UV Printing

UV Printer Fault Finding: Is It the Board, Head, Cable or Lamp? A Step-by-Step Guide

UV Printer Fault Finding: Board, Head, Cable or Lamp?

Direct answer: Good UV printer fault finding starts by defining the symptom and what it affects: one nozzle area, one head, one colour, all heads, motion, curing or communication. Then check the simple causes first, such as ink supply, head temperature, settings, cables and power, before suspecting boards. Swap heads or cables between channels with power off to see whether a fault follows the head, the cable or the board channel. Check curing separately from printing, because lamp and chiller faults cause tacky prints rather than missing nozzles. Record every step, fix the root cause, and test driver channels before fitting new heads.

Structured UV printer fault finding saves parts and protects new heads, because guessing usually replaces the wrong component first.

UV Printer Fault Finding: Board, Head, Cable or Lamp?
UV Printer Fault Finding: Board, Head, Cable or Lamp?

On a UV roll to roll printer, a single symptom can have many causes. Missing colour might be a clogged nozzle, air in a damper, a cold head, a bad cable, a failed driver channel or a carriage board fault. Guessing leads to wasted parts and sometimes destroyed heads. This guide gives a structured fault-finding method. It draws on our complete guide to UV roll to roll printer electronics.

UV printer fault finding step 1: define the symptom precisely

Write down exactly what you see. Useful questions:

  • What is affected: a few nozzles, a whole head, one colour, all heads, motion, curing, communication?
  • When did it start, and what changed just before?
  • Is it constant or intermittent?
  • Does it change with temperature, time, media or print mode?
  • Are there error messages? Take screenshots.

Step 2: map the symptom to likely areas

SymptomLikely areas, in order
Scattered missing nozzlesInk, air, dust, cured ink on plate, cleaning
One head faint or blankInk supply, temperature, settings, cable, driver channel, head
One colour of two-colour head missingInk supply for that colour, damper, head row, driver path
All heads stop, motion OKData link, carriage board, main board
Carriage will not moveSensors, encoder, servo driver, main board, power
Prints tacky or poorly curedLamps, chiller, lamp settings, ink, speed
BandingFeed calibration, nozzles, encoder, head alignment
Printer not detectedCable, PC settings, network, main board port
Random resetsPower, heat, PC, loose connections

Step 3: check the simple causes first

  • Ink: levels, dampers, filters, pressure, white ink circulation.
  • Temperature: heads at set point, room temperature, chiller readings.
  • Settings: voltages, waveforms, print mode, lamp power, compared with records.
  • Cleaning: nozzle plate condition, wiper and capping station.
  • Cables: seated, undamaged, no ink on connectors.
  • Power: stable supply, earthing, power supply outputs.

Most faults are found at this stage.

Step 4: use swap tests

Swap tests show whether a fault follows the head, cable or board channel. Always switch off and unplug first, and use anti-static precautions.

SwapIf the fault movesIf the fault stays
Swap head cables between two channels at the boardBoard channel is OK; fault is head or cableBoard channel suspected
Swap heads’ cables at the head endFault follows headFault in cable or channel
Replace cable with a spareCable was faulty if fault clearsHead or channel

Be careful: if a head may be shorted, do not move it to a healthy channel without testing, or you may damage that channel too. Our article on cable vs carriage board faults explains safe swaps.

Step 5: separate curing faults from printing faults

Curing faults show as tacky, smudging or poorly adhering prints, not missing nozzles. Check:

  • Both lamps on and at the set power.
  • Chiller flow and temperature.
  • Lamp windows clean.
  • Lamp height and shields correct.
  • Print speed and passes suitable for the ink.
  • Ink suitable for lamp wavelength.

See our guides to UV curing problems and cure and adhesion testing.

Step 6: inspect and measure

With power off, inspect boards for burns, swollen capacitors, ink and corrosion, and connectors for burnt pins. A technician can then measure power supply outputs, driver outputs and signals. Do not attempt live measurements without training.

Step 7: fix the root cause

Replacing a part without fixing why it failed invites repeat failures. Common root causes: heat, ink leaks, static, cable wear, power problems, handling errors and wrong settings.

Step 8: protect new parts

  • Test driver channels before fitting new heads after a head failure.
  • Replace suspect cables and adapters with heads.
  • Enter correct settings before first firing.
  • Power up carefully and monitor.

See why bad driver boards damage new heads.

Fault-finding examples

Example 1: cyan fading every afternoon

Symptom: cyan head faint after lunch. Simple checks: ink and filters fine, head temperature normal. Room temperature high; carriage fan slow. Fix: clean and replace fan; driver stopped overheating.

Example 2: all heads stop mid-job

Symptom: carriage moves, no ink. Check data link: internal cable cracked in cable chain. Fix: replace cable and re-route.

Example 3: tacky prints on one side

Symptom: poor curing on the left. Left lamp running hot. Chiller hose kinked. Fix: re-route hose.

Example 4: new head fails immediately

Symptom: overcurrent on new head. Previous head failed on same channel. Driver channel tested and found faulty. Fix: repair driver, replace cable, fit tested head.

Tools for fault finding

ToolUse
Nozzle check prints and photosTrack head condition over time
Fault diaryReveal patterns
Infrared thermometerCompare heat sink and lamp temperatures
MultimeterMeasure power supplies (trained staff)
Spare cablesQuick swap tests
Anti-static wrist strapSafe handling
Torch and magnifierInspect boards and connectors

Fault finding by subsystem

Ink and head subsystem

Most print defects start here. Check ink levels, pressure or negative pressure, dampers, filters and, for white ink, circulation. Inspect the nozzle plate for cured ink or damage and check the capping station and wiper. A head that recovers after cleaning has an ink or maintenance problem, not an electronic one. A head that stays blank after good cleaning and correct ink supply moves suspicion to temperature, settings, cable, driver or the head itself.

Temperature subsystem

UV ink is viscous and depends on correct head temperature. Check that each head reaches its set point and that the heater and thermistor readings are stable. A head that never reaches temperature may have a heater fault, a connection problem or a carriage board heater channel fault. Check room temperature too: very cold rooms in winter mornings can slow warm-up, while very hot rooms in summer can overheat boards.

Data subsystem

Data problems usually affect whole heads, groups of heads or all heads together. Typical causes include internal cables worn in the cable chain, loose connectors, fibre links bent too tightly, and electrical noise. A fault that affects all heads at once points to the link between main board and carriage, or to the carriage board itself.

Motion subsystem

Motion faults include the carriage not moving, crashing, losing position or uneven feed. Check limit and origin sensors, the encoder strip and reader, belts, servo drivers and media feed. Dirt on the encoder strip causes many position and banding problems.

Curing subsystem

Curing faults affect print durability rather than image. Check lamps, lamp power supplies, chiller, windows and settings, as described above.

Power subsystem

Power faults cause resets, random errors and failures across several subsystems. Check the incoming supply, stabiliser, UPS, internal power supplies and earth. If faults correlate with other machines starting, generator changeovers or storms, power is likely involved.

Communication subsystem

If the PC cannot see the printer, check cables, ports, PC settings, network settings, software versions and licence. See our guide to UV printer connection problems.

Reading error messages

Error messages are clues, not verdicts. An “overcurrent” message points to a head or driver channel but can also be caused by a shorted cable. A “head not detected” message can come from a loose connector as easily as a failed board. A “communication error” may be a USB power-saving setting. Note the exact wording and code, search the software manual, and check with your supplier. Record the error alongside the conditions in your fault diary.

Intermittent faults

Intermittent faults are the hardest. They often relate to heat, vibration, power or noise. Strategies:

  • Log every occurrence with time, temperature, job and what else was running.
  • Gently move cables while printing a test to find loose connections (only if safe and with care).
  • Monitor temperatures through the day.
  • Check whether faults coincide with other machines, generators or weather.
  • Run long test jobs to reproduce the fault.

Patterns usually emerge within a week or two of careful logging.

Common fault-finding mistakes

MistakeConsequenceBetter approach
Replacing the most expensive part firstWasted money, fault remainsCheck simple causes first
Swapping parts with power onBurnt boards and headsAlways switch off
Fitting a new head without testing the channelNew head destroyedTest driver channel first
Changing several things at onceCannot tell what fixed itOne change at a time
Not recording findingsSame fault returns, same investigationKeep a fault diary
Ignoring root causeRepeat failureFix heat, ink, power or handling issues

Fault finding flow for “one head blank”

  1. Clean the head and print a nozzle check. If it recovers, investigate ink supply and maintenance.
  2. Check the ink supply to that head: tank, filter, damper, pressure.
  3. Check head temperature reaches set point.
  4. Check settings for that head against records.
  5. With power off, inspect the cable and connectors at both ends.
  6. Swap the cable with a known good spare.
  7. Swap channels at the board (only if the head is not suspected of a short).
  8. If the fault follows the channel, call a technician to test the driver and carriage board.
  9. If the fault follows the head, test the head’s resistance or have it assessed.
  10. Fix the root cause before fitting new parts.

Fault finding flow for “printer not printing at all”

  1. Check the PC sees the printer and the software shows it connected.
  2. Check for error messages.
  3. Check power to the printer and that boards show normal status LEDs.
  4. Check cables between PC and printer.
  5. Check the job in the RIP and print queue.
  6. Check the data link between main board and carriage.
  7. Check carriage board power and status.
  8. Consult a technician for board-level checks.

Fault finding flow for “poor curing”

  1. Check both lamps switch on during printing.
  2. Check lamp power setting.
  3. Check chiller temperature and flow.
  4. Clean lamp windows.
  5. Check lamp height and shields.
  6. Reduce speed or increase passes to test.
  7. Confirm ink suits the lamp wavelength.
  8. Test with a known good ink and media.
  9. If output is low, have the lamp tested or replaced.

When to stop and call for help

Stop and call a technician when there is a burning smell or visible burn marks, overcurrent errors repeat, faults point to a board after simple checks, a second head fails on the same channel, or you are unsure about safe measurements. Continuing to experiment can turn a small repair into an expensive one. When you call, share your fault diary and swap test results; this often lets a technician diagnose remotely.

Learning from every fault

After each fault, ask what caused it and what would have prevented it. Update your maintenance checklist, training or spares accordingly. Over months, this habit sharply reduces failures. Our preventive maintenance checklist and spares inventory guide help put lessons into practice.

Fault finding for multi-machine shops

Shops with several UV roll to roll printers have an advantage: comparison. If two machines share the same board system and heads, a suspect cable, board or lamp can be tested on the healthy machine, with care and power off, to confirm whether it is faulty. Be cautious with suspected shorted heads or burnt boards, which can damage the healthy machine. Comparing temperatures, settings and logs between machines also reveals problems. If one machine runs hotter or needs more cleaning, investigate why. Standardising board systems and heads across machines makes this approach far more powerful.

Documenting a fault for remote support

Good documentation lets a technician help without visiting. Include the machine profile, a clear description of the symptom, photos or videos of the fault and error messages, nozzle check images, settings screenshots, the steps already tried and their results, and recent changes. Many faults can be diagnosed in a phone or video call with this information, saving time and travel costs.

Bottom line

UV printer fault finding is a method, not a guess. Define the symptom, check simple causes first, use safe swap tests, separate curing from printing faults, call for help at the right time and fix the root cause. This approach saves parts, protects new heads and gets your printer back into production faster.

Further reading: The method follows classic troubleshooting: isolate, test one change at a time and confirm the fix.

Key takeaways

  • UV printer fault finding starts with a precise symptom and what it affects.
  • Check ink, temperature, settings, cleaning, cables and power before boards.
  • Swap tests show whether faults follow heads, cables or channels.
  • Separate curing faults from printing faults.
  • Fix root causes and protect new parts.

More in the UV roll to roll electronics guides

Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.

Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine main board and the complete eco-solvent printer electronics guide.

Frequently Asked Questions

How do I know whether a fault is the head or the board?

Swap cables between channels with power off. If the fault follows the head, the head is likely at fault; if it stays with the channel, suspect the board or cable.

Why are my prints tacky?

Usually curing problems: lamp power, chiller cooling, dirty lamp windows, speed or ink. Check lamps and chiller first.

All heads stopped but the carriage moves. What should I check?

The data link between the main board and carriage, then the carriage board and main board.

Is it safe to swap heads between channels?

Only with power off, and avoid moving a possibly shorted head to a healthy channel without testing.

What are the most common causes of missing nozzles?

Ink supply problems, air, dust, cured ink on the nozzle plate and cleaning issues.

Should I raise voltage if a head is weak?

Not before checking ink, temperature and maintenance. Raising voltage to hide faults stresses heads and drivers.

What tools do I need for fault finding?

Nozzle check records, a fault diary, an infrared thermometer, spare cables, an anti-static strap and, for trained staff, a multimeter.

Why keep a fault diary?

It reveals patterns related to time, temperature, media or other machines that point to root causes.

When should I call a technician?

When swap tests point to a board, when there is visible damage, when overcurrent errors repeat, or before fitting new heads after a failure.

Can banding be an electronics fault?

Occasionally, but feed calibration, nozzle problems, encoder dirt and alignment are more common causes.

What should I do after fixing a fault?

Fix the root cause, record what happened and update your maintenance routine.

Can Unified Engineering Dynamics help with fault finding?

Yes. Our team can help diagnose faults and supply parts for UV roll to roll printers.

How do I find intermittent faults?

Log every occurrence with conditions, monitor temperatures, check correlations with other machines or weather, and run long tests to reproduce the fault.

Does an overcurrent error always mean a bad head?

No. It can also be a driver channel fault or a shorted cable. Investigate before replacing parts.

When should I stop fault finding and call a technician?

When you see burns, overcurrent errors repeat, faults point to a board, a second head fails on the same channel, or you are unsure about safe measurements.

Can I use a second machine to test parts?

Yes, with power off and care, if both use the same system. Avoid moving suspected shorted heads or burnt boards to a healthy machine.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *