Direct answer: Ricoh Gen5 head voltage and waveform settings control how hard and in what pattern each nozzle’s piezo actuator is driven, which sets drop size, drop speed and jetting stability with UV ink. Each Ricoh head is supplied with a recommended drive voltage, often printed on the head label or test sheet, and the waveform is chosen in the print control software to suit the head and the UV ink. The right settings depend on head temperature, ink viscosity and print mode. Keep heads at the ink maker’s recommended temperature, use the recommended voltage as a starting point, adjust only in small steps when needed, and record every change. Raising voltage to hide cold ink, air or blocked filters is the most common mistake and shortens head and driver life.
Correct Ricoh Gen5 head voltage settings give stable jetting with UV ink and protect both heads and driver boards from unnecessary stress.

Table of Contents
This guide explains voltage and waveform for Ricoh Gen5 and Gen6 heads on UV roll to roll printers, with practical advice for operators and technicians. It does not replace your board system’s manual, ink maker’s guidance or head documentation, which take priority. It links to our guides on the UV roll to roll head driver board and how UV ink curing works.
What Ricoh Gen5 head voltage means
Ricoh Gen5 heads use piezo actuators that flex when voltage is applied. The peak voltage of the drive waveform determines how far each actuator flexes and therefore how much energy goes into each drop. Higher voltage gives larger, faster drops; lower voltage gives smaller, slower drops. Too low, and drops may not leave the nozzle reliably. Too high, and drops may break into satellites, spray, or flood the nozzle plate, while heads and drivers run hotter.
The head label voltage
Ricoh heads are tested at the factory, and each head’s recommended voltage is typically provided on its label or accompanying sheet. Because heads vary slightly, each may have a different value. When fitting a head, enter its specific value into the software for that channel before first firing. Using another head’s value is a common error.
What the waveform does
The waveform is the shape of the voltage pulse over time, including rise, hold and fall. It is designed to push ink out, then retract the meniscus cleanly so the next drop forms properly. Waveforms are matched to head type, ink viscosity, firing frequency and drop size mode.
- Greyscale waveforms produce small, medium and large drops by combining pulses.
- Frequency affects which waveform is suitable; high-speed modes need waveforms that settle quickly.
- Ink-specific waveforms may be supplied by ink makers or board suppliers for particular UV inks.
Most operators should not edit waveforms. Select the waveform recommended by the board supplier or ink maker for your head and ink, and adjust voltage within recommended limits.
Temperature: the most important partner to voltage
UV ink is thick at room temperature and thins as it warms. Ricoh heads have internal heaters controlled by the head board, and the ink maker specifies a jetting temperature range. Drive settings assume heads are within that range.
| Head temperature | Ink viscosity | Effect on jetting | Wrong reaction | Right reaction |
|---|---|---|---|---|
| Below target | Too high | Weak, slow drops; missing nozzles | Raise voltage | Fix heating; wait for warm-up |
| At target | Correct | Stable jetting at recommended voltage | — | Keep settings |
| Above target | Too low | Satellites, spray, flooding | Lower voltage a lot | Check heater control and room temperature |
In Indian winters, especially in north India, rooms can be cold in the morning. Allow heads to reach temperature before printing. In summer, hot rooms and lamp heat can push ink temperatures up. Our installation and room checklist covers environment control.
When to adjust voltage
Voltage adjustment is appropriate when:
- Fitting a new head (enter its label value).
- Balancing density between heads of the same colour after calibration.
- Changing to a new ink that the ink maker says needs different settings.
- Following a technician’s calibration procedure.
Voltage adjustment is not appropriate as a first response to:
- Missing nozzles that cleaning or ink system checks could fix.
- Weak jetting caused by cold heads.
- Air in dampers or blocked filters.
- Cured ink on the nozzle plate from stray UV light.
Safe adjustment practice
- Confirm heads are at target temperature and ink supply is normal.
- Record the current settings before changing anything.
- Adjust in small steps, as advised by your board supplier.
- Print nozzle checks and density patches after each step.
- Stop if jetting does not improve; look for another cause.
- Never exceed limits specified by the head maker, board supplier or ink maker.
- Record the final settings, date and reason.
Gen5 vs Gen6 differences
| Aspect | Ricoh Gen5 | Ricoh Gen6 |
|---|---|---|
| Native drop size (approx.) | About 7 pl minimum with greyscale | About 5 pl minimum with greyscale |
| Firing frequency | Lower | Higher; supports faster printing |
| Waveform sensitivity | Moderate | Higher; waveform must suit head and ink |
| Board needs | Gen5 support | Gen6 support required |
Drop size and frequency figures vary by variant and mode; always check current Ricoh documentation. Our comparison of Ricoh Gen5 vs Gen5i covers variants.
Voltage, heat and driver life
Higher voltages mean more energy per firing, more heat in the driver and more stress on head actuators. Machines run with consistently high voltages, often because of uncorrected temperature or ink problems, tend to see more driver failures and shorter head life. Keeping voltage near recommended values is one of the simplest ways to protect both. See our article on how a bad driver board damages Ricoh heads.
White and varnish channels
White UV ink contains heavy pigments and is circulated to prevent settling. Varnish has different viscosity from colour inks. These channels may need different settings, and the ink maker’s recommendations are especially important. Good white ink circulation keeps viscosity consistent; see our guide to UV white ink circulation.
Keeping a settings record
| Field | Example |
|---|---|
| Date | 12 November |
| Channel / colour | Head 2, magenta/yellow |
| Head serial | From label |
| Label voltage | From label |
| Set voltage | Current value |
| Waveform | Name from software |
| Head temperature set point | From ink maker |
| Reason for change | New head fitted |
| Changed by | Technician name |
Example: winter mornings and rising voltages
A unit in Lucknow found that over one winter operators had raised voltages on all four heads well above label values to deal with weak morning printing. In spring, the heads began spraying and one driver channel failed. A technician reset voltages to label values, repaired the driver and set a rule: wait for heads to reach temperature before printing. Morning problems disappeared once the warm-up rule was followed.
Example: new ink, new waveform
Another unit switched UV ink brands to cut costs. Jetting became unstable. The new ink maker supplied a recommended waveform and temperature for Ricoh Gen5. After loading those settings and flushing the old ink properly, jetting returned to normal. Changing ink without changing settings is a common cause of instability.
Drop size, greyscale and print modes
Ricoh Gen5 and Gen6 heads can produce several drop sizes from the same nozzle. The print control software chooses a waveform set and print mode that determine which drop sizes are used. In general:
- High-quality modes use smaller drops and more passes for smooth gradients and fine text, ideal for backlit film and close-viewing graphics.
- Production modes use larger drops and fewer passes for speed on banners and large-format vinyl.
- White and varnish modes may use specific drop sizes and densities for opacity or gloss effects.
Voltage interacts with drop size. A head set too low may produce small drops that are barely visible, while large drops still appear acceptable. That is why density calibration and nozzle checks should be done in the mode you use most.
Balancing heads of the same colour
On machines with two or more heads per colour, slight differences in head output can cause visible bands where each head prints. Technicians balance heads by printing density patches from each head and adjusting voltages slightly so their output matches. Good practice:
- Ensure all heads are clean, at temperature and jetting fully.
- Print a density test for each head individually.
- Measure or visually compare the patches under consistent light.
- Adjust the stronger or weaker head in small steps, staying close to its label value.
- Reprint and check, then record final values.
If one head needs a much larger adjustment than the others, suspect a problem with that head, its driver channel or its ink supply rather than continuing to adjust.
Firing frequency and speed
Higher printing speeds require heads to fire more often. At high frequencies, the meniscus has less time to settle between drops, and waveform design becomes critical. Gen6 heads are designed for higher frequencies than Gen5. Pushing a Gen5 head beyond the frequencies its waveform supports can cause unstable jetting, satellites and misdirection. If problems appear only in your fastest mode, try the next slower mode before blaming hardware.
Ink viscosity and the ink data sheet
Every UV ink has a data sheet stating its viscosity at specific temperatures and recommended jetting conditions. Request this from your ink supplier. It tells you:
- The recommended head temperature range.
- Viscosity at that temperature.
- Recommended waveform or settings for common heads, if available.
- Lamp wavelength and energy needed to cure.
- Storage and shelf-life conditions.
Ink stored in very cold or very hot conditions can behave differently. Keep ink in a cool, dark place and let new bottles reach room temperature before loading. Our UV ink handling and safety guide covers storage.
Troubleshooting by symptom
| Symptom | First checks | Possible setting issue |
|---|---|---|
| Weak, thin lines on one head | Temperature, ink supply, filter | Voltage below label value |
| Spray and satellites | Head temperature too high, nozzle plate condition | Voltage too high or wrong waveform |
| Missing nozzles at high speed only | Ink supply under heavy load | Waveform not suited to frequency |
| Banding between heads | Head alignment, feed calibration | Heads not balanced |
| Unstable after ink change | Flushing, ink compatibility | Waveform and temperature not updated |
| Nozzle plate flooding | Negative pressure, damper | Voltage too high |
Who should change settings
Head settings affect expensive components. Many units restrict access so only trained technicians or supervisors can change voltage and waveform. Print control software may support passwords or user levels. If not, keep a written rule and a log. Untracked changes by different operators on different shifts are a major source of mysterious problems.
A step-by-step new-head setup for Ricoh Gen5
When fitting a new Ricoh Gen5 head on a UV roll to roll printer, this sequence brings voltage, waveform and temperature together correctly. Follow your board system’s manual where it differs.
- Record the new head’s serial number and label voltage.
- Confirm the driver channel has been checked if the previous head failed.
- With power off, fit the head mechanically and connect cables carefully.
- Power up and, before any firing, enter the label voltage for the channel in the software.
- Confirm the correct waveform is selected for the head and ink.
- Prime the head with ink following the supplier’s procedure.
- Wait until the head reaches its set temperature.
- Print a nozzle check and inspect it carefully.
- Perform head alignment: vertical, bidirectional and head-to-head.
- Print density patches and balance against other heads of the same colour if needed.
- Recalibrate colour profiles if density has changed noticeably.
- Record all settings in the log.
Temperature settings in practice
The ink maker specifies a jetting temperature range, and the head board holds heads at the set point. Several practical points help:
- Set the same temperature for all heads using the same ink, unless your supplier recommends otherwise.
- Check that displayed temperatures are stable during printing. Large fluctuations suggest heater or thermistor problems.
- If one head consistently reads differently from others with the same set point, check its heater and thermistor wiring.
- Remember that ink in supply lines and dampers may be cooler than in the head in a cold room. Some machines have ink line heaters for this reason.
A head that cannot reach temperature is a head board or heater fault, not a reason to raise voltage. Our guide to UV head board failure symptoms covers heater faults.
Seasonal adjustments in India
India’s climate swings widely through the year, and print rooms without climate control feel it:
| Season | Typical challenge | Recommended response |
|---|---|---|
| Winter (north India) | Cold mornings; thick ink in lines | Longer warm-up; keep ink in warmer area; do not raise voltage |
| Summer | Hot rooms; lamp heat; ink thinner | Ventilation; check chiller; watch for spray |
| Monsoon | High humidity; condensation risk | Avoid very cold chiller set points; keep media dry |
Keeping the room within a moderate temperature band all year is the best way to keep voltage settings stable. Many shops find that a simple air conditioner pays for itself in fewer problems and less ink waste.
Voltage settings and warranty
Head and board suppliers may ask what settings were used when a head fails. Settings far above recommended values can affect warranty decisions. Keeping records showing you used label voltages and recommended waveforms supports any claim and demonstrates good practice.
Common myths about head voltage
| Myth | Reality |
|---|---|
| Higher voltage always gives better colour | Above the right level, it causes spray, satellites and faster wear |
| All heads of a model use the same voltage | Each head has its own recommended value |
| Voltage fixes missing nozzles | Most missing nozzles come from ink, air, dust or cured ink |
| Waveforms are universal | Waveforms are matched to head type, ink and frequency |
| Temperature does not matter once the head is warm | Small temperature changes alter UV ink viscosity and jetting |
Clearing up these myths with your team prevents the gradual voltage creep that shortens head and driver life on so many machines.
Further reading: UV ink viscosity falls as temperature rises, which is why head temperature and drive settings must be considered together.
Key takeaways
- Ricoh Gen5 head voltage controls drop energy; waveform controls drop formation.
- Use each head’s label voltage and the recommended waveform for your head and ink.
- Head temperature is critical; fix heating before touching voltage.
- Adjust in small steps, never exceed limits, and record every change.
- High voltages shorten head and driver life.
More in the UV head driver board series
- UV Roll to Roll Head Driver Board Explained
- Head Driver Board vs Head Board vs Mainboard
- UV Head Driver Board Failure Signs
- Why a Bad Driver Board Can Kill a New Ricoh Head
- UV Driver Board Compatibility: Ricoh, Konica, Kyocera, Epson
- UV Driver Board Repair vs Replacement
- Power Fluctuation: Stabilizer, UPS and Earthing
- UV LED Lamp Cooling, Chillers and Board Overheating
Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.
Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine head driver board and the eco-solvent printer fire board.
Frequently Asked Questions
Where do I find the correct voltage for a Ricoh Gen5 head?
Ricoh heads usually come with a recommended voltage on the label or test sheet. Enter that value for the head’s channel before first firing.
Can I use the same voltage for all heads?
Not necessarily. Each head can have a different recommended value. Use each head’s own value.
Why is my head printing weakly in the morning?
Cold heads make UV ink thick. Wait for heads to reach set temperature before printing rather than raising voltage.
Should I change the waveform myself?
Most operators should use the waveform recommended by the board supplier or ink maker and not edit waveforms.
Does changing UV ink require new settings?
Often yes. Ask the ink maker for recommended temperature and waveform settings for your head.
What happens if voltage is too high?
Drops may spray or form satellites, nozzle plates may flood, and heads and drivers run hotter and wear faster.
What happens if voltage is too low?
Drops may be weak or fail to eject, causing missing nozzles and light density.
Are Gen6 settings different from Gen5?
Yes. Gen6 heads need Gen6-compatible boards, waveforms and settings.
Do white ink heads need different settings?
White and varnish inks may need different settings. Follow the ink maker’s guidance.
How should I record settings?
Keep a log of head serials, label and set voltages, waveforms, temperatures, dates and reasons for changes.
Can wrong settings damage a head?
Settings far outside recommended limits can stress heads and drivers and shorten their life.
Can Unified Engineering Dynamics help set up Ricoh heads?
Yes. Our team can advise on head installation and settings for UV roll to roll printers.
How do I balance two heads of the same colour?
Print density patches from each head, compare them, and adjust voltages in small steps near label values until output matches. Large differences suggest a hardware problem.
Why does my printer only have problems in the fastest mode?
High firing frequencies demand waveforms that settle quickly. If the waveform does not suit the frequency, jetting becomes unstable. Try a slower mode.
Do I need to realign heads after changing voltage?
Significant voltage changes can alter drop speed and placement, so check alignment after any large change and always after fitting a new head.
Why does one head show a different temperature from the others?
It may have a heater or thermistor fault, or a wiring problem. Check it rather than compensating with voltage.
Can I copy voltage settings from another printer?
No. Each head has its own recommended value, and ink, temperature and board settings may differ between machines.