UV Printing

UV Flatbed Carriage Board Replacement Checklist: Before, During and After Fitting a New Board

UV Flatbed Carriage Board Replacement: 19-Step Checklist

Direct answer: A safe UV flatbed carriage board replacement follows three stages. Before: confirm the fault with swap tests, find and fix the root cause, identify the board’s system, model and version, record all settings and photograph every connection. During: isolate power, use anti-static precautions, protect the heads from UV ink drips, replace damaged cables and adapters, and fit the new board with every connector fully seated. After: power up without heads where advised, check voltages and temperatures, connect heads one at a time, restore head voltages and settings, recalibrate, and test height sensors and anti-collision before printing on a real job. Skipping steps is how new boards and expensive heads get burnt.

A careful UV flatbed carriage board replacement protects both the new board and your expensive heads.

UV Flatbed Carriage Board Replacement: 19-Step Checklist
UV Flatbed Carriage Board Replacement: 19-Step Checklist

Fitting a new carriage board is not difficult, but mistakes are costly. A Hoson i3200 carriage board costs hundreds of dollars and each i3200-U1 head about โ‚น78,000โ€“95,000 in India. This checklist follows our guide to head cable vs carriage board faults.

Stage 1: before buying

  1. Confirm the fault. Use cable and channel swap tests with power off. Make sure the fault follows the board channel.
  2. Find the root cause. Look for shorted heads, leaking dampers, crash damage, static, overheating or power problems. A new board will fail the same way if the cause remains.
  3. Identify the board. Photograph both sides, note brand, model, part number, version stickers, head connector count and head type.
  4. Record the main board. Note model, version and software version; carriage boards must match.
  5. Check the heads. Have any head connected to the burnt channel tested before reuse.
  6. Confirm compatibility in writing. Send photos to the supplier and get confirmation.

Stage 2: preparation

  1. Back up print control software settings: head voltages, temperatures, offsets, calibration, flatbed height settings.
  2. Photograph every connector and cable route on the carriage.
  3. Label cables with masking tape.
  4. Gather tools: anti-static strap, screwdrivers, lint-free cloths, gloves, torch, magnifier.
  5. Have new cables and adapters ready if the old ones were involved in a short.
  6. Park the carriage in a safe position with heads capped or protected.

Stage 3: removal

  1. Switch off and disconnect mains power. Switch off lamps and chiller.
  2. Wait for capacitors to discharge as advised by the supplier.
  3. Wear an anti-static strap connected to machine earth.
  4. Remove the carriage cover carefully, avoiding ink drips onto boards.
  5. Release locking tabs and remove cables straight out.
  6. Remove board screws and standoffs; keep them safe.
  7. Inspect the area under the board for ink, burns and debris; clean it.

Stage 4: fitting the new board

  1. Check the new board for shipping damage and matching part numbers.
  2. Mount it with all original standoffs and screws; avoid stress on the board.
  3. Connect power, data and sensor cables first, following photos.
  4. Do not connect head cables yet if the supplier advises a first power-up without heads.
  5. Check every connector is straight, fully seated and locked.
  6. Route cables away from lamp housings and moving parts.

Stage 5: first power-up

  1. Power up and watch for smoke, smells or abnormal heat; switch off immediately if seen.
  2. Check the software recognises the board and firmware.
  3. Update firmware only if the supplier specifies it.
  4. Check supply voltages where test points are provided, or ask a technician.
  5. Switch off before connecting heads.

Stage 6: connecting heads

  1. Connect one head at a time with power off.
  2. Power up and check detection and temperature.
  3. Enter the head’s voltage from its label; never guess or copy another head’s value.
  4. Print a nozzle check for that head.
  5. Repeat for each head.

Head voltage settings for i3200-U1 heads are covered in our guide to Epson i3200-U1 head voltage on UV flatbeds.

Stage 7: calibration and flatbed checks

  1. Restore temperatures and other settings from the backup.
  2. Run head alignment, bidirectional and step calibration.
  3. Test the height sensor and anti-collision switch.
  4. Check lamps switch on and off correctly.
  5. Check vacuum and table or gantry motion.
  6. Print white, colour and varnish test files on a scrap sheet.

Stage 8: after the job

  1. Record the board model, version, date and supplier in the maintenance log.
  2. Keep the old board labelled; it may be repairable as a spare.
  3. Keep invoices and photos for warranty.
  4. Monitor the machine closely for the first week.

Common mistakes

MistakeConsequence
Not fixing the root causeNew board burns in the same way
Wrong versionBoard not recognised, downtime
Reusing damaged cablesRepeated shorts
Hot-plugging headsBurnt heads and channels
Guessing head voltagePoor print or shortened head life
Skipping sensor testsCrash risk
No backup of settingsHours of recalibration

When to call a technician

Call a technician if the board system or firmware is unfamiliar, if the fault cause is unclear, if heads may be shorted, or if the machine is under warranty. Many suppliers provide remote support for firmware and settings.

Example: smooth replacement

A Ghaziabad sign shop replaced a burnt Hoson i3200 carriage board after a damper leak. It replaced the damper and cable, confirmed the board version with the supplier, backed up settings and connected heads one at a time. The machine was printing again within three hours.

Example: costly shortcut

Another unit fitted a new carriage board without testing the head that had been connected to the burnt channel. The head was shorted and burnt the new board within minutes. Testing the head first would have saved a board.

Printable UV flatbed carriage board replacement checklist

Print this table and tick each item as you go. It condenses the stages above into a single page that can be kept with the machine.

#ItemDone
1Fault confirmed with cable and channel swap testsโ˜
2Root cause identified and fixed (leak, short, crash, heat, power, static)โ˜
3Old board photographed both sides, labels readableโ˜
4Main board model and software version recordedโ˜
5Compatibility confirmed in writing by supplierโ˜
6Heads from failed channel testedโ˜
7Settings backed up (voltages, temperatures, offsets, height)โ˜
8Connections photographed and labelledโ˜
9Power isolated, lamps and chiller offโ˜
10Anti-static strap worn and earthedโ˜
11Damaged cables and adapters replacedโ˜
12New board mounted with all standoffsโ˜
13First power-up checked without heads (if advised)โ˜
14Heads connected one at a time, voltages from labelsโ˜
15Nozzle checks, alignment and calibration completeโ˜
16Height sensor and anti-collision testedโ˜
17Lamps, vacuum and motion checkedโ˜
18Test print on scrap sheet approvedโ˜
19Maintenance log and invoice filedโ˜

Backing up print control settings

Most Hoson, Senyang and BYHX software allows settings to be exported or saved as configuration files. Before any board work, save these files to a USB drive and to cloud storage. If export is not available, photograph every settings screen: head voltages, temperatures, head offsets, bidirectional values, step calibration, white and varnish layer settings, height and Z-axis parameters, and lamp settings. Label each photo with the date. Restoring from these records can save hours of recalibration and avoids guessing voltages, which is risky for expensive heads.

Firmware and version matching

New boards sometimes arrive with firmware that differs from your main board. In some systems the software will warn you; in others the board simply fails to connect. Never flash firmware unless the supplier has confirmed the exact file for your board pair, because a wrong file can make a board unusable. Keep a record of firmware versions for both boards after installation. See our guide to UV flatbed firmware updates for safe practice.

Testing heads before reconnection

A head that was connected to a burnt channel may be damaged even if it looks fine. Technicians can measure resistance across key pins and compare with a known good head of the same type, or test it on a dedicated test board. Some suppliers offer head testing services. Only reconnect a head to a new board when it has passed these checks. This single step prevents the most common and expensive repeat failure.

Downtime planning

Board failures rarely happen at convenient times. Reduce downtime by keeping essential spares, knowing your board version in advance, having a supplier contact who can confirm compatibility quickly, and keeping settings backups up to date. If a replacement must be imported, ask customers about deadlines early and consider outsourcing urgent jobs to a partner shop. For a shop earning steady daily income from its flatbed, a spare board can pay for itself after just a few days of avoided downtime.

Post-installation monitoring

DayCheck
Day 1Nozzle checks morning and afternoon, temperature readings, any errors
Days 2โ€“3Board area temperature after long jobs, cable seating
Week 1Alignment recheck, sensor test, log review
Month 1Inspect board for ink, heat marks, loose connectors

Early problems are usually covered by warranty, so report anything unusual to the supplier quickly with photos and logs.

Who should do the work

Experienced operators can replace boards if they follow the checklist carefully and the supplier supports them. If the machine is under warranty, if the fault cause is unclear, or if firmware changes are involved, use a trained technician. The cost of a technician visit is small compared with the cost of a burnt head or a second board.

UV flatbed carriage board replacement on Epson vs Ricoh machines

AspectEpson-head flatbed (XP600, i3200-U1)Ricoh-head flatbed (Gen5, Gen6)
Board locationUnder carriage cover, usually one boardLarger carriage, sometimes several boards
Head connectionFine-pitch ribbon cablesAdapter boards and dedicated cables
Main data linkFlat cable or networkCable bundle or fibre
Typical replacement time2โ€“3 hours3โ€“6 hours including calibration
Key riskAngled ribbon insertionOvercurrent from damaged heads or adapters

On Ricoh machines, the carriage may carry separate boards for head groups or for heating. Check which board actually failed before ordering, and confirm whether head waveform or settings files need reloading after replacement.

Cleaning the carriage during replacement

A board replacement is the best opportunity to clean the carriage thoroughly. With the board removed and power off, clean the mounting area, remove cured ink with approved tools, check dampers and ink lines for leaks, inspect heater wiring and sensor plugs, and clean fan blades. Many shops discover the original cause of failure during this cleaning, such as a cracked damper dripping onto the board area or a fan clogged with ink dust. Fixing these issues now protects the new board.

Common post-replacement problems

ProblemLikely causeFix
Board not recognisedVersion or firmware mismatch, data cableCheck version, cable, supplier advice
One head not detectedCable orientation or seatingPower off, reseat
Colours swappedCables in wrong connectorsCompare with photos and labels
Temperature errorsHeater plug not connectedPower off, reconnect
Collision alarm stuckSensor plug missingReconnect sensor
BandingCalibration not redoneRun alignment and calibration

Spare parts to have ready before a UV flatbed carriage board replacement

Gather everything before you open the carriage, so the machine is not left half-dismantled while you wait for a small part. A sensible kit includes the new board, matching head data cables for every channel that was involved, spare adapter boards, a main data cable or fibre link, replacement dampers if leaks were found, a fresh set of capping station sponges and wipers, cable ties and labels, and a printed copy of your settings backup. If the failure was caused by heat, also have a replacement carriage fan ready. If the failure was caused by power problems, arrange for an electrician to check the earth and stabiliser on the same day. Having these parts ready often turns a two-day repair into a single afternoon.

Bottom line

A careful UV flatbed carriage board replacement protects both the new board and your heads. Confirm the fault, fix the root cause, match the board exactly, back up settings, replace damaged cables, connect heads one at a time with correct voltages, and test sensors and calibration before printing real jobs.

Further reading: Handling rules above guard against electrostatic discharge, which can damage boards without visible marks.

Key takeaways

  • Confirm the fault and fix the root cause before buying.
  • Match system, model and version exactly.
  • Back up settings and photograph connections.
  • Power off for every connection and connect heads one at a time.
  • Recalibrate and test height and collision sensors.

More in the UV flatbed carriage board series

Related reading on our site: UV flatbed printer spare parts buyer’s guide, UV flatbed boards, cables, motors and interlock spares, UV flatbed printer problems and fixes, Epson i3200 vs XP600 printheads and UV flatbed printer price in India.

Running a UV roll to roll machine as well? The matching guide in our roll to roll series is UV Carriage Board Replacement Checklist.

Frequently Asked Questions

What should I do before replacing a UV flatbed carriage board?

Confirm the fault, fix the root cause, identify the board and version, back up settings and photograph connections.

Why must I fix the root cause first?

A shorted head, ink leak or power problem will damage the new board in the same way.

Can I connect all heads at once?

It is safer to connect one at a time with power off and check each.

Where do I find the head voltage?

On the head’s label or documentation. Never guess or copy another head’s value.

Should I replace cables with the board?

Yes, if they were involved in a short or crash.

Do I need to update firmware?

Only if the supplier specifies it for compatibility.

What should I check after fitting?

Detection, temperatures, voltages, nozzle checks, alignment, height sensor, collision switch, lamps and vacuum.

Should I keep the old board?

Yes. It may be repairable as a spare and may be needed for warranty.

Can static damage the new board?

Yes. Use an anti-static strap and handle boards by the edges.

How long does a replacement take?

Typically a few hours including calibration, if parts and settings are ready.

What if the new board is not recognised?

Check version, firmware, cables and software, and contact the supplier.

Should I test heads from the burnt channel?

Yes. A shorted head can burn the new board.

When should I call a technician?

When the system or cause is unclear, heads may be shorted or the machine is under warranty.

Can Unified Engineering Dynamics help with board replacement?

Yes. Our team can help identify boards, supply parts and advise on replacement steps.

How do I back up flatbed print settings?

Export configuration files if the software allows it, or photograph every settings screen with dates.

Should I flash firmware myself?

Only with the exact file confirmed by the supplier for your board pair. A wrong file can make the board unusable.

What should I monitor after fitting a new board?

Nozzle checks, temperatures, errors, board area heat, alignment and sensor tests over the first week and month.

Why are colours swapped after replacing the board?

Head cables were connected to the wrong board connectors. Compare with your photos and labels.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *