UV Printing

UV Roll to Roll Head Driver Board Explained: How It Fires Ricoh, Konica and Kyocera Heads

UV Roll to Roll Head Driver Board: How It Fires Ricoh Heads

Direct answer: The UV roll to roll head driver board is the part of the printer’s electronics that generates and switches the high-voltage firing waveform that makes each piezo printhead eject ink. On some machines it is a separate plug-in board on the carriage; on others it is a driver section built into the head board or carriage board. It takes timing and data signals from the carriage board, applies the voltage and waveform set in the software for each Ricoh, Konica, Kyocera or Epson head, and switches that waveform to the right nozzles thousands of times a second. When it is healthy, drops are consistent; when it is weak or damaged, you see faded colours, missing nozzles, misdirected jets or, in the worst case, burnt heads.

Understanding the UV roll to roll head driver board helps you protect expensive Ricoh and Konica heads and diagnose weak or missing nozzles correctly.

UV Roll to Roll Head Driver Board: How It Fires Ricoh Heads
UV Roll to Roll Head Driver Board: How It Fires Ricoh Heads

Most owners of UV roll to roll printers know about printheads and carriage boards, but the head driver board is less familiar, even though it does some of the most demanding work in the machine. This guide explains what the driver board does, how it differs on UV machines, why it fails, and how to protect it. It follows on from our guide to the UV roll to roll carriage board, which covers the board it usually works alongside.

Where the head driver board sits

On a typical UV roll to roll printer, the carriage holds the printheads, the carriage board, adapter boards for each head, and the UV LED lamps at each end. The head driver function sits between the carriage board and the heads. Depending on the board system and head type, you may find:

  • A separate driver board plugged into the carriage board, sometimes one per pair of heads or per group of heads.
  • A driver section integrated into the carriage board, with power components and heat sinks on the same board.
  • Driver circuits on the adapter boards that sit directly above each head.

Chinese marketplaces list items such as a “BYHX G5 driver board” for Ricoh Gen5 printheads at around $200 to $220, alongside complete carriage boards, which shows that on some systems the driver function is a distinct, replaceable board. On others, it cannot be separated from the carriage board.

What the UV roll to roll head driver board does

Generates the firing waveform

Piezo printheads eject ink when a voltage pulse makes tiny piezo actuators flex, pushing ink out of each nozzle. The shape of that pulse, called the waveform, controls drop size, speed and stability. The driver board generates this waveform from a supply voltage, using power amplifiers that can deliver fast, precise pulses to many nozzles at once.

Applies the correct voltage for each head

Each Ricoh, Konica or Kyocera head has recommended drive settings. Technicians enter these in the print control software, often per head. The driver board applies those values. Too little voltage gives weak jetting and missing nozzles; too much stresses the head and the driver components and can shorten head life.

Switches the waveform to nozzles

The waveform must reach only the nozzles that should fire at that instant. Switching circuits, often inside the head itself and controlled by data from the board, decide which nozzles receive the pulse. The driver must supply enough current for every nozzle firing at the same moment, which is demanding when printing solid areas with all nozzles active.

Supports greyscale drop sizes

Ricoh Gen5 and Gen6 and Konica KM1024i heads can print several drop sizes. The waveform and data together control which drop size each nozzle produces. A driver board that cannot deliver clean waveforms affects greyscale quality, causing grainy gradients or banding.

Protects itself and the heads

Good driver designs include current limiting, temperature monitoring and fault detection. When something goes wrong, such as a shorted head, the protection may shut the channel down and report an error. Protection is not perfect, which is why procedures during head changes matter so much.

Why driver boards work harder on UV machines

Several factors make the driver board’s job more demanding on UV roll to roll printers than on many other wide-format machines:

FactorEffect on the driver board
Thicker UV inkHeads need correct temperature and drive settings to jet reliably; wrong settings push drivers harder
Industrial heads with many nozzlesRicoh Gen5 has 1,280 nozzles per head; high simultaneous firing loads
High production speedsHigher firing frequencies mean more heat in driver components
Lamp heat on the carriageDriver heat sinks start from a higher ambient temperature
White and varnish channelsMore heads and heavier ink loads on some channels
Static from film mediaDischarges can stress sensitive driver circuits

The driver board and head temperature

UV ink viscosity changes strongly with temperature. Ricoh and Konica heads have built-in heaters to bring ink to the jetting temperature recommended by the ink manufacturer. The driver settings are usually tuned for that temperature. If heads are colder than intended, the ink is thicker and drops become slower and smaller, so operators are tempted to raise the voltage. That can work for a while but puts extra stress on the driver and the head. The better fix is to restore correct heating. Our guide on Ricoh Gen5 head voltage and waveform settings for UV ink explains this relationship in detail.

Why head driver boards fail

Heat

Driver amplifiers dissipate heat every time they switch. Heat sinks and airflow remove it. On UV machines, lamp heat and hot rooms reduce the margin. Blocked fans, dusty heat sinks and poor ventilation lead to overheating, intermittent faults and eventually failed components. See our guide to UV LED lamp cooling and board overheating.

Shorted or damaged heads

A head with an internal short draws abnormal current from the driver. Protection may shut down the channel, but often the driver components fail first. This is the main reason a burnt driver channel is so often found after a failed head.

Hot-plugging and wrong connections

Connecting heads or cables with power on, or inserting flat cables at an angle, can send voltage to the wrong pins and damage driver components instantly.

Wrong settings

Driving heads at higher voltage than recommended, or using an unsuitable waveform, increases current and heat in the driver.

Power problems

Voltage fluctuation, poor earthing and surges stress the power supplies that feed the driver. A failing power supply can produce ripple or spikes that damage driver components. Our guide to UV roll to roll power fluctuation, stabilizers and earthing covers protection.

Ink and contamination

UV ink on driver boards and connectors, especially when partly cured by stray UV light, can cause leakage, poor contacts and corrosion.

Signs of a driver board problem

  • One head or group of heads printing faintly or with many missing nozzles, even after cleaning.
  • Misdirected jets or ink spray on one head that do not improve with maintenance.
  • Heads that work when cold but deteriorate as the machine warms up.
  • Error messages about head drive, voltage or overcurrent.
  • Visible damage, burning smell or discolouration on driver components or heat sinks.
  • A new head that fails soon after installation on the same channel.

Many of these symptoms can also come from heads, ink, air or settings, so careful diagnosis is essential. Our article on UV head driver board failure signs explains how to separate them.

Head driver board vs other boards

Owners often confuse the driver board with the head board and the mainboard. In short, the mainboard in the cabinet controls the whole machine and talks to the PC; the carriage or head board distributes data to the heads; and the driver board or driver section produces the firing waveform. On some machines, two of these functions share one board. Our guide to driver board vs head board vs mainboard covers the differences in detail.

Head types and their driver needs

HeadDriver considerations
Ricoh Gen5 / Gen5iPer-head drive settings; heater control; two-colour heads double the impact of one failed channel
Ricoh Gen6Higher frequencies; settings and waveforms must match the head and ink precisely
Konica KM1024iVariants with different drop sizes; driver must suit the variant
KyoceraHigh-end heads with specific driver electronics; usually manufacturer-specific
Epson i3200-U1Different driver architecture; common on smaller UV machines with Hoson or Senyang boards

Driver boards are generally specific to head type and board system. See our guide on UV driver board compatibility.

Protecting the head driver board

Daily

  • Confirm lamp cooling and carriage fans are working.
  • Check head temperatures reach set points before printing.
  • Run a nozzle check and note any head that looks weaker than usual.
  • Wipe visible ink from the carriage, keeping fluid away from boards.

Weekly

  • Check that heat sinks and fans on the carriage are free of dust and residue, with power off.
  • Inspect connectors for ink and loose seating.

Monthly

  • Have a technician check power supply voltages and earthing.
  • Review head drive settings against your records to ensure nobody has raised voltages to compensate for other problems.
  • Clean boards with an anti-static brush, power off.

During head changes

  • Always switch off and unplug.
  • Test heads for shorts before connection, especially used heads.
  • Enter correct settings before the first firing.

Our article on burnt Ricoh head boards after a head change covers safe procedures in detail.

Cost perspective

Driver boards and driver sections are much cheaper than the heads they drive. A BYHX G5 driver board was listed at about $200 to $220 on a Chinese marketplace in late 2026, while Ricoh Gen5 heads are listed at around ₹1.25 lakh to ₹1.55 lakh by Indian traders. A failing driver can destroy a new head, so diagnosing driver problems before fitting heads saves a great deal of money. Repair options are discussed in our article on UV driver board repair versus replacement.

Example: weak yellow that was a driver problem

A unit in Lucknow noticed that the yellow head on their four-head Ricoh Gen5 roll to roll printer printed faintly and lost nozzles during long jobs, although cleaning gave temporary improvement. The operator had already raised the yellow head’s voltage twice. A technician checked head temperature, ink supply and filters and found them normal. Measurements showed that the driver section feeding that head was producing a distorted waveform when warm, because a heat sink fan had failed. Replacing the fan and resetting the voltage to the recommended value restored normal jetting. Had the voltage been raised further, both head and driver could have been damaged.

Example: driver damage from a used head

Another unit fitted a used Ricoh head bought cheaply online. The head worked briefly, then the channel failed with an overcurrent error. Testing showed the head had developed an internal fault that overloaded the driver. The driver board was repaired, and the unit now tests all used heads before installation.

Inside the driver: the main building blocks

You do not need to be an electronics engineer to look after a driver board, but understanding its main blocks helps when a technician explains a fault or when you compare boards from different suppliers.

BlockWhat it doesWhat goes wrong
Input power and filteringReceives supply voltages from the power supply and smooths themCapacitor ageing, ripple from a failing power supply, blown fuses
High-voltage generationCreates the higher voltage used for the firing pulseOverheating, failed regulators, output drifting high or low
Waveform generatorShapes the pulse according to the waveform selected in softwareCorrupted settings, firmware mismatch, distorted pulses
Power amplifiersDeliver current to the head while keeping the pulse shape accurateHeat damage, failure after a head short, weak output under load
Protection and sensingMonitors current and temperature, shuts channels down on faultsFalse trips from noise, or failure to trip fast enough
ConnectorsLink the driver to the carriage board, power supply and headsInk contamination, burnt pins, loose seating from vibration

The power amplifiers and their heat sinks are usually the most obvious parts on the board. They are also the parts that fail most often, because they carry the highest current and run hottest. When a technician says a “channel” has failed, they usually mean the amplifier path feeding one head or one row of nozzles.

How the driver fits into one print pass

Following one pass of the carriage shows how closely the driver works with the rest of the electronics:

  1. The RIP software sends the processed image to the print control software, which sends it to the mainboard.
  2. The mainboard reads the encoder strip as the carriage moves and sends data for the right part of the image to the carriage board.
  3. The carriage board splits the data into streams for each head and colour.
  4. At each encoder position, the driver produces a firing pulse. The data decides which nozzles receive it and which drop size they make.
  5. The heads jet ink onto the media, and the UV LED lamps following the heads pin or cure the ink.
  6. The carriage returns or reverses, the media advances, and the cycle repeats.

A Ricoh Gen5 head can fire tens of thousands of times a second at high speed, and every firing passes through the driver. That gives a sense of how much work this board does in a single eight-hour shift, and why heat and component quality matter so much.

Questions to ask when buying a printer or a replacement driver

  • Is the driver a separate board, or part of the carriage board? This affects spare-part cost and stocking.
  • Which board system and version does the machine use, and is it still supported?
  • Are driver boards and carriage boards available in India, or only by import?
  • What cooling does the driver have: passive heat sinks, fans, or both?
  • What protection features does the board have against overcurrent and overheating?
  • Does the supplier provide the recommended voltage and waveform settings for your heads and ink?
  • Is there a warranty on boards, and what does it exclude?

Asking these questions before you buy a machine makes later maintenance and repairs much simpler. Our guide to the best UV roll to roll printer for business in India covers broader buying considerations.

Further reading: Industrial printheads use piezoelectricity: a voltage makes the actuator material flex and push ink out of the nozzle.

Key takeaways

  • The UV roll to roll head driver board generates and applies the firing waveform that makes piezo heads jet ink.
  • UV machines stress drivers with thick ink, many-nozzle heads, high speeds, lamp heat and static.
  • Heat, shorted heads, hot-plugging, wrong settings, power problems and ink contamination are the main causes of failure.
  • Do not raise head voltage to compensate for cold ink or other faults; fix the root cause.
  • Cooling, correct settings, good power and careful head changes protect both drivers and heads.

More in the UV head driver board series

Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.

Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine head driver board and the eco-solvent printer fire board.

Frequently Asked Questions

What is a head driver board on a UV printer?

It is the board or circuit that generates and applies the high-voltage firing waveform that makes piezo printheads eject ink. It may be a separate board or a section of the carriage board.

Is the head driver board the same as the head board?

Not always. On some machines the driver is a separate board; on others it is part of the head or carriage board. Both work together to fire the heads.

What happens if the driver board fails?

You may see weak or missing nozzles, misdirected jets, overcurrent errors, heads that fail when warm, or burnt components. A failing driver can also damage new heads.

Can I raise the head voltage to fix weak printing?

Only within recommended limits, and only after checking temperature, ink supply and maintenance. Raising voltage to hide other problems stresses heads and drivers.

Why does UV ink make driver settings more critical?

UV ink is thick and its viscosity changes strongly with temperature, so drive settings must match the head temperature and ink to jet reliably.

How much does a Ricoh Gen5 driver board cost?

A BYHX G5 driver board was listed at around $200 to $220 on a Chinese marketplace in late 2026, before shipping, duty and GST.

Can a shorted head damage the driver board?

Yes. A shorted head can draw abnormal current and burn driver components, which is why heads should be tested before connection.

How do I keep the driver board cool?

Keep carriage fans and heat sinks clean, ensure lamp cooling works and keep the room ventilated, especially in summer.

Are driver boards interchangeable between head types?

Generally no. Driver boards are specific to head type and board system. Always match brand, model and version.

Does static affect the driver board?

Yes. Static discharges from film media can stress sensitive driver circuits. Good earthing and anti-static brushes help.

Should driver boards be repaired or replaced?

Limited faults can often be repaired by skilled technicians, while extensive damage may need replacement. Always fix the root cause first.

Who can help diagnose driver board problems?

Unified Engineering Dynamics can help diagnose driver faults and supply compatible boards and heads for UV roll to roll printers.

Which part of the driver board fails most often?

The power amplifiers and their associated components, because they carry the highest current and run hottest, especially when cooling is poor or a head develops a short.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *