UV Printing

UV Main Board Firmware Update: Safe Steps, Risks and Recovery for Roll to Roll Printers

UV Main Board Firmware Update: Safe Steps and Recovery Guide

Direct answer: A UV main board firmware update should only be done when there is a clear reason, such as fixing a known bug, supporting a new board or head, or matching a replacement carriage board. Before updating, confirm the exact firmware file with your board supplier, back up all settings and calibration files, record current firmware and software versions, and connect the printer and PC to a UPS so power cannot fail mid-update. Follow the supplier’s sequence, which often means updating the print control software first, then the main board, then carriage and driver boards. Never switch off during an update. If something goes wrong, contact the supplier for recovery firmware rather than repeatedly retrying.

A careful UV main board firmware update fixes problems; a careless one can stop your printer completely, so preparation matters.

UV Main Board Firmware Update: Safe Steps and Recovery Guide
UV Main Board Firmware Update: Safe Steps and Recovery Guide

Firmware is the built-in program that runs on the main board, carriage board and other boards. Updates can bring improvements, but a failed or wrong update can leave a printer unable to work. This guide explains when and how to update firmware safely on BYHX, Hoson, Senyang and similar UV roll to roll systems. It follows our guides to UV main board functions and main board failure symptoms.

What firmware does

Firmware controls how each board behaves: how it talks to the PC, drives motors, reads sensors, sends data to heads and applies settings. Different boards in a system have their own firmware, and versions must be compatible with each other and with the print control software.

ComponentFirmware role
Main boardCommunication, motion control, sensors, data handling
Carriage boardData distribution, heater control
Driver / adapter boardsWaveform and head interface (on some systems)
Print control softwareUser interface, settings, calibration, job control

When to do a UV main board firmware update

  • The board supplier recommends an update to fix a known problem you are experiencing.
  • You are installing a replacement board that needs matching firmware across the system.
  • You are adding heads or upgrading heads, such as moving to Ricoh Gen6, and the update adds support.
  • A new software version requires newer firmware.

When not to update

  • The machine works well and there is no specific reason.
  • You found a file online without confirmation from your supplier.
  • Power is unstable or there is no UPS.
  • You do not have a backup of settings.
  • You are in the middle of urgent production.

“If it is not broken, do not update it” is good advice for printer firmware.

Risks of a firmware update

RiskConsequencePrevention
Power cut mid-updateBoard may not start (“bricked”)UPS on printer electronics and PC
Wrong firmware fileBoard misbehaves or will not startGet file and instructions from supplier
Version mismatch between boardsCommunication errorsUpdate in the right sequence
Settings lostCalibration and head settings resetBack up first
Licence issuesSoftware stops workingCheck licence compatibility
USB disconnect mid-updateCorrupted firmwareSecure cable; disable PC sleep

Preparation checklist

  1. Write down current firmware versions for every board and the software version.
  2. Photograph the software’s version and settings screens.
  3. Back up all settings, calibration files, head voltages, colour profiles and machine parameters.
  4. Get the correct firmware files and instructions from your board supplier, confirming they match your board versions.
  5. Check that the software licence covers the new version.
  6. Connect PC and printer electronics through a UPS.
  7. Use a good USB or network cable, secured so it cannot be pulled.
  8. Disable PC sleep, screen savers, automatic updates and antivirus scans during the update.
  9. Schedule the update when there is no urgent production and a technician is available.

Typical update sequence

Follow your supplier’s exact sequence. A common pattern is:

  1. Install or update the print control software on the PC.
  2. Update main board firmware through the software’s update tool.
  3. Restart as instructed.
  4. Update carriage and driver board firmware if required.
  5. Restart and check that all boards report the expected versions.
  6. Restore or re-enter settings as needed.
  7. Check head voltages and temperatures before printing.
  8. Run initialisation, nozzle checks and calibration prints.

Do not interrupt the process even if progress seems slow. Some steps take several minutes.

After the update

  • Confirm head settings, especially voltages, have not reset to defaults. See our guide to Ricoh Gen5 head voltage settings.
  • Check head alignment, feed calibration and bidirectional settings.
  • Check lamp settings and white ink circulation settings.
  • Print test jobs before production.
  • Record new versions and the date.

Recovering from a failed update

  1. Do not keep retrying blindly.
  2. Record exactly what happened and any error messages.
  3. Check power, cables and PC settings.
  4. Contact the board supplier. Many systems have recovery modes or recovery firmware.
  5. If recovery is not possible on site, the board may need reprogramming by the supplier or a technician with suitable tools.

Firmware and replacement boards

A replacement main board or carriage board may arrive with different firmware than your existing boards. Ask the supplier before buying whether firmware updates are needed and which versions to use. Our article on main board replacement, dongles and licences covers this.

Firmware and head upgrades

Adding heads or moving from Ricoh Gen5 to Gen6 often needs firmware and software that support the new configuration, plus compatible boards. Firmware alone rarely turns a Gen5 board into a Gen6 board. See our guide on Ricoh Gen5 to Gen6 upgrades.

Example: settings lost after update

A unit updated their print control software and main board firmware on advice from a reseller. The update succeeded, but head voltages reset to defaults. Printing became weak and spraying on different heads. Fortunately, they had photographed the old settings and restored them. Without that record, recalibration would have taken a day.

Example: update during a power cut

Another unit started a firmware update without a UPS. A power cut interrupted it, and the main board would not start. The supplier provided recovery firmware and instructions, and the board was restored the next day. They now update only with a UPS and backups.

Version records: a simple template

ItemBefore updateAfter update
Print control softwareVersionVersion
Main board firmwareVersionVersion
Carriage board firmwareVersionVersion
Driver / adapter firmwareVersionVersion
Licence statusActive / codeActive / code
Date and technicianDetails
Reason for updateDetails

Keep this record with your machine documents. When something goes wrong months later, knowing exactly what changed and when is invaluable.

Testing after an update

A structured test confirms the update has not introduced problems:

  1. Initialise and check carriage movement, origin and limits.
  2. Check media feed and take-up.
  3. Check head temperatures and voltages.
  4. Print nozzle checks on all heads.
  5. Check lamp operation and power levels.
  6. Check white ink circulation and any varnish functions.
  7. Run alignment and feed calibration.
  8. Print a standard test image and compare with a reference print from before the update.
  9. Run a long job to check stability.

Keep a reference print made before the update. Comparing side by side is the quickest way to spot changes in colour, density or registration.

Firmware and the PC

Firmware updates are usually performed from the print control PC. Prepare it properly: close other programs, disable sleep and automatic updates, use a reliable USB port or network connection, and make sure the PC is on a UPS. If the PC is old or unstable, consider using a more reliable PC for the update.

Who should perform updates

For routine software updates recommended by the supplier, a trained senior operator may be able to follow instructions. For main board and carriage board firmware updates, especially when replacing boards or adding heads, a technician familiar with the board system should be present. The cost of a technician’s time is small compared with the risk of a failed update.

Firmware myths

MythReality
Newer firmware is always betterNew firmware can bring new bugs or require other changes
Firmware updates improve print qualityQuality depends mainly on heads, ink, calibration and RIP
Any firmware for my board model will workVersions must match board revisions and other boards
A failed update always destroys the boardMany boards can be recovered with supplier help

Firmware updates for different board systems

The process varies by system, but most follow similar principles:

SystemTypical update methodNotes
BYHXUpdate tools within or alongside print control softwareBoard-specific files; follow version guidance
HosonSoftware-based update toolsMain and carriage boards may update separately
SenyangSoftware-based update toolsCommon on Epson-based machines
Manufacturer-specificMachine maker’s toolsOften only through maker or reseller

Never use update files intended for another system or board version. Always get files and instructions directly from your supplier.

Common update errors and responses

ErrorLikely causeResponse
Update tool cannot find boardConnection or driverCheck cable, drivers, power
Update fails partwayConnection drop or wrong fileDo not power off; contact supplier
Board version mismatch warningWrong file for board revisionStop and confirm correct file
Software will not start after updateLicence or version conflictContact supplier with version details
Printer behaves strangelySettings reset or incompatibleRestore settings; check versions

Firmware and security

Print PCs connected to the internet can be exposed to malware. Download firmware only from trusted sources, scan files as advised by your IT support, and avoid using USB drives that have been used on unknown computers. A compromised PC could corrupt software or settings.

Planning updates across a fleet

If you run several printers with the same board system, update one machine first and run it in production for a period before updating others. This reduces the risk of all machines being affected by a problem in a new version.

Firmware and replacement carriage boards

A frequent reason for firmware work is replacing a carriage board. The new board may have firmware that is newer or older than the main board expects. Possible approaches, depending on the system, include updating the new board to match the existing version, updating all boards to a newer common version, or ordering a board pre-loaded with your version. Ask your supplier which approach is recommended and get the correct files before the board arrives.

Example: correct sequence saved the day

A unit in Lucknow added two heads for white and varnish, which required a newer carriage board. The supplier specified updating the software first, then the main board, then the new carriage board. The technician followed the sequence exactly, with a UPS and backups in place. Everything worked on the first attempt, and the only extra time needed was for calibrating the new heads.

Signs you may need an update

  • Your supplier identifies a known bug matching your symptoms.
  • A replacement board reports a version mismatch.
  • New heads or head counts are not recognised.
  • Your RIP or software vendor requires a newer version for compatibility.

Without one of these reasons, leave working firmware alone.

Communicating with your supplier about updates

When asking a supplier about an update, give them the printer model, board system, board part numbers and versions, current software and firmware versions, head type and count, and the exact problem you hope to solve. Ask them to confirm in writing which files to use, the update order, whether settings will be kept and whether the licence is affected. Clear communication avoids most update mistakes.

Bottom line

A UV main board firmware update is a controlled procedure, not a routine task. Update only for a clear reason, with supplier-approved files, full backups, a UPS and a technician on hand. Follow the correct sequence, never interrupt, and test thoroughly afterwards. Treated this way, firmware updates solve problems instead of creating them.

Further reading: Each board runs its own firmware, and versions must stay compatible across the whole system.

Key takeaways

  • Do a UV main board firmware update only for a clear reason and with supplier confirmation.
  • Back up settings, record versions and use a UPS.
  • Follow the supplier’s update sequence and never interrupt it.
  • Check and restore settings after updating.
  • Contact the supplier for recovery if an update fails.

More in the UV main board series

Related reading on our site: UV roll to roll printer price in India, Ricoh Gen5 vs Gen5i printheads, UV LED lamp and module replacement checks, UV curing problems: lamp, ink and power checks and white ink circulation engineering.

Also running solvent or eco-solvent machines? See our sister guides to the solvent flex machine main board and the eco-solvent printer main board.

Frequently Asked Questions

Should I update my UV printer’s firmware regularly?

Not routinely. Update only when there is a specific reason, such as a known bug fix, a replacement board or a head upgrade.

What happens if power fails during a firmware update?

The board may fail to start. Use a UPS and contact the supplier for recovery firmware if it happens.

Where do I get firmware for my main board?

From your board supplier or machine supplier. Avoid files of unknown origin.

Will a firmware update erase my settings?

It can. Always back up settings, calibration files and head voltages before updating.

Do all boards need the same firmware version?

Boards in a system need compatible versions. Follow the supplier’s guidance on which versions work together.

Can firmware make a Gen5 board support Gen6 heads?

Usually not. Gen6 generally needs compatible boards as well as firmware and software support.

Why does my printer not connect after an update?

Possible causes include version mismatch, wrong firmware, licence issues or incomplete update. Contact the supplier.

Can I update firmware myself?

Trained operators can follow supplier instructions, but having a technician available is wise.

How long does a firmware update take?

It varies from a few minutes to longer for multiple boards. Do not interrupt it.

Do I need to recalibrate after a firmware update?

Often yes. Check head settings, alignment and feed calibration and print tests.

Is a UPS really necessary for updates?

Yes. A power cut during an update is one of the most common causes of board failure after updates.

Can Unified Engineering Dynamics help with firmware updates?

Yes. Our team can advise on firmware compatibility and board replacements for UV roll to roll printers.

Will a firmware update improve print quality?

Rarely. Print quality depends mainly on heads, ink, calibration and RIP settings. Updates mainly fix bugs and add support for hardware.

Should I keep a reference print before updating?

Yes. Comparing a reference print with a post-update print quickly reveals any changes in colour, density or registration.

Can I use firmware from another board system?

No. Firmware is specific to the board system and version. Using the wrong file can make the board unusable.

Should I update all my printers at once?

It is safer to update one machine first and run it in production before updating others.

Does a replacement carriage board need a firmware update?

Often. The new board’s firmware must be compatible with the main board and software. Ask your supplier which versions to use.

What information should I give my supplier before an update?

Printer model, board system, part numbers and versions, current firmware and software versions, head details and the problem you want to fix.

author-avatar

About Avinash Sharma

Avinash Sharma is the founder of Unified Engineering Dynamics (UED), an industrial digital printing machine supplier and engineering consultancy based in Uttar Pradesh, India. He works hands-on with flex printers, eco-solvent printers, UV flatbed and hybrid printers, DTF and sublimation machines, CO2 lasers and CNC routers - from installation and operator training to cost-per-print economics for new printing plants. His guides help first-time buyers across India choose the right machine for their budget, products and city, with honest setup costs and maintenance realities.

Related Posts

Leave a Reply

Your email address will not be published. Required fields are marked *