suitable for i3200-U1

Head alignment after the change

A new i3200-U1 head must be aligned with the others to avoid banding and misregistration between colour, white and varnish. Typical steps:

  1. Check head height with calipers or the machine’s reference so the nozzle plate sits level with the other heads.
  2. Print the head angle test and adjust the head’s rotation screw until lines are straight.
  3. Print vertical alignment tests and adjust in software or mechanically.
  4. Run bidirectional calibration for each print mode.
  5. Run step or feed calibration as required by your machine.
  6. Print a test image with fine text, gradients, white and varnish.

Capping and idle care for new heads

New heads last longer with good capping. At the end of each shift, park the carriage on the capping station and make sure caps seal properly. Clean capping station sponges and wiper blades regularly. For short idle periods, use the software’s automatic flash or spit settings to keep nozzles wet. UV ink should never be left exposed to light on the nozzle plate. See our UV printer maintenance schedule and head care guide.

XP600 vs i3200-U1 head change differences

AspectXP600i3200-U1
Indian price (2026)About โ‚น12,000โ€“15,000About โ‚น78,000โ€“95,000
CablesRibbon cables, fine pitchRibbon cables, fine pitch, more conductors
BoardXP600-specific boardi3200-specific board; not interchangeable
Voltage settingSet per headSet per head from label
Risk of costly mistakesModerateHigh

The basic steps are similar, but the i3200’s higher price makes every precaution more important.

Warranty and documentation

Most head suppliers do not cover heads damaged by electrical faults, crashes or incorrect handling. Keep evidence that the head was installed properly: photos of the head label and serial, photos of correct cable insertion, the voltage entered, and the first nozzle check print. If the head fails early, this documentation helps support a claim. Buy heads from suppliers who provide test prints before shipping.

When to ask for professional help

If you have never changed an i3200 head, if the old head failed electrically, or if the machine has a history of burnt boards, ask a technician for the first change. Watch and learn the steps. Many owners handle later changes themselves once they have seen it done correctly.

UV flatbed i3200 head change: common mistakes and their cost

MistakePossible damageTypical cost impact
Hot-plugging a cableHead and board channel burntNew head (about โ‚น78,000โ€“95,000) plus board
Cable one pin offOvercurrent, possible burnHead and/or board
Fitting head to untested channelNew head destroyedNew head
Ink spilled on connectorsShort, corrosionCable, adapter, board
Guessing voltagePoor print, shorter head lifeEarly head replacement
Skipping alignmentBanding, misregistrationWasted substrates
Wrong head variantReduced life with UV inkEarly replacement

Head change on multi-head i3200 machines

On three- and four-head i3200 machines, heads are mounted close together, and access is tight. Remove only the head being changed, and protect the neighbouring heads’ nozzle plates from drips and tools. Label each head’s ink lines and cables before disconnection. After fitting, check that the new head sits at exactly the same height as its neighbours, because even small differences affect gloss and dot size, especially between white and colour heads.

Keeping a head history

Record each head’s serial number, installation date, voltage setting, position, ink type and replacement reason. Over time this history shows average head life on your machine, highlights positions that fail more often (often white), and helps you plan head purchases and budgets. It also supports warranty discussions with suppliers.

Cost planning for head changes

Most busy shops replace i3200 heads every so often depending on usage, ink quality and maintenance. Build head replacement into your pricing by estimating cost per square metre or per job. Shops that treat heads as a running cost rather than a surprise are better able to buy genuine parts and avoid risky cheap alternatives.

Checking the capping station after a head change

A new head is only as healthy as the capping station that protects it overnight. After any head change, inspect the cap for that head: the rubber lip should be clean, soft and level, and the cap should rise fully to seal against the nozzle plate. Replace hardened or torn caps, clean the wiper blade, and check that the cleaning pump draws ink properly. A poor seal lets UV ink dry and cure on the nozzle plate, undoing the benefit of an expensive new i3200-U1 head within days. Many shops replace caps and wipers at the same time as the head.

Bottom line

Most burnt head boards after a UV flatbed i3200 head change are caused by hot-plugging, misaligned cables, shorted heads, ink leaks, wrong voltages or static. Switch off, earth yourself, inspect heads and cables, insert cables carefully, prime with power off, enter the correct voltage and test one head at a time. These habits protect both your heads and your boards.

Further reading: The i3200-U1 is a piezo head; this overview of inkjet printing explains how such heads fire droplets.

Key takeaways

  • Never plug or unplug head cables with power on.
  • Insert ribbon cables straight, fully and with correct orientation.
  • Test the board channel before fitting a new head after an electrical failure.
  • Prime with power off and check for leaks.
  • Enter the voltage from the head label and control static.

More in the UV flatbed carriage board series

Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.

Running a UV roll to roll machine as well? The matching guide in our roll to roll series is Burnt Head Board After a Ricoh Head Change.

Frequently Asked Questions

Why do head boards burn after an i3200 head change?

Hot-plugging, misaligned cables, shorted heads, ink on connectors, wrong voltage and static are the main causes.

How much does an i3200-U1 head cost in India?

Indian listings in 2026 ranged from about โ‚น78,000 to โ‚น95,000.

Which i3200 variant should I use on a UV flatbed?

The i3200-U1 is the UV-ink variant. A1 and E1 variants are for water-based and eco-solvent inks.

Can I reseat a head cable with the power on?

No. Always switch off and isolate power first.

Where do I find the head voltage?

On the head label. Enter it exactly for that channel.

What should I do if I see an overcurrent error?

Switch off immediately and check cable seating and the head.

Should I replace the cable with the head?

Replace any cable connected to a failed head or showing damage.

How do I prevent ink leaks during priming?

Prime with power off, check damper connections and wipe any spills before powering up.

Can static damage a new head?

Yes. Use an anti-static strap and keep heads in their packaging until fitting.

Are refurbished i3200 heads safe?

Some are, but others have faults. Buy from trusted suppliers with test prints and warranty.

Why is my new head not detected?

Check cable orientation, seating, locks, damage and firmware.

Should I test the board after a head failure?

Yes. A damaged channel can destroy a new head.

How long does a head change take?

Usually one to two hours including priming and alignment.

Can Unified Engineering Dynamics supply i3200-U1 heads?

Yes. Our team supplies i3200-U1 heads, cables and boards and can advise on safe fitting.

What tools do I need to change an i3200 head?

An anti-static strap, correct screwdrivers, gloves, lint-free cloths, compatible cleaning fluid, syringe, torch, magnifier and labels.

How do I align a new i3200 head?

Check height, adjust head angle, run vertical and bidirectional alignment and calibration, then print a test image.

Is an XP600 board compatible with an i3200 head?

No. i3200 heads need i3200-specific boards.

How do I protect neighbouring heads during a change?

Remove only the head being changed, label lines and cables, and cover neighbouring nozzle plates from drips.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *