UV Printing

UV Head Driver Board Failure Signs on Ricoh and Konica Roll to Roll Printers

UV Head Driver Board Failure: 7 Signs on Ricoh and Konica

Direct answer: The main signs of UV head driver board failure on Ricoh and Konica roll to roll printers are: one head or a group of heads printing weakly or with many missing nozzles even after cleaning; misdirected or spraying jets on one channel; faults that appear as the machine warms up; overcurrent or head-drive error messages; burnt smells, discoloured components or hot heat sinks; and new heads failing soon after installation on the same channel. Because ink, air, temperature and head faults can cause similar symptoms, confirm a driver fault with temperature checks, head and cable swaps, and electrical measurements before buying parts.

Spotting UV head driver board failure early, and telling it apart from ink or head problems, protects your heads and shortens downtime.

UV Head Driver Board Failure: 7 Signs on Ricoh and Konica
UV Head Driver Board Failure: 7 Signs on Ricoh and Konica

Driver faults are tricky because the driver sits between the board and the head, and its symptoms look like head problems. This guide helps operators and technicians recognise when a driver is the likely cause, and what to check first. It builds on our explanation of the UV roll to roll head driver board and our guide to UV head board failure symptoms.

Sign 1: weak jetting that cleaning does not cure

When a head prints faintly or loses nozzles, the first steps should be cleaning, checking ink supply and filters, and checking head temperature. If those are normal and the head still prints weakly, a driver delivering low or distorted voltage becomes a suspect. Clues include:

  • Nozzle check shows many weak or bent lines across the whole head, not just in one area.
  • Cleaning gives brief improvement, but performance drops quickly once printing starts.
  • Raising voltage in software helps only slightly, or not at all.

Sign 2: faults that appear when warm

Driver components heat up during printing. A driver with a failing component, poor solder joint or blocked cooling may work when cold and fail when warm. Typical pattern: morning nozzle checks look good, but after 30 to 60 minutes of production a channel starts missing or spraying. Check fans, heat sinks and room temperature. Also note whether head temperature readings are normal, because heater faults can create similar time-related patterns.

Sign 3: overcurrent or head-drive errors

Many board systems report errors when a channel draws too much current or the driver detects a fault. These errors may come from a shorted head, a damaged cable or the driver itself. Do not repeatedly clear and retry; repeated attempts can increase damage. Switch off and investigate.

Sign 4: misdirected jets and spray on one channel

Distorted waveforms can produce drops that break up, form satellites or fly at angles. If one head shows heavy misdirection after thorough maintenance, and swapping the head to another channel cures it, suspect the driver channel.

Sign 5: visible damage

With power off and correct anti-static handling, inspect driver components for:

  • Discoloured or cracked components.
  • Burn marks around power devices.
  • Bulging capacitors.
  • Darkened PCB areas near heat sinks.
  • Melted connector housings.

Visible damage confirms a fault but not the root cause. Always look for what caused it.

Sign 6: new heads failing on the same channel

If a new head fails soon after installation, and the previous head on that channel also failed, the driver channel is a strong suspect. Stop fitting heads to that channel until it has been tested. Our article on why a bad driver board can damage new Ricoh heads explains why.

Sign 7: inconsistent density between passes

A driver struggling to supply current during heavy solid areas may produce lighter density in dense parts of the image or visible banding when many nozzles fire together. This can look like an ink supply problem, so check dampers, pumps and filters too.

Look-alike causes to rule out first

Look-alike causeHow it differsQuick check
Cold headsWeak jetting with low temperature readingsCheck heater and temperature display
Ink supply or airGradual loss, often during solid areas; air in dampersCheck dampers, filters, negative pressure
Cured ink on nozzle plateScattered missing nozzles; stray UV lightInspect plate, lamp shielding
Head wearGradual decline over monthsSwap head to another channel
Cable faultIntermittent, often with carriage movementSwap cable
Wrong settingsProblem began after a changeCompare with records

Our guide to UV curing problems and the article on UV ink systems, dampers and filters help rule out ink-related causes.

Step-by-step diagnosis of UV head driver board failure

  1. Record the symptom. Save nozzle checks and note time, temperature and media.
  2. Check head temperature and ink. Confirm heads reach set temperature and ink supply is normal.
  3. Check settings. Compare voltages and waveforms with your records.
  4. Swap heads between channels (power off). If the fault follows the head, the head is likely at fault. If it stays with the channel, suspect cable or driver.
  5. Swap cables. If the fault follows the cable, replace it.
  6. Check cooling. Inspect fans and heat sinks, and monitor whether the fault appears as the board warms.
  7. Measure. A technician can measure supply voltages and drive signals to confirm driver health.
  8. Test heads before refitting. If a driver failed, test the head on that channel for shorts.

Always switch off and unplug before handling heads and cables. See our guide to carriage board connectors and static handling.

Ricoh-specific notes

  • Ricoh Gen5 and Gen5i heads are often two-colour heads. A driver fault may affect both colours on one head, or one row depending on design.
  • Ricoh Gen6 heads fire at higher frequencies. Waveform and voltage must match the head and ink; incorrect settings can look like a driver fault.
  • Head temperature strongly affects jetting; check heater function first.

Konica-specific notes

  • Konica KM1024i comes in variants with different drop sizes. Make sure settings match the exact variant.
  • Some systems drive several Konica heads from one board, so a group fault points to a shared driver or cable.

What not to do

  • Do not keep raising voltage to compensate for weak jetting.
  • Do not clear overcurrent errors repeatedly without investigation.
  • Do not fit a new head to a suspect channel.
  • Do not hot-plug heads or cables.
  • Do not spray cleaning fluid onto boards.

Example: summer afternoon failures

A printer in Lucknow ran well each morning but lost nozzles on two heads every afternoon during May. The owner suspected the heads. Records showed failures started when the room passed 35ยฐC. A technician found a carriage fan running slowly and heat sinks coated with ink mist and dust. Cleaning, a new fan and better room ventilation solved the issue. The driver had been overheating, not failing permanently.

Example: overcurrent after a used head

A unit fitted a used Konica head to replace a failed one. Within minutes, an overcurrent error appeared. Rather than retrying, the technician tested the head and found an internal short. The driver channel was checked, found to have survived, and a tested head was fitted. Stopping at the first error saved the driver.

Reading the nozzle check for driver clues

The nozzle check is the most useful everyday tool for spotting driver problems early. Print one at the start of every shift and keep photos. Look for these patterns:

Nozzle check patternWhat it suggests
A few scattered missing nozzlesUsually ink, air, dust or cured ink; rarely the driver
A whole head faint, with lines thin across all nozzlesLow drive, cold head or ink supply; driver possible
One colour of a two-colour head affectedInk supply for that colour, or one driver path
Lines bent or doubled across one headWaveform distortion, wrong settings or nozzle plate damage
Block of nozzles missing in one sectionHead internal fault, cable pin or adapter board
Whole head blankCable, board channel, head failure or protection trip
Good when cold, worse laterHeat-related driver fault or heater problem

Comparing today’s nozzle check with last week’s often shows a slow decline that is invisible day to day. A driver channel that is slowly weakening will show a gradual thinning of lines on one head, while the other heads stay steady.

Using the error log

Most print control software keeps an error log. Check it whenever a head misbehaves. Useful entries include overcurrent warnings, head temperature errors, voltage errors and communication errors. Note the time of each error. If errors cluster after long runs or at the hottest time of day, heat is a likely factor. If they cluster when a heavy load starts elsewhere in the building, power quality may be involved. Take screenshots before clearing errors, because some systems overwrite older entries.

Temperature monitoring made simple

A low-cost infrared thermometer is a valuable tool. With lamps off and power isolated as required, measure heat sink temperatures on each driver channel after a production run. A channel that runs noticeably hotter than its neighbours, while driving similar heads at similar settings, deserves a closer look. Also log room temperature at the start and end of each shift. Over a few weeks, you will have a clear picture of how heat affects your machine.

Driver failure vs head failure: a comparison

CluePoints to headPoints to driver
Swap head to another channelFault moves with headFault stays with channel
Age of the partOld head, gradual declineSudden change after event
Nozzle patternBlocks or sections missingWhole head uniformly weak
Temperature dependenceUsually smallOften strong
Physical evidenceDamaged nozzle plate, ink inside connectorBurnt components, hot heat sink
HistoryHead struck by media, cured inkPrevious head failure on channel, surge

When to call a technician

Operators can safely do cleaning, nozzle checks, temperature checks, settings comparisons and visual inspection with power off. Call a qualified technician when:

  • Swap tests point to a driver channel.
  • There is any sign of burning, smoke or melted parts.
  • Overcurrent errors repeat.
  • A head has failed and a replacement is about to be fitted.
  • Electrical measurements are needed.

Give the technician your nozzle check photos, error log screenshots, temperature notes and a list of what you have already tried. This shortens diagnosis and reduces cost.

Preventing the next failure

Once a driver fault is fixed, take steps so it does not return. Clean or replace carriage fans, set up a weekly heat sink cleaning routine, check that voltages are back to recommended values, review earthing and power protection, and train operators never to hot-plug. Our guide to power fluctuation, stabilisers and earthing and our article on lamp cooling and board overheating cover the two most common root causes.

Common causes behind the signs

Recognising the sign is half the job; the other half is understanding the cause so the fault does not return.

Underlying causeSigns it tends to producePrevention
Blocked carriage fan or dirty heat sinkWarm-up failures, hot channelWeekly cleaning, fan checks
Hot print roomAfternoon and summer failuresVentilation or air conditioning
Lamp cooling problemsCarriage heat, faults on long runsChiller maintenance
Head internal shortOvercurrent errors, sudden channel failureTest heads before fitting
Surge or poor earthingFailures after storms or power eventsStabiliser, surge protection, earthing
High voltage settingsGradual driver decline, hot channelsKeep settings near label values
Ink contaminationIntermittent faults, corrosionFix leaks, clean, shield boards
Hot-pluggingSudden failure after maintenanceStrict power-off rule

A simple daily routine that catches driver problems early

  1. Before power-up, look at the carriage: any ink on boards, any loose cables, any obvious damage?
  2. Power up in the correct order and wait for heads to reach temperature.
  3. Check that carriage fans are running and chiller readings are normal.
  4. Print a nozzle check and save a photo with the date.
  5. Compare it with yesterday’s check, paying attention to any head that looks weaker.
  6. Midway through the shift, print another nozzle check to catch heat-related changes.
  7. Note any errors in a logbook, with time and room temperature.

This routine takes a few minutes and creates a record that makes diagnosis far easier when something does go wrong.

Signs in the print itself

Sometimes the first sign of a driver problem appears in customer jobs rather than nozzle checks:

  • Gradually weaker colour in one channel, noticed as colour drift between jobs.
  • Fine banding in solid areas that varies with job density.
  • Grainy gradients where smooth tones used to be.
  • White underbase losing opacity on backlit film, if the white channel is affected.

When colour drifts and recalibration only helps briefly, check driver health and settings as well as ink and lamps. Our guide on Ricoh Gen5 head voltage settings explains how drive affects density.

Documenting a suspected driver fault

If you need to involve a supplier or claim warranty, documentation matters. Collect nozzle check photos before and after the fault, error log screenshots, photos of the board and heat sinks, a record of swap tests and their results, settings at the time of failure, and room temperature notes. A clear record helps suppliers agree quickly on whether the board, head or another factor was responsible.

Quick reference card for operators

Print this list and keep it beside the machine:

  • Weak head after cleaning? Check temperature, ink and filters, then report.
  • Head fails only after warm-up? Check fans and room temperature, then report.
  • Overcurrent error? Switch off. Do not clear and retry.
  • Burning smell? Switch off and isolate power immediately.
  • New head failed? Do not fit another until the channel is tested.
  • Never unplug or plug head cables with power on.
  • Save nozzle check photos and error screenshots every time.

Clear rules like these mean that whoever is on shift responds the same way, which protects heads and boards and gives your technician the information needed for a fast diagnosis.

Further reading: This routine follows standard troubleshooting logic: rule out simple causes first, then isolate the faulty part.

Key takeaways

  • Weak jetting after cleaning, warm-up failures, overcurrent errors, misdirection and repeated head failures are signs of UV head driver board failure.
  • Rule out temperature, ink, head wear, cables and settings first.
  • Swap tests show whether faults follow heads, cables or channels.
  • Stop at overcurrent errors and investigate.
  • Never fit new heads to a suspect channel.

More in the UV head driver board series

Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.

Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine head driver board and the eco-solvent printer fire board.

Frequently Asked Questions

How do I know if my UV head driver board is failing?

Look for weak jetting after cleaning, faults when warm, overcurrent errors, misdirected jets on one channel, visible damage and repeated head failures on the same channel.

Can a bad head look like a driver fault?

Yes. Swap heads between channels to see whether the fault follows the head or stays with the channel.

Why do faults appear only after the printer warms up?

Failing components and blocked cooling cause problems at higher temperatures. Check fans, heat sinks and room temperature.

What should I do when I see an overcurrent error?

Switch off and investigate. Repeatedly clearing the error can increase damage to heads and drivers.

Can I fix weak jetting by raising voltage?

Only within recommended limits after checking temperature and ink. Raising voltage to hide faults stresses heads and drivers.

Do Ricoh two-colour heads show driver faults differently?

A driver fault may affect both colours or one row, depending on design. Check both colours on nozzle checks.

Can ink supply problems look like driver faults?

Yes. Air in dampers, blocked filters and pressure problems cause weak or missing nozzles, so check the ink system first.

Is it safe to fit a new head after a driver failure?

Only after the driver channel has been tested or repaired and the root cause fixed.

Can static damage driver boards?

Yes. Static from film media and poor handling can damage sensitive driver components.

How long does a driver board last?

With good cooling, clean power and correct settings, driver boards can last years. Heat and head faults shorten life.

Should I repair or replace a failed driver board?

Limited faults are often repairable. Extensive damage may need replacement. See our repair vs replacement guide.

Can Unified Engineering Dynamics test driver boards?

Yes. Our team can help diagnose driver faults and supply compatible replacements for UV roll to roll printers.

How can a nozzle check reveal a driver fault?

A driver fault often makes a whole head uniformly faint or distorted, while ink and dust problems usually cause scattered missing nozzles. Comparing checks over time reveals slow decline.

Is an infrared thermometer useful for driver diagnosis?

Yes. Comparing heat sink temperatures between channels after a run can reveal a channel that is running hotter than normal.

Can driver problems show up as colour drift?

Yes. A weakening driver channel can gradually reduce density in one colour, causing colour drift that recalibration only fixes briefly.

Can an operator diagnose a driver fault without a technician?

Operators can do cleaning, temperature checks, settings comparisons and swap tests with power off. Electrical measurement and repair should be done by a qualified technician.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *