Direct answer: A UV main board replacement involves more than swapping a board. Before ordering, confirm the board system, version, head type, head count and firmware with your supplier using photos. Before removal, back up every setting and calibration file, record firmware and software versions, note licence and dongle details, and photograph and label every cable. After fitting, check firmware compatibility with the carriage board, transfer or reactivate the print control software licence if it is tied to the board, restore settings, re-enter head voltages, and recalibrate alignment, feed and colour. The RIP licence is usually tied to the PC or a separate dongle, but confirm this before you start.
A planned UV main board replacement takes hours; an unplanned one can take days, mostly because of licences and lost settings.

Table of Contents
Main board replacement is a significant job on a UV roll to roll printer. Done carefully, it takes a few hours. Done carelessly, it can mean days of lost production, licence problems and recalibration. This checklist covers BYHX, Hoson, Senyang and similar systems. It follows our guides to UV main board failure symptoms and firmware updates.
Step 1: confirm the main board really needs replacing
Many main boards are replaced unnecessarily. Before ordering:
- Check all power supply outputs.
- Swap PC cables and try another PC.
- Check the internal data link to the carriage.
- Check encoder, sensors and servo drivers.
- Restore settings if problems began after an update.
- Inspect the board for damage.
- Consider repair for limited damage such as a broken port.
Step 2: identify the exact board
- Photograph both sides of the board, labels, part numbers and version numbers.
- Record print control software name and version.
- Record head type, variant and number of heads.
- Record carriage board model and version.
- Send all details to the supplier and get written confirmation of compatibility.
Our guide to BYHX vs Hoson vs Senyang main boards helps with identification.
Step 3: understand licences and dongles
| Licence type | Typically tied to | What to check |
|---|---|---|
| Print control software | Main board, dongle or both, depending on system | Whether new board needs activation or licence transfer |
| RIP software | PC or separate USB dongle | Usually unaffected by main board change; confirm |
| Machine-specific features | Board serial or code | Whether features such as white or varnish need re-enabling |
Some systems use a code or file linked to the board serial number. The supplier may need your old board details to issue a new code. Ask about this before ordering, especially if the machine came from a reseller who controls the licence.
Step 4: back up everything
- Export settings and calibration files from the print control software.
- Photograph every settings screen: head voltages, temperatures, alignment, feed, lamps, white ink circulation, media settings.
- Back up RIP profiles, colour profiles and media settings.
- Note firmware versions of all boards.
- Note IP settings if Ethernet is used.
If the old board is dead, some settings may be lost. Records and photos taken earlier become invaluable.
Step 5: remove the old board safely
- Switch off and unplug the printer. Wait for capacitors to discharge.
- Wear an earthed anti-static wrist strap.
- Photograph the board with cables connected from several angles.
- Label each cable with its connector name.
- Unplug cables carefully, releasing locks.
- Remove mounting screws and lift the board without flexing it.
- Place it in an anti-static bag.
Step 6: fit the new board
- Inspect the new board for transit damage.
- Check any jumper or DIP switch settings against the old board.
- Mount it securely using the original standoffs.
- Reconnect cables one by one, using labels and photos, fully seated and locked.
- Double-check power connector polarity and positions.
Step 7: power up and configure
- Power up and watch for normal LEDs and initialisation.
- Connect to the PC; install or update software if needed.
- Check firmware versions; update only if the supplier advises, following safe practice.
- Activate or transfer licences.
- Restore settings from backup or re-enter them from photos.
- Enter correct head voltages for each head before firing.
- Check head temperatures, lamps and white ink circulation.
Step 8: calibrate and test
- Run initialisation and confirm carriage moves correctly.
- Print nozzle checks.
- Calibrate head alignment, bidirectional and feed.
- Check density and colour; re-profile if needed.
- Run test jobs on your main media before production.
Common problems after UV main board replacement
| Problem | Likely cause | Fix |
|---|---|---|
| Software says unlicensed | Licence tied to old board | Contact supplier for activation |
| Carriage board not recognised | Firmware mismatch | Update firmware as supplier advises |
| Carriage moves wrong direction | Settings not restored, motor parameters | Restore machine parameters |
| Heads print weakly | Voltages at defaults | Enter label voltages |
| Lamps do not switch on | Lamp settings or wiring | Check lamp parameters and connectors |
| White or varnish disabled | Feature not enabled | Ask supplier to enable |
Costs to plan for
Main board prices vary by system, head type and head count. Indicative prices seen in late 2026 range from around $180โ210 for a BYHX double-head main board to around $845โ866 for a BYHX Gen5 4-head main board and around $1,420 for a Gen6 main board from a Chinese supplier, before shipping, duty and GST. Add technician time, possible licence fees and downtime. See our guide to UV roll to roll main board prices in India.
Example: licence surprise
A unit replaced a failed main board bought from a different trader. The new board worked, but the print control software showed it as unlicensed. The original machine reseller had the licence details and charged a fee to issue a new code. Asking about licensing before ordering would have avoided the delay.
Example: smooth replacement
A Lucknow unit kept photos and backup files of all settings. When their main board failed after a storm, the supplier confirmed compatibility from photos, the board arrived in four days, and installation, licence activation and calibration took one afternoon.
Preparing in advance: a main board readiness kit
The best time to prepare for a main board replacement is while the machine is healthy. A readiness kit includes:
- Photos of the main board, carriage board and all cables in place.
- A cable labelling scheme applied to all connectors.
- Exported settings and calibration files, updated after every major calibration.
- Screenshots of every settings screen.
- Records of board part numbers, versions and firmware.
- Licence details, codes and dongle information.
- Supplier contacts for boards, software and licences.
Store copies on the PC, a USB drive and cloud storage so that a PC failure does not wipe them out.
Jumpers, DIP switches and configuration
Some main boards have jumpers or DIP switches that set options such as machine width, head configuration or communication mode. A new board may arrive with default settings. Compare carefully with the old board and photos before powering up. Wrong settings can cause confusing behaviour or, in rare cases, damage.
Working with the machine supplier or reseller
If your machine came from a reseller, they may control software licences, machine parameters and firmware files. Contact them early when a main board fails. Ask whether they can supply a pre-configured board, which can save time, and whether they will remotely assist with activation and settings. Keep your relationship with the reseller in good order; their cooperation can make a big difference during a failure.
Machine parameters you must not forget
| Parameter | Why it matters |
|---|---|
| Machine width and print area | Wrong values can crash carriage |
| Motor direction and speed parameters | Carriage and feed movement |
| Encoder resolution | Drop placement accuracy |
| Head configuration and order | Colours print in correct positions |
| Head voltages and temperatures | Jetting stability and head safety |
| Lamp settings | Curing quality |
| White ink circulation | Prevents settling |
| Feed calibration | Banding control |
Losing machine parameters is often more painful than losing calibration, because they may only be available from the machine maker.
After the job: update your records
Once the new board is installed and calibrated, update your readiness kit: new part numbers, firmware versions, licence codes, new settings exports and photos. Label the old board clearly if it will be repaired as a spare.
Timeline of a typical replacement
| Stage | Typical time |
|---|---|
| Diagnosis and confirmation | A few hours to a day |
| Identifying board and getting quotes | Same day if records are ready |
| Delivery | Same day to several days locally; one to three weeks for imports |
| Removal and installation | One to two hours |
| Software, firmware and licence | One hour to several days if licence issues arise |
| Settings and calibration | Two to six hours |
| Test printing | One to two hours |
Preparation reduces most of these stages. The biggest variables are delivery time and licence activation.
Safety during replacement
- Power supplies can hold dangerous charge after switch-off; wait as advised and avoid touching power supply terminals.
- Use an earthed anti-static wrist strap.
- Keep metal tools away from live parts if any testing is done with power on.
- Wear gloves if handling ink-contaminated parts.
- Do not work alone on live electrical tests.
Testing the old board
Once the new board is working, send the old board for assessment. If it can be repaired, keep it as a tested spare. If it cannot, record the failure cause to guide prevention. A spare main board, even a repaired one, can turn a future failure from days of downtime into a few hours.
Preventing the next failure
Ask why the board failed. Common causes include surges, poor earthing, cabinet heat and dust, and hot-plugging. Fix these before restarting production. Our guide to surge and lightning protection and our article on power fluctuation and earthing cover the most common causes.
Replacement with a different version
Sometimes the exact board version is no longer available, and the supplier offers a newer version. This can work, but usually requires checking:
- Whether the carriage board firmware must be updated to match.
- Whether the print control software needs a newer version.
- Whether connectors, cables and power requirements are the same.
- Whether settings files from the old version can be imported.
- Whether the licence covers the new version.
Get written confirmation on each point. A newer board can also bring benefits, such as improved stability or support for future head upgrades, but plan for extra setup time.
Example: newer version, smooth result
A unit in Kanpur could not find their exact main board version. The supplier offered the current version with matching carriage board firmware and a software update. Because the supplier provided a clear sequence and the unit had good backups, installation and calibration took one day, and the machine has run reliably since.
Cost checklist for a replacement
- Main board price and landed cost.
- Any additional cables, adapters or carriage board firmware updates.
- Software update or licence fees.
- Technician time for installation and calibration.
- Test ink and media.
- Production lost during downtime.
Listing all costs in advance helps you choose between local and imported boards, and between repair and replacement. Our guide to UV roll to roll main board prices gives indicative figures.
Documenting the replacement for warranty
Record the date, the board’s serial number, the supplier, the invoice, photos of installation and the tests performed. If the new board fails during its warranty period, this record supports a quick claim. Note also any changes to firmware, software and settings, so the next technician knows exactly what was done.
Bottom line
A UV main board replacement is straightforward when you prepare in advance: confirm the fault, identify the exact board, understand licensing, back up settings, label cables and recalibrate carefully. Without preparation, the same job can take days. Build your readiness kit today, while the machine is working.
Further reading: Print control software is protected by a software licence that may be tied to the board or a dongle.
Key takeaways
- Confirm the main board is really faulty before a UV main board replacement.
- Identify the exact board and get written compatibility confirmation.
- Check licence and dongle arrangements before ordering.
- Back up settings and photograph and label all cables.
- Restore settings, enter head voltages and recalibrate before production.
More in the UV main board series
- UV Roll to Roll Main Board: Functions and Ports
- UV Main Board Failure Symptoms
- BYHX vs Hoson vs Senyang Main Boards for UV
- UV Main Board Firmware Update Guide
- Ricoh Gen5 to Gen6 Upgrade: Is It Worth It?
- UV Printer Connection Problems: USB, Network, Fibre
- UV Printer Surge and Lightning Protection
- UV Roll to Roll Main Board Price in India
- Used UV Roll to Roll Printer Electronics Check
Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.
Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine main board and the eco-solvent printer main board.
Frequently Asked Questions
Will my software licence work with a new main board?
It depends on the system. Some licences are tied to the board or a dongle. Ask your supplier before ordering.
Is the RIP licence affected by main board replacement?
Usually not, because RIP licences are typically tied to the PC or a separate dongle. Confirm with your RIP supplier.
Do I need to recalibrate after replacing the main board?
Yes. Check head voltages, alignment, feed and colour before production.
What should I back up before replacement?
Settings, calibration files, head voltages, colour profiles, media settings, firmware versions and IP settings.
Can I replace the main board myself?
Trained technicians can, following anti-static and safety procedures. Licence activation may need supplier support.
Why does the new board not recognise the carriage board?
Firmware versions may be incompatible. Ask the supplier which versions to use.
How long does main board replacement take?
With preparation, installation and calibration can take a few hours. Licence issues can add delays.
Should I repair rather than replace the main board?
Limited damage such as a broken port or power input fault is often repairable. Extensive damage may need replacement.
What if my old board is dead and settings are lost?
Use photos and records taken earlier, or recalibrate from scratch with a technician.
Can I use a main board from another system?
No. Main boards must match the board system, version, heads and software.
Does replacing the main board change head settings?
Settings may reset. Always enter correct head voltages before firing.
Can Unified Engineering Dynamics supply main boards?
Yes. Our team can help confirm compatibility and supply main boards for UV roll to roll printers.
What is a main board readiness kit?
A collection of photos, labels, settings exports, version records, licence details and supplier contacts prepared while the machine is healthy, ready for any board replacement.
Can a supplier send a pre-configured main board?
Some suppliers and resellers can pre-configure boards with your machine parameters and licence, which saves time. Ask when ordering.
How long does a main board replacement take overall?
With good preparation and local stock, it can be done in a day. Imports and licence issues can extend it to weeks.
Should I keep the old main board?
Yes, have it assessed. If repairable, keep it as a tested spare.
Can I use a newer version main board?
Often yes, but you may need to update carriage board firmware and software, and check licences and settings compatibility. Get written confirmation from the supplier.
What costs should I include when planning a main board replacement?
Board price and landed cost, cables, software or licence fees, technician time, test materials and lost production.
What records should I keep after a main board replacement?
Date, serial number, supplier, invoice, installation photos, tests performed and any firmware, software or settings changes.