UV Printing

UV Printer Compatibility Table: Heads, Boards, Lamps, Inks and RIP for Roll to Roll Machines

UV Printer Compatibility Table: Heads, Boards, Lamps, RIP

Direct answer: A UV printer compatibility table links each printhead family to the board systems, ink types, lamp wavelengths and RIP or control software it works with. In short: Ricoh Gen5 and Gen5i heads need Gen5-compatible boards (commonly BYHX or Hoson Ricoh kits); Ricoh Gen6 needs Gen6-specific boards and software; Konica KM1024i and KM512i need Konica-specific boards, commonly BYHX; Kyocera heads usually need the machine maker’s electronics; and Epson i3200-U1 heads need Epson-specific boards such as Hoson or Senyang. UV ink must be approved for the head and matched to the lamp wavelength, typically 395 nm LED. Board systems never mix, and versions, head counts and firmware must match too.

Use this UV printer compatibility table before buying any head, board, lamp, ink or RIP upgrade, because mismatches are expensive.

UV Printer Compatibility Table: Heads, Boards, Lamps, RIP
UV Printer Compatibility Table: Heads, Boards, Lamps, RIP

Compatibility errors are among the most expensive mistakes in UV printing: a wrong board that will not communicate, an ink that damages heads, or a lamp that will not cure the ink. This guide brings compatibility rules from our UV roll to roll printer electronics series into reference tables. Use them as a starting point and always confirm with your supplier.

UV printer compatibility table: head to board system

PrintheadCommon board systemsNotes
Ricoh Gen5BYHX, Hoson Ricoh kits, othersGen5 boards; check head count and version
Ricoh Gen5iGen5-compatible boards in many casesConfirm settings and support with supplier
Ricoh Gen6Gen6-specific BYHX, Hoson and other kitsGen5 boards generally not compatible
Konica KM1024iBYHX and similar industrial systemsMatch drop-size variant
Konica KM512iBYHX, UMC and othersCommon on solvent; some UV machines
KyoceraMachine maker’s electronics, specialised systemsUsually not sold separately
Epson i3200-U1Hoson, SenyangUse UV variant only with UV ink

See our guide to UV driver board compatibility.

Board to board

RuleWhy
Main board, carriage board and driver/adapter boards must be from the same systemDifferent firmware, protocols and connectors
Versions must be compatibleFirmware mismatches cause recognition errors
Head count must matchA 4-head board cannot run 8 heads
Cables must match board revisionPinouts can differ
Power supplies must suit board requirementsWrong voltages damage boards

Board system to software and RIP

ItemCompatibility rule
Print control softwareSupplied with the board system; version must match firmware
Software licenceMay be tied to main board or dongle
RIP (e.g. PhotoPrint, Maintop, Onyx, Caldera)Must support the board system and printer model; check version
Colour profilesSpecific to ink, media, print mode and head; rebuild after major changes

Head to ink

RuleDetail
Use UV ink approved for the headAsk ink maker for head approval and settings
Match head temperature to ink data sheetUV ink viscosity depends on temperature
Use correct waveformWaveforms are ink- and head-specific
Flush properly when changing inkMixing incompatible inks can gel in heads
Epson heads: UV variant onlyEco-solvent variants are not intended for UV ink

See our guide to UV printhead and ink compatibility.

Ink to lamp

LampInk requirement
395 nm LED (most common)LED-curable UV ink formulated for around 395 nm
365 nm or other LEDInk formulated for that wavelength
Mercury arc (older machines)Ink formulated for broad-spectrum curing

Ink that is not matched to the lamp may stay tacky. See how UV ink curing works.

Lamp to machine

CheckDetail
Dimensions and mountingMust fit carriage brackets
Power and connectorMust match lamp power supply
Cooling typeWater-cooled lamps need chiller; air-cooled need fans
Control signalsOn/off and power level compatible with main board
Chiller capacityMust handle lamp heat

See UV LED lamp replacement checks.

Media compatibility

UV roll to roll printers print on PVC, PET backlit film, vinyl, wallpaper, canvas, textiles and flex. Each media needs suitable ink adhesion, curing settings and sometimes primer. Static-prone films need good earthing. Test new media with adhesion tests before production.

Master compatibility checklist

  1. Head type and variant identified from labels.
  2. Board system, versions and head count recorded.
  3. Software version and licence confirmed.
  4. RIP supports printer and board system.
  5. Ink approved for head, with settings.
  6. Ink matched to lamp wavelength.
  7. Lamp fits machine and chiller capacity.
  8. Cables match board revision.
  9. Power supplies suit boards and lamps.
  10. Written confirmation from supplier for any new part.

Example: ink and lamp mismatch

A unit bought cheaper UV ink without checking wavelength. Prints stayed tacky despite full lamp power. The ink was formulated for a different curing system. Switching to an LED-curable ink matched to 395 nm solved the problem.

Example: board version mismatch

Another unit bought a carriage board from the correct system but a newer version. The main board did not recognise it until firmware was updated. The supplier provided files and sequence.

Compatibility of cables and connectors

Head data cables look similar across systems but differ in length, pin count, shielding and pinout. Using the wrong cable can damage boards and heads. Always replace cables with the type specified for your board system and head, and check orientation markings. Gen6 heads, for example, generally use different cables and adapters from Gen5 heads. Fibre links, where used, must match the transceivers on both boards.

Compatibility of power supplies

Each board and lamp requires specific voltages and current capacity. A replacement power supply must match output voltages, current rating, connectors and mounting. A higher-current supply at the correct voltage is usually acceptable; a different voltage is never acceptable. Head voltages are generated by the driver section from these supplies, so an unstable supply affects jetting.

Compatibility across print modes and heads in one machine

Many UV roll to roll machines use separate heads for CMYK, white and varnish. The board system must support the head count and configuration. White ink heads often need circulation and different temperature settings. Varnish heads may need different waveforms. Check that your board and software support the configuration before adding white or varnish. See our guide to white ink circulation.

Firmware and software version compatibility

Within a board system, firmware on the main board, carriage board and sometimes driver boards must be compatible with each other and with the print control software. When replacing one board, the supplier may need to update firmware on others. Record all versions and follow the supplier’s update sequence. See our firmware update guide.

Head variants and settings

Head familyVariant differencesCompatibility impact
Ricoh Gen5 vs Gen5iGen5i is a later variantOften similar boards; confirm settings
Ricoh Gen5 vs Gen6Different generationNew boards, cables, software, waveforms
Konica KM1024i variantsDifferent drop sizesDifferent waveforms and settings
Epson i3200 variantsUV, eco-solvent, water-based versionsUse UV version only for UV ink

See our comparison of Ricoh Gen5 vs Gen5i and Konica vs Ricoh vs Epson.

Upgrade compatibility

UpgradeWhat usually changes
Gen5 to Gen6 headsCarriage/driver boards, cables, adapters, software, waveforms, profiles
Adding white or varnish headsHead count support, ink system, software, maybe boards
Changing ink brandWaveforms, temperatures, profiles, flushing
Changing lamp modelMounting, power supply, chiller, control signals, curing settings
Changing RIPPrinter driver support, profiles, workflows
Changing board systemAlmost all electronics and software

See our Gen5 to Gen6 upgrade guide.

Recording your machine’s compatibility profile

Create a one-page profile for each machine listing: printer model and width, board system and versions, firmware versions, software and licence, RIP and version, head types, serials and positions, head settings, ink brand and type, lamp model and wavelength, chiller model, power supply types and cable types. Update it after every change. With this profile, checking compatibility of any new part takes minutes.

Compatibility questions to ask suppliers

  • Is this part compatible with my board system, version and head count?
  • Will firmware on other boards need updating?
  • Does it need different cables or adapters?
  • Will my software licence still work?
  • Are settings or waveforms different?
  • Does my RIP support it?
  • What warranty applies, and what voids it?
  • Can you confirm compatibility in writing?

Compatibility of chillers and coolant

Chillers must suit the lamp’s heat output, flow requirements and fittings. CW-5200 class chillers are common on UV roll to roll printers with LED lamps; larger lamp sets may need bigger units. Coolant must be the type recommended by the lamp and chiller makers; tap water can cause scale, corrosion and algae. Check hose diameters and fittings when replacing a chiller. Indian prices for CW-5200 chillers ranged from about โ‚น24,000 to โ‚น35,000 in late 2026 listings.

Compatibility of power protection

Stabilisers and UPS units must be sized for the load. Lamps and chillers draw significant power; electronics need clean power. Many shops use a servo stabiliser for the whole machine and an online UPS for the PC and electronics only. Surge protective devices must suit the supply type and be installed by an electrician. See our guide to power fluctuation, stabilisers, UPS and earthing.

Compatibility of used and refurbished parts

Used and refurbished parts can be good value but carry extra compatibility risk: older versions, unknown firmware, modified boards and missing accessories. Ask for photos of labels, version details and test evidence. Get return terms in writing. Test the part as soon as it arrives.

Common compatibility mistakes

MistakeResult
Buying by head type onlyBoard from wrong system or version
Ignoring head countBoard cannot drive all heads
Reusing old cables after upgradeRecognition errors or damage
Changing ink without checking approvalHead damage, poor jetting
Changing lamp without checking wavelengthPoor curing
Using wrong power supply voltageBoard damage
Ignoring software licenceMachine will not print

Example: white ink upgrade

A unit wanted to add white ink to a CMYK machine. The board system supported extra heads, but the software licence did not include white, and the ink system needed circulation. After updating the licence, adding circulation and setting white head parameters, the upgrade worked. Checking all compatibility points beforehand avoided buying unsupported parts.

Quick-reference: questions by part type

Buying aโ€ฆConfirm
PrintheadModel, variant, drop size, board support, waveform, ink approval, cables
Carriage or driver boardSystem, version, head type and count, firmware, cables, adapters
Main boardSystem, version, head support, firmware, software, licence, ports
UV LED lampSize, mounting, wavelength, power, connector, cooling, control signal
ChillerCooling capacity, flow, fittings, coolant, power supply
InkHead approval, lamp wavelength, temperature, waveform, media adhesion
RIPPrinter and board support, version, licence, profiles
Power supplyVoltages, current, connectors, mounting
CablesSystem, head type, length, pin count, revision

Compatibility and printing applications

Application needs also affect compatibility choices. Backlit film needs good density and often white ink layers; wallpaper needs flexibility and low odour; soft signage and textiles need suitable ink adhesion; outdoor vinyl needs durability. The combination of head, ink, lamp and RIP settings must suit the application. When moving into a new application, test the complete combination and build profiles before taking orders. Our guide to UV roll to roll vs eco-solvent printers discusses where UV fits best.

Compatibility over the machine’s life

Over years, board versions, firmware, software and ink formulations change. Parts available today may differ from those fitted when your machine was new. Keep your machine profile current, ask suppliers about long-term availability, and consider buying key spares while compatible versions remain available. When a part is discontinued, suppliers often offer an upgrade kit that changes several parts together; plan these upgrades rather than waiting for a failure.

Compatibility and the Indian market

In India, many UV roll to roll printers are imported from China with BYHX, Hoson or Senyang electronics and Ricoh or Konica heads. Local traders stock common boards, heads, cables and lamps for popular configurations. Less common configurations may need imports. When buying a machine, ask which electronics it uses and whether local traders stock spares. Standard configurations make long-term ownership easier and cheaper.

Example: RIP version mismatch

A unit upgraded its RIP to a newer version expecting better colour management. The new version did not yet include a driver for their board system and printer model, so jobs would not send. Reverting to the previous version restored printing while they waited for the RIP maker to release support. Checking the RIP’s supported printer list before upgrading would have avoided a day of lost production. The same applies when changing board systems: confirm RIP support first, then buy.

Keeping a record of which RIP, software and firmware versions work together on each machine is one of the simplest and most valuable compatibility habits. When something changes, you know exactly which combination to return to if problems appear.

Bottom line

A UV printer compatibility table is only as good as the information you feed it. Keep an up-to-date machine profile, check every new part against heads, boards, firmware, software, RIP, ink, lamps, chiller and power, and get written confirmation from suppliers. This avoids the most expensive mistakes in UV printing.

Further reading: Most UV LED lamps emit near 395 nm in the ultraviolet range, and ink must be formulated for it.

Key takeaways

  • A UV printer compatibility table links heads, boards, software, inks, lamps and media.
  • Board systems never mix; versions, head counts and cables must match.
  • Ink must be approved for the head and matched to lamp wavelength.
  • Lamps must fit the machine, power supply, controls and chiller.
  • Always get written confirmation from suppliers.

More in the UV roll to roll electronics guides

Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.

Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine main board and the complete eco-solvent printer electronics guide.

Frequently Asked Questions

Which boards work with Ricoh Gen5 heads?

Gen5-compatible boards from systems such as BYHX and Hoson Ricoh kits. Check version and head count.

Can I use Gen5 boards with Gen6 heads?

Generally no. Gen6 heads need Gen6-compatible boards and software.

Can I mix boards from different systems?

No. Main, carriage and driver boards must be from the same system.

Does my RIP work with any board system?

Not necessarily. Check that your RIP supports your printer model and board system.

What lamp wavelength do most UV roll to roll printers use?

Most use LED lamps around 395 nm. Ink must be formulated for that wavelength.

Can I use eco-solvent Epson heads with UV ink?

No. Use the UV variant of the head with UV ink.

What happens if ink and lamp do not match?

Prints may stay tacky or poorly cured.

Do I need new profiles after changing ink?

Yes. Colour profiles are specific to ink, media and print mode.

Are Konica KM1024i variants interchangeable?

Variants differ in drop size and need matching settings. Check before replacing.

How do I confirm compatibility before buying?

Send photos, versions, head details and software information to the supplier and get written confirmation.

Do lamps need to match the chiller?

Yes. The chiller must handle the lamp’s heat output.

Can Unified Engineering Dynamics check compatibility?

Yes. Send details and photos and our team will help confirm compatible parts.

Are head data cables interchangeable between systems?

No. Cables differ in length, pin count, shielding and pinout. Use the type specified for your system and head.

Can I add white ink heads to my UV printer?

Only if your board system and software support the extra heads and you add a suitable ink system, often with circulation.

Can I use tap water in my UV lamp chiller?

No. Use the coolant recommended by the lamp and chiller makers to avoid scale, corrosion and algae.

Are used boards compatible?

They can be, but check versions, firmware, modifications and return terms, and test on arrival.

Do board versions change over time?

Yes. Versions, firmware and software change. Keep your profile current and plan upgrades when parts are discontinued.

Which UV printer configurations are easiest to support in India?

Common configurations with BYHX, Hoson or Senyang electronics and Ricoh Gen5 or Konica heads are widely supported by local traders.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *